From: Kaustabh Chakraborty <kauschluss@disroot.org>
To: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Alim Akhtar <alim.akhtar@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>,
devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org,
Kaustabh Chakraborty <kauschluss@disroot.org>
Subject: [PATCH v4 4/5] arm64: dts: exynos7870-a2corelte: enable display panel support
Date: Fri, 31 Oct 2025 00:50:18 +0530 [thread overview]
Message-ID: <20251031-exynos7870-drm-dts-v4-4-c1f77fb16b87@disroot.org> (raw)
In-Reply-To: <20251031-exynos7870-drm-dts-v4-0-c1f77fb16b87@disroot.org>
Enable DECON and DSI nodes, and add the compatible display panel and
appropriate panel timings for this device. Also, remove the
simple-framebuffer node in favor of the panel.
This device has a 540x960 Synaptics TD4101 display panel.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
.../arm64/boot/dts/exynos/exynos7870-a2corelte.dts | 57 ++++++++++++++++------
1 file changed, 43 insertions(+), 14 deletions(-)
diff --git a/arch/arm64/boot/dts/exynos/exynos7870-a2corelte.dts b/arch/arm64/boot/dts/exynos/exynos7870-a2corelte.dts
index 07467158ee6a37e17402fb50554184c4c93f77d5..6f40ca4350ed72b57e511165e53f00e77f8978f3 100644
--- a/arch/arm64/boot/dts/exynos/exynos7870-a2corelte.dts
+++ b/arch/arm64/boot/dts/exynos/exynos7870-a2corelte.dts
@@ -27,20 +27,7 @@ aliases {
};
chosen {
- #address-cells = <2>;
- #size-cells = <1>;
- ranges;
-
stdout-path = &serial2;
-
- framebuffer@67000000 {
- compatible = "simple-framebuffer";
- reg = <0x0 0x67000000 (540 * 960 * 4)>;
- width = <540>;
- height = <960>;
- stride = <(540 * 4)>;
- format = "a8r8g8b8";
- };
};
gpio-keys {
@@ -110,8 +97,9 @@ ramoops@46800000 {
pmsg-size = <0x4000>;
};
- framebuffer@67000000 {
+ cont_splash_mem: framebuffer@67000000 {
reg = <0x0 0x67000000 (540 * 960 * 4)>;
+ iommu-addresses = <&decon 0x67000000 (540 * 960 * 4)>;
no-map;
};
};
@@ -124,6 +112,47 @@ vibrator {
};
};
+&decon {
+ memory-region = <&cont_splash_mem>;
+
+ status = "okay";
+};
+
+&dsi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ samsung,burst-clock-frequency = <836000000>;
+ samsung,esc-clock-frequency = <16000000>;
+ samsung,pll-clock-frequency = <26000000>;
+
+ status = "okay";
+
+ panel@0 {
+ compatible = "syna,td4101-panel";
+ reg = <0>;
+
+ backlight-gpios = <&gpd3 7 GPIO_ACTIVE_LOW>;
+
+ width-mm = <62>;
+ height-mm = <110>;
+
+ panel-timing {
+ clock-frequency = <69336720>;
+
+ hactive = <540>;
+ hsync-len = <4>;
+ hfront-porch = <364>;
+ hback-porch = <40>;
+
+ vactive = <960>;
+ vsync-len = <2>;
+ vfront-porch = <244>;
+ vback-porch = <13>;
+ };
+ };
+};
+
&gpu {
status = "okay";
};
--
2.51.0
next prev parent reply other threads:[~2025-10-30 19:21 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-30 19:20 [PATCH v4 0/5] Support for Exynos7870's display stack (DECON, MIPIPHY, DSIM, etc.) Kaustabh Chakraborty
2025-10-30 19:20 ` [PATCH v4 1/5] dt-bindings: soc: samsung: exynos-pmu: allow mipi-phy subnode for Exynos7870 PMU Kaustabh Chakraborty
2025-10-31 0:37 ` Rob Herring (Arm)
2025-11-05 7:25 ` (subset) " Krzysztof Kozlowski
2025-10-30 19:20 ` [PATCH v4 2/5] arm64: dts: exynos7870: add DSI support Kaustabh Chakraborty
2025-11-05 7:25 ` (subset) " Krzysztof Kozlowski
2025-10-30 19:20 ` [PATCH v4 3/5] arm64: dts: exynos7870-on7xelte: enable display panel support Kaustabh Chakraborty
2025-11-05 7:25 ` (subset) " Krzysztof Kozlowski
2025-10-30 19:20 ` Kaustabh Chakraborty [this message]
2025-11-05 7:25 ` (subset) [PATCH v4 4/5] arm64: dts: exynos7870-a2corelte: " Krzysztof Kozlowski
2025-10-30 19:20 ` [PATCH v4 5/5] arm64: dts: exynos7870-j6lte: " Kaustabh Chakraborty
2025-11-05 7:25 ` (subset) " Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251031-exynos7870-drm-dts-v4-4-c1f77fb16b87@disroot.org \
--to=kauschluss@disroot.org \
--cc=alim.akhtar@samsung.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=krzk@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®