mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: T Pratham <t-pratham@ti.com>
To: T Pratham <t-pratham@ti.com>,
	Herbert Xu <herbert@gondor.apana.org.au>,
	"David S. Miller" <davem@davemloft.net>
Cc: Manorit Chawdhry <m-chawdhry@ti.com>,
	Kamlesh Gurudasani <kamlesh@ti.com>,
	Shiva Tripathi <s-tripathi1@ti.com>,
	Kavitha Malarvizhi <k-malarvizhi@ti.com>,
	Vishal Mahaveer <vishalm@ti.com>,
	Praneeth Bajjuri <praneeth@ti.com>,
	<linux-crypto@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v4 2/4] crypto: ti - Add support for AES-CTR in DTHEv2 driver
Date: Thu, 9 Oct 2025 16:11:32 +0530	[thread overview]
Message-ID: <20251009111727.911738-3-t-pratham@ti.com> (raw)
In-Reply-To: <20251009111727.911738-1-t-pratham@ti.com>

Add support for CTR mode of operation for AES algorithm in the AES
Engine of the DTHEv2 hardware cryptographic engine.

Signed-off-by: T Pratham <t-pratham@ti.com>
---
 drivers/crypto/ti/Kconfig         |   1 +
 drivers/crypto/ti/dthev2-aes.c    | 101 +++++++++++++++++++++++++++---
 drivers/crypto/ti/dthev2-common.c |  19 ++++++
 drivers/crypto/ti/dthev2-common.h |  15 +++++
 4 files changed, 127 insertions(+), 9 deletions(-)

diff --git a/drivers/crypto/ti/Kconfig b/drivers/crypto/ti/Kconfig
index a3692ceec49bc..6027e12de279d 100644
--- a/drivers/crypto/ti/Kconfig
+++ b/drivers/crypto/ti/Kconfig
@@ -6,6 +6,7 @@ config CRYPTO_DEV_TI_DTHEV2
 	select CRYPTO_SKCIPHER
 	select CRYPTO_ECB
 	select CRYPTO_CBC
+	select CRYPTO_CTR
 	select CRYPTO_XTS
 	help
 	  This enables support for the TI DTHE V2 hw cryptography engine
diff --git a/drivers/crypto/ti/dthev2-aes.c b/drivers/crypto/ti/dthev2-aes.c
index 4a1113e56c328..ba2cd49c4b5e3 100644
--- a/drivers/crypto/ti/dthev2-aes.c
+++ b/drivers/crypto/ti/dthev2-aes.c
@@ -63,6 +63,7 @@
 enum aes_ctrl_mode_masks {
 	AES_CTRL_ECB_MASK = 0x00,
 	AES_CTRL_CBC_MASK = BIT(5),
+	AES_CTRL_CTR_MASK = BIT(6),
 	AES_CTRL_XTS_MASK = BIT(12) | BIT(11),
 };
 
@@ -74,6 +75,8 @@ enum aes_ctrl_mode_masks {
 #define DTHE_AES_CTRL_KEYSIZE_24B		BIT(4)
 #define DTHE_AES_CTRL_KEYSIZE_32B		(BIT(3) | BIT(4))
 
+#define DTHE_AES_CTRL_CTR_WIDTH_128B		(BIT(7) | BIT(8))
+
 #define DTHE_AES_CTRL_SAVE_CTX_SET		BIT(29)
 
 #define DTHE_AES_CTRL_OUTPUT_READY		BIT_MASK(0)
@@ -159,6 +162,15 @@ static int dthe_aes_cbc_setkey(struct crypto_skcipher *tfm, const u8 *key, unsig
 	return dthe_aes_setkey(tfm, key, keylen);
 }
 
+static int dthe_aes_ctr_setkey(struct crypto_skcipher *tfm, const u8 *key, unsigned int keylen)
+{
+	struct dthe_tfm_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	ctx->aes_mode = DTHE_AES_CTR;
+
+	return dthe_aes_setkey(tfm, key, keylen);
+}
+
 static int dthe_aes_xts_setkey(struct crypto_skcipher *tfm, const u8 *key, unsigned int keylen)
 {
 	struct dthe_tfm_ctx *ctx = crypto_skcipher_ctx(tfm);
@@ -239,6 +251,10 @@ static void dthe_aes_set_ctrl_key(struct dthe_tfm_ctx *ctx,
 	case DTHE_AES_CBC:
 		ctrl_val |= AES_CTRL_CBC_MASK;
 		break;
+	case DTHE_AES_CTR:
+		ctrl_val |= AES_CTRL_CTR_MASK;
+		ctrl_val |= DTHE_AES_CTRL_CTR_WIDTH_128B;
+		break;
 	case DTHE_AES_XTS:
 		ctrl_val |= AES_CTRL_XTS_MASK;
 		break;
@@ -274,11 +290,14 @@ static int dthe_aes_run(struct crypto_engine *engine, void *areq)
 	struct scatterlist *dst = req->dst;
 
 	int src_nents = sg_nents_for_len(src, len);
-	int dst_nents;
+	int dst_nents = sg_nents_for_len(dst, len);
 
 	int src_mapped_nents;
 	int dst_mapped_nents;
 
