[PATCH v2 4/6] gpio: aspeed-sgpio: Convert IRQ functions to use llops callbacks

[Billy Tsai <billy_tsai@aspeedtech.com>]

Update aspeed_sgpio_irq_handler() and aspeed_sgpio_setup_irqs() to use
the llops callbacks for register access instead of direct iowrite32().
This creates a unified hardware access layer, which is essential for
supporting SoCs with different register layouts like the AST2700.

Additionally, change the loop bounds to use ngpio instead of the static
ARRAY_SIZE(aspeed_sgpio_banks). This allows the driver to adapt to the
actual number of supported pins on the running SoC.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
---
 drivers/gpio/gpio-aspeed-sgpio.c | 22 ++++++++++------------
 1 file changed, 10 insertions(+), 12 deletions(-)

diff --git a/drivers/gpio/gpio-aspeed-sgpio.c b/drivers/gpio/gpio-aspeed-sgpio.c
index 33a830ea7d28..b5270e11b153 100644
--- a/drivers/gpio/gpio-aspeed-sgpio.c
+++ b/drivers/gpio/gpio-aspeed-sgpio.c
@@ -319,12 +319,13 @@ static void aspeed_sgpio_irq_handler(struct irq_desc *desc)
 	struct gpio_chip *gc = irq_desc_get_handler_data(desc);
 	struct irq_chip *ic = irq_desc_get_chip(desc);
 	struct aspeed_sgpio *data = gpiochip_get_data(gc);
-	unsigned int i, p;
+	unsigned int i, p, banks;
 	unsigned long reg;
 
 	chained_irq_enter(ic, desc);
 
-	for (i = 0; i < ARRAY_SIZE(aspeed_sgpio_banks); i++) {
+	banks = DIV_ROUND_UP(gc->ngpio, 64);
+	for (i = 0; i < banks; i++) {
 		reg = data->pdata->llops->reg_bank_get(data, i << 6, reg_irq_status);
 
 		for_each_set_bit(p, &reg, 32)
@@ -355,7 +356,6 @@ static int aspeed_sgpio_setup_irqs(struct aspeed_sgpio *gpio,
 				   struct platform_device *pdev)
 {
 	int rc, i;
-	const struct aspeed_sgpio_bank *bank;
 	struct gpio_irq_chip *irq;
 
 	rc = platform_get_irq(pdev, 0);
@@ -365,12 +365,11 @@ static int aspeed_sgpio_setup_irqs(struct aspeed_sgpio *gpio,
 	gpio->irq = rc;
 
 	/* Disable IRQ and clear Interrupt status registers for all SGPIO Pins. */
-	for (i = 0; i < ARRAY_SIZE(aspeed_sgpio_banks); i++) {
-		bank =  &aspeed_sgpio_banks[i];
+	for (i = 0; i < gpio->chip.ngpio; i += 2) {
 		/* disable irq enable bits */
-		iowrite32(0x00000000, bank_reg(gpio, bank, reg_irq_enable));
+		gpio->pdata->llops->reg_bit_set(gpio, i, reg_irq_enable, 0);
 		/* clear status bits */
-		iowrite32(0xffffffff, bank_reg(gpio, bank, reg_irq_status));
+		gpio->pdata->llops->reg_bit_set(gpio, i, reg_irq_status, 1);
 	}
 
 	irq = &gpio->chip.irq;
@@ -384,14 +383,13 @@ static int aspeed_sgpio_setup_irqs(struct aspeed_sgpio *gpio,
 	irq->num_parents = 1;
 
 	/* Apply default IRQ settings */
-	for (i = 0; i < ARRAY_SIZE(aspeed_sgpio_banks); i++) {
-		bank =  &aspeed_sgpio_banks[i];
+	for (i = 0; i < gpio->chip.ngpio; i += 2) {
 		/* set falling or level-low irq */
-		iowrite32(0x00000000, bank_reg(gpio, bank, reg_irq_type0));
+		gpio->pdata->llops->reg_bit_set(gpio, i, reg_irq_type0, 0);
 		/* trigger type is edge */
-		iowrite32(0x00000000, bank_reg(gpio, bank, reg_irq_type1));
+		gpio->pdata->llops->reg_bit_set(gpio, i, reg_irq_type1, 0);
 		/* single edge trigger */
-		iowrite32(0x00000000, bank_reg(gpio, bank, reg_irq_type2));
+		gpio->pdata->llops->reg_bit_set(gpio, i, reg_irq_type2, 0);
 	}
 
 	return 0;

-- 
2.34.1