Re: [PATCH 2/3] thermal: K1: Add driver for K1 SoC thermal sensor

[Yixun Lan <dlan@gentoo.org>]

Hi Shuwei, 

for the title, you could simplify it by adding short prefix/annotation with
my previous comments

thermal: K1: Add driver for K1 SoC thermal sensor
-> thermal: spacemit: k1: Add thermal sensor support


On 02:44 Thu 27 Nov     , Shuwei Wu wrote:
> The thermal sensor unit (TSU) on K1 supports monitoring five temperature
> zones. The driver registers these sensors with the thermal framework
> and supports standard operations:
> - Reading temperature (millidegree Celsius)
> - Setting high/low thresholds for interrupts
> 
> Signed-off-by: Shuwei Wu <shuweiwoo@163.com>
> ---
>  drivers/thermal/Kconfig      |  14 ++
>  drivers/thermal/Makefile     |   1 +
>  drivers/thermal/k1_thermal.c | 307 +++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 322 insertions(+)
> 
> +}
[snip]..
> +
> +static int k1_thermal_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct k1_thermal_priv *priv;
> +	int i, irq, ret;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	priv->dev = dev;
> +	platform_set_drvdata(pdev, priv);
> +
> +	priv->base = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(priv->base))
> +		return PTR_ERR(priv->base);
> +
> +	priv->reset = devm_reset_control_get_exclusive_deasserted(dev, NULL);
> +	if (IS_ERR(priv->reset))
> +		return dev_err_probe(dev, PTR_ERR(priv->reset),
> +				     "Failed to get/deassert reset control\n");
no need to break the line, it's ok to have 100 column per line
https://elixir.bootlin.com/linux/v6.18-rc7/source/Documentation/dev-tools/checkpatch.rst#L688

P.S: this isn't hard rule and may still up to maintainer..
> +
> +	priv->clk = devm_clk_get_enabled(dev, "core");
> +	if (IS_ERR(priv->clk))
> +		return dev_err_probe(dev, PTR_ERR(priv->clk),
> +				     "Failed to get core clock\n");
ditto
> +
> +	priv->bus_clk = devm_clk_get_enabled(dev, "bus");
> +	if (IS_ERR(priv->bus_clk))
> +		return dev_err_probe(dev, PTR_ERR(priv->bus_clk),
> +				     "Failed to get bus clock\n");
ditto
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return irq;
I suggest to group this with dev_request_threaded_irq(), since both of them
are taking care of IRQ related operation
> +
> +	ret = k1_init_sensors(pdev);
> +
> +	for (i = 0; i < MAX_SENSOR_NUMBER; ++i) {
> +		priv->sensors[i].id = i;
> +		priv->sensors[i].priv = priv;
> +		priv->sensors[i].tzd = devm_thermal_of_zone_register(dev,
> +									i, priv->sensors + i,
> +									&k1_thermal_ops);
                                                                  ~~~~~~~~
here is wrong, alignment should match open parentheses, didn't checkpatch.pl warn about this?

> +		if (IS_ERR(priv->sensors[i].tzd))
> +			return dev_err_probe(dev, PTR_ERR(priv->sensors[i].tzd),
> +						"Failed to register thermal zone: %d\n", i);
I'd say, no need to do the verbose print, almost every error path has
print message already
> +
> +		/* Attach sysfs hwmon attributes for userspace monitoring */
> +		ret = devm_thermal_add_hwmon_sysfs(dev, priv->sensors[i].tzd);
> +		if (ret)
> +			dev_warn(dev, "Failed to add hwmon sysfs attributes\n");
> +
> +		k1_enable_sensor_irq(priv->sensors + i);
> +	}
> +
> +	ret = devm_request_threaded_irq(dev, irq, NULL,
> +					k1_thermal_irq_thread,
> +					IRQF_ONESHOT, "k1_thermal", priv);
> +	if (ret < 0)
> +		return dev_err_probe(dev, ret, "Failed to request IRQ\n");
no need to print extra error message, please refer to:
 https://lore.kernel.org/all/20250805092922.135500-2-panchuang@vivo.com
 https://github.com/torvalds/linux/commit/55b48e23f5c4b6f5ca9b7ab09599b17dcf501c10

-- 
Yixun Lan (dlan)