+	u8 pad_buf[AES_BLOCK_SIZE] = {0};
+	int pad_len = 0;
+
 	bool diff_dst;
 	enum dma_data_direction src_dir, dst_dir;
 
@@ -298,6 +317,39 @@ static int dthe_aes_run(struct crypto_engine *engine, void *areq)
 	aes_irqenable_val |= DTHE_AES_IRQENABLE_EN_ALL;
 	writel_relaxed(aes_irqenable_val, aes_base_reg + DTHE_P_AES_IRQENABLE);
 
+	if (ctx->aes_mode == DTHE_AES_CTR) {
+		/*
+		 * CTR mode can operate on any input length, but the hardware
+		 * requires input length to be a multiple of the block size.
+		 * We need to handle the padding in the driver.
+		 */
+		if (req->cryptlen % AES_BLOCK_SIZE) {
+			/* Need to create a new SG list with padding */
+			pad_len = ALIGN(req->cryptlen, AES_BLOCK_SIZE) - req->cryptlen;
+			struct scatterlist *sg;
+
+			src = kmalloc_array((src_nents + 1), sizeof(*src), GFP_KERNEL);
+			if (!src) {
+				ret = -ENOMEM;
+				goto aes_src_alloc_err;
+			}
+			sg_init_table(src, src_nents + 1);
+			sg = dthe_copy_sg(src, req->src, req->cryptlen);
+			sg_set_buf(sg, pad_buf, pad_len);
+			src_nents++;
+
+			dst = kmalloc_array(dst_nents + 1, sizeof(*dst), GFP_KERNEL);
+			if (!dst) {
+				ret = -ENOMEM;
+				goto aes_dst_alloc_err;
+			}
+			sg_init_table(dst, dst_nents + 1);
+			sg = dthe_copy_sg(dst, req->dst, req->cryptlen);
+			sg_set_buf(sg, pad_buf, pad_len);
+			dst_nents++;
+		}
+	}
+
 	if (src == dst) {
 		diff_dst = false;
 		src_dir = DMA_BIDIRECTIONAL;
@@ -314,19 +366,16 @@ static int dthe_aes_run(struct crypto_engine *engine, void *areq)
 	src_mapped_nents = dma_map_sg(tx_dev, src, src_nents, src_dir);
 	if (src_mapped_nents == 0) {
 		ret = -EINVAL;
-		goto aes_err;
+		goto aes_map_src_err;
 	}
 
 	if (!diff_dst) {
-		dst_nents = src_nents;
 		dst_mapped_nents = src_mapped_nents;
 	} else {
-		dst_nents = sg_nents_for_len(dst, len);
 		dst_mapped_nents = dma_map_sg(rx_dev, dst, dst_nents, dst_dir);
 		if (dst_mapped_nents == 0) {
-			dma_unmap_sg(tx_dev, src, src_nents, src_dir);
 			ret = -EINVAL;
-			goto aes_err;
+			goto aes_map_dst_err;
 		}
 	}
 
@@ -389,11 +438,19 @@ static int dthe_aes_run(struct crypto_engine *engine, void *areq)
 	}
 
 aes_prep_err:
-	dma_unmap_sg(tx_dev, src, src_nents, src_dir);
 	if (dst_dir != DMA_BIDIRECTIONAL)
 		dma_unmap_sg(rx_dev, dst, dst_nents, dst_dir);
+aes_map_dst_err:
+	dma_unmap_sg(tx_dev, src, src_nents, src_dir);
+
+aes_map_src_err:
+	if (ctx->aes_mode == DTHE_AES_CTR && req->cryptlen % AES_BLOCK_SIZE) {
+		kfree(dst);
+aes_dst_alloc_err:
+		kfree(src);
+	}
 
-aes_err:
+aes_src_alloc_err:
 	local_bh_disable();
 	crypto_finalize_skcipher_request(dev_data->engine, req, ret);
 	local_bh_enable();
@@ -411,6 +468,7 @@ static int dthe_aes_crypt(struct skcipher_request *req)
 	 * If data is not a multiple of AES_BLOCK_SIZE:
 	 * - need to return -EINVAL for ECB, CBC as they are block ciphers
 	 * - need to fallback to software as H/W doesn't support Ciphertext Stealing for XTS
+	 * - do nothing for CTR
 	 */
 	if (req->cryptlen % AES_BLOCK_SIZE) {
 		if (ctx->aes_mode == DTHE_AES_XTS) {
@@ -428,7 +486,8 @@ static int dthe_aes_crypt(struct skcipher_request *req)
 
 			return ret;
 		}
-		return -EINVAL;
+		if (ctx->aes_mode != DTHE_AES_CTR)
+			return -EINVAL;
 	}
 
