[PATCH] spi: imx: keep dma request disabled before dma transfer setup

[carlos.song@nxp.com]

From: Robin Gong <yibin.gong@nxp.com>

Since sdma hardware configure postpone to transfer phase, have to disable
dma request before dma transfer setup because there is a hardware
limitation on sdma event enable(ENBLn) as below:

"It is thus essential for the Arm platform to program them before any DMA
 request is triggered to the SDMA, otherwise an unpredictable combination
 of channels may be started."

Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
---
 drivers/spi/spi-imx.c | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)

diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index cd40db61d8d1..765ea507dd8d 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -529,9 +529,15 @@ static void mx51_ecspi_trigger(struct spi_imx_data *spi_imx)
 {
 	u32 reg;
 
-	reg = readl(spi_imx->base + MX51_ECSPI_CTRL);
-	reg |= MX51_ECSPI_CTRL_XCH;
-	writel(reg, spi_imx->base + MX51_ECSPI_CTRL);
+	if (spi_imx->usedma) {
+		reg = readl(spi_imx->base + MX51_ECSPI_DMA);
+		reg |= MX51_ECSPI_DMA_TEDEN | MX51_ECSPI_DMA_RXDEN;
+		writel(reg, spi_imx->base + MX51_ECSPI_DMA);
+	} else {
+		reg = readl(spi_imx->base + MX51_ECSPI_CTRL);
+		reg |= MX51_ECSPI_CTRL_XCH;
+		writel(reg, spi_imx->base + MX51_ECSPI_CTRL);
+	}
 }
 
 static void mx51_ecspi_disable(struct spi_imx_data *spi_imx)
@@ -772,7 +778,6 @@ static void mx51_setup_wml(struct spi_imx_data *spi_imx)
 	writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml - 1) |
 		MX51_ECSPI_DMA_TX_WML(tx_wml) |
 		MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |
-		MX51_ECSPI_DMA_TEDEN | MX51_ECSPI_DMA_RXDEN |
 		MX51_ECSPI_DMA_RXTDEN, spi_imx->base + MX51_ECSPI_DMA);
 }
 
@@ -1539,6 +1544,8 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
 	reinit_completion(&spi_imx->dma_tx_completion);
 	dma_async_issue_pending(controller->dma_tx);
 
+	spi_imx->devtype_data->trigger(spi_imx);
+
 	transfer_timeout = spi_imx_calculate_timeout(spi_imx, transfer->len);
 
 	/* Wait SDMA to finish the data transfer.*/
-- 
2.34.1