[PATCH v2 2/9] docs: iio: New docs for ad4062 driver

[Jorge Marques <jorge.marques@analog.com>]

This adds a new page to document how to use the ad4062 ADC driver.

Signed-off-by: Jorge Marques <jorge.marques@analog.com>
---
 Documentation/iio/ad4062.rst | 94 ++++++++++++++++++++++++++++++++++++++++++++
 Documentation/iio/index.rst  |  1 +
 MAINTAINERS                  |  1 +
 3 files changed, 96 insertions(+)

diff --git a/Documentation/iio/ad4062.rst b/Documentation/iio/ad4062.rst
new file mode 100644
index 0000000000000..e6bcca2bef24b
--- /dev/null
+++ b/Documentation/iio/ad4062.rst
@@ -0,0 +1,94 @@
+.. SPDX-License-Identifier: GPL-2.0-only
+
+=============
+AD4062 driver
+=============
+
+ADC driver for Analog Devices Inc. AD4060/AD4062 devices. The module name is
+``ad4062``.
+
+Supported devices
+=================
+
+The following chips are supported by this driver:
+
+* `AD4060 <https://www.analog.com/AD4060>`_
+* `AD4062 <https://www.analog.com/AD4062>`_
+
+Wiring modes
+============
+
+The ADC is interfaced through an I3C bus, and contains two programmable GPIOs.
+
+The ADC convert-start happens on the SDA rising edge of the I3C stop (P) bit
+at the end of the read command.
+
+The two programmable GPIOS are optional and have a role assigned if present in
+the devicetree ``interrupt-names`` property:
+
+- GP1: Is assigned the role of Data Ready signal.
+
+Device attributes
+=================
+
+The ADC contains only one channel with following attributes:
+
+.. list-table:: Channel attributes
+   :header-rows: 1
+
+   * - Attribute
+     - Description
+   * - ``in_voltage_calibscale``
+     - Sets the gain scaling factor that the hardware applies to the sample,
+       to compensate for system gain error.
+   * - ``in_voltage_oversampling_ratio``
+     - Sets device's burst averaging mode to over sample using the
+       internal sample rate. Value 1 disable the burst averaging mode.
+   * - ``in_voltage_oversampling_ratio_available``
+     - List of available oversampling values.
+   * - ``in_voltage_raw``
+     - Returns the raw ADC voltage value.
+   * - ``in_voltage_scale``
+     - Returns the channel scale in reference to the reference voltage
+       ``ref-supply`` or ``vdd-supply`` if the former not present.
+
+Also contain the following device attributes:
+
+.. list-table:: Device attributes
+   :header-rows: 1
+
+   * - Attribute
+     - Description
+   * - ``sampling_frequency``
+     - Sets the duration of a single scan, used in the burst averaging mode.
+       The duration is described by ``(n_avg - 1) / fosc + tconv``, where
+       ``n_avg`` is the oversampling ratio, ``fosc`` is the internal sample
+       rate and ``tconv`` is the ADC conversion time.
+   * - ``sampling_frequency_available``
+     - Lists the available sampling frequencies, computed on the current
+       oversampling ratio. If the ratio is 1, the frequency is ``1/tconv``.
+
+Interrupts
+==========
+
+The interrupts are mapped through the ``interrupt-names`` and ``interrupts``
+properties.
+
+The ``interrupt-names`` ``gp1`` entry sets the role of Data Ready signal.
+If it is not present, the driver fallback to enabling the same role as an
+I3C IBI.
+
+Low-power mode
+==============
+
+The device enters low-power mode on idle to save power. Enabling an event puts
+the device out of the low-power since the ADC autonomously samples to assert
+the event condition.
+
+Unimplemented features
+======================
+
+- Monitor mode
+- Trigger mode
+- Averaging mode
+- General purpose output
diff --git a/Documentation/iio/index.rst b/Documentation/iio/index.rst
index 315ae37d6fd4b..ba3e609c6a13c 100644
--- a/Documentation/iio/index.rst
+++ b/Documentation/iio/index.rst
@@ -22,6 +22,7 @@ Industrial I/O Kernel Drivers
    ad3552r
    ad4000
    ad4030
+   ad4062
    ad4695
    ad7191
    ad7380
diff --git a/MAINTAINERS b/MAINTAINERS
index e22ba5ec8c849..8fc28b789d639 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1437,6 +1437,7 @@ M:	Jorge Marques <jorge.marques@analog.com>
 S:	Supported
 W:	https://ez.analog.com/linux-software-drivers
 F:	Documentation/devicetree/bindings/iio/adc/adi,ad4062.yaml
+F:	Documentation/iio/ad4062.rst
 
 ANALOG DEVICES INC AD4080 DRIVER
 M:	Antoniu Miclaus <antoniu.miclaus@analog.com>

-- 
2.51.1