 	/*
@@ -507,6 +566,30 @@ static struct skcipher_engine_alg cipher_algs[] = {
 		},
 		.op.do_one_request = dthe_aes_run,
 	}, /* CBC AES */
+	{
+		.base.init			= dthe_cipher_init_tfm,
+		.base.setkey			= dthe_aes_ctr_setkey,
+		.base.encrypt			= dthe_aes_encrypt,
+		.base.decrypt			= dthe_aes_decrypt,
+		.base.min_keysize		= AES_MIN_KEY_SIZE,
+		.base.max_keysize		= AES_MAX_KEY_SIZE,
+		.base.ivsize			= AES_IV_SIZE,
+		.base.chunksize			= AES_BLOCK_SIZE,
+		.base.base = {
+			.cra_name		= "ctr(aes)",
+			.cra_driver_name	= "ctr-aes-dthev2",
+			.cra_priority		= 299,
+			.cra_flags		= CRYPTO_ALG_TYPE_SKCIPHER |
+						  CRYPTO_ALG_ASYNC |
+						  CRYPTO_ALG_KERN_DRIVER_ONLY |
+						  CRYPTO_ALG_ALLOCATES_MEMORY,
+			.cra_blocksize		= 1,
+			.cra_ctxsize		= sizeof(struct dthe_tfm_ctx),
+			.cra_reqsize		= sizeof(struct dthe_aes_req_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.op.do_one_request = dthe_aes_run,
+	}, /* CTR AES */
 	{
 		.base.init			= dthe_cipher_xts_init_tfm,
 		.base.exit			= dthe_cipher_xts_exit_tfm,
diff --git a/drivers/crypto/ti/dthev2-common.c b/drivers/crypto/ti/dthev2-common.c
index c39d37933b9ee..a2ad79bec105a 100644
--- a/drivers/crypto/ti/dthev2-common.c
+++ b/drivers/crypto/ti/dthev2-common.c
@@ -48,6 +48,25 @@ struct dthe_data *dthe_get_dev(struct dthe_tfm_ctx *ctx)
 	return dev_data;
 }
 
+struct scatterlist *dthe_copy_sg(struct scatterlist *dst,
+				 struct scatterlist *src,
+				 int buflen)
+{
+	struct scatterlist *from_sg, *to_sg;
+	int sglen;
+
+	for (to_sg = dst, from_sg = src; buflen && from_sg; buflen -= sglen) {
+		sglen = from_sg->length;
+		if (sglen > buflen)
+			sglen = buflen;
+		sg_set_buf(to_sg, sg_virt(from_sg), sglen);
+		from_sg = sg_next(from_sg);
+		to_sg = sg_next(to_sg);
+	}
+
+	return to_sg;
+}
+
 static int dthe_dma_init(struct dthe_data *dev_data)
 {
 	int ret;
diff --git a/drivers/crypto/ti/dthev2-common.h b/drivers/crypto/ti/dthev2-common.h
index 4399ab62e1b12..5c2fc1fb4793f 100644
--- a/drivers/crypto/ti/dthev2-common.h
+++ b/drivers/crypto/ti/dthev2-common.h
@@ -36,6 +36,7 @@
 enum dthe_aes_mode {
 	DTHE_AES_ECB = 0,
 	DTHE_AES_CBC,
+	DTHE_AES_CTR,
 	DTHE_AES_XTS,
 };
 
@@ -105,6 +106,20 @@ struct dthe_aes_req_ctx {
 
 struct dthe_data *dthe_get_dev(struct dthe_tfm_ctx *ctx);
 
+/**
+ * dthe_copy_sg - Copy sg entries from src to dst
+ * @dst: Destination sg to be filled
+ * @src: Source sg to be copied from
+ * @buflen: Number of bytes to be copied
+ *
+ * Description:
+ *   Copy buflen bytes of data from src to dst.
+ *
+ **/
+struct scatterlist *dthe_copy_sg(struct scatterlist *dst,
+				 struct scatterlist *src,
+				 int buflen);
+
 int dthe_register_aes_algs(void);
 void dthe_unregister_aes_algs(void);
 
-- 
2.43.0


  parent reply	other threads:[~2025-10-09 11:18 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-10-09 10:41 [PATCH v4 0/4] Add support for more AES modes in TI DTHEv2 T Pratham
2025-10-09 10:41 ` [PATCH v4 1/4] crypto: ti - Add support for AES-XTS in DTHEv2 driver T Pratham
2025-10-17  5:41   ` Herbert Xu
2025-10-17 16:43     ` T Pratham
2025-10-21 15:10       ` T Pratham
2025-10-22  0:35         ` Herbert Xu
2025-10-09 10:41 ` T Pratham [this message]
2025-10-09 10:41 ` [PATCH v4 3/4] crypto: ti - Add support for AES-GCM " T Pratham
2025-10-09 10:41 ` [PATCH v4 4/4] crypto: ti - Add support for AES-CCM " T Pratham

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20251009111727.911738-3-t-pratham@ti.com \
    --to=t-pratham@ti.com \
    --cc=davem@davemloft.net \
    --cc=herbert@gondor.apana.org.au \
    --cc=k-malarvizhi@ti.com \
    --cc=kamlesh@ti.com \
    --cc=linux-crypto@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=m-chawdhry@ti.com \
    --cc=praneeth@ti.com \
    --cc=s-tripathi1@ti.com \
    --cc=vishalm@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®