[PATCH] arm64: dts: qcom: lemans-evk: Add host mode support for USB1 controller

[Swati Agarwal <swati.agarwal@oss.qualcomm.com>]

Enable Host mode support for USB1 controller on EVK Platform.

For secondary USB Typec port, there is a genesys USB HUB sitting in between
SOC and HD3SS3220 Type-C port controller and SS lines run from the SoC
through the hub to the Port controller. Mark the second USB controller as
host only capable.

Added HD3SS3220 Type-C port controller along with Type-c connector for
controlling vbus supply.

Signed-off-by: Swati Agarwal <swati.agarwal@oss.qualcomm.com>
---
This patch depends on:
https://lore.kernel.org/all/20251128102507.3206169-1-krishna.kurapati@oss.qualcomm.com/
---
 arch/arm64/boot/dts/qcom/lemans-evk.dts | 102 ++++++++++++++++++++++++++++++++
 1 file changed, 102 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
index 2536ebe36edbfd146e07d5698779767acff87ab4..07389593b3cd4728357255d47156c6861cbabb5e 100644
--- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
+++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
@@ -67,6 +67,34 @@ usb0_con_ss_ep: endpoint {
 		};
 	};
 
+	connector-1 {
+		compatible = "usb-c-connector";
+		label = "USB1-Type-C";
+		data-role = "dual";
+		power-role = "dual";
+
+		vbus-supply = <&vbus_supply_regulator_1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				usb1_con_hs_ep: endpoint {
+				};
+			};
+			port@1 {
+				reg = <1>;
+
+				usb1_con_ss_ep: endpoint {
+					remote-endpoint = <&hd3ss3220_47_in_ep>;
+				};
+			};
+		};
+	};
+
 	edp0-connector {
 		compatible = "dp-connector";
 		label = "EDP0";
@@ -140,6 +168,16 @@ vbus_supply_regulator_0: regulator-vbus-supply-0 {
 		enable-active-high;
 	};
 
+	vbus_supply_regulator_1: vbus-supply-regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_supply_1";
+		gpio = <&expander1 3 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+	};
+
 	vmmc_sdc: regulator-vmmc-sdc {
 		compatible = "regulator-fixed";
 
@@ -527,6 +565,36 @@ hd3ss3220_out_ep: endpoint {
 			};
 		};
 	};
+
+	usb-typec@47 {
+		compatible = "ti,hd3ss3220";
+		reg = <0x47>;
+		interrupts-extended = <&pmm8654au_2_gpios 6 IRQ_TYPE_EDGE_FALLING>;
+		id-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&usb1_id>, <&usb1_intr_state>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hd3ss3220_47_in_ep: endpoint {
+					remote-endpoint = <&usb1_con_ss_ep>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				hd3ss3220_47_out_ep: endpoint {
+				};
+			};
+		};
+	};
+
 };
 
 &i2c18 {
@@ -690,6 +758,14 @@ usb0_intr_state: usb0-intr-state {
 		bias-pull-up;
 		power-source = <0>;
 	};
+
+	usb1_intr_state: usb1-intr-state {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		power-source = <0>;
+	};
 };
 
 &qup_i2c19_default {
@@ -849,6 +925,12 @@ usb_id: usb-id-state {
 		function = "gpio";
 		bias-pull-up;
 	};
+
+	usb1_id: usb1-id-state {
+		pins = "gpio51";
+		function = "gpio";
+		bias-pull-up;
+	};
 };
 
 &uart10 {
@@ -903,6 +985,26 @@ &usb_0_qmpphy {
 	status = "okay";
 };
 
+&usb_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vreg_l7a>;
+	vdda18-supply = <&vreg_l6c>;
+	vdda33-supply = <&vreg_l9a>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l1c>;
+	vdda-pll-supply = <&vreg_l7a>;
+
+	status = "okay";
+};
+
 &xo_board_clk {
 	clock-frequency = <38400000>;
 };

---
base-commit: 9371fd3173173c0e128e869ab7101bd971a36b1e
change-id: 20251128-swati-65461d354617

Best regards,
-- 
Swati Agarwal <swati.agarwal@oss.qualcomm.com>