[PATCH v5 4/4] arm64: dts: qcom: Add base PURWA-IOT-EVK board

[YijieYang <yijie.yang@oss.qualcomm.com>]

From: Yijie Yang <yijie.yang@oss.qualcomm.com>

The PURWA-IOT-EVK is an evaluation platform for IoT products, composed of
the Purwa IoT SoM and a carrier board. Together, they form a complete
embedded system capable of booting to UART.

PURWA-IOT-EVK uses the PS8833 as a retimer for USB0, unlike HAMOA-IOT-EVK.
Meanwhile, USB0 bypasses the SBU selector FSUSB42.

Make the following peripherals on the carrier board enabled:
- UART
- On-board regulators
- USB Type-C mux
- Pinctrl
- Embedded USB (EUSB) repeaters
- NVMe
- pmic-glink
- USB DisplayPorts
- Bluetooth
- WLAN
- Audio
- PCIe ports for PCIe3 through PCIe6a
- TPM

Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |  1 +
 .../{hamoa-iot-evk.dts => purwa-iot-evk.dts}  | 92 +++++++++++++------
 2 files changed, 65 insertions(+), 28 deletions(-)
 copy arch/arm64/boot/dts/qcom/{hamoa-iot-evk.dts => purwa-iot-evk.dts} (95%)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f80b5d9cf1e8..d42296ed302e 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -130,6 +130,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-lilac.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-maple.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-poplar.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-xiaomi-sagit.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= purwa-iot-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-fairphone-fp5.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-particle-tachyon.dtb
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/purwa-iot-evk.dts
similarity index 95%
copy from arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
copy to arch/arm64/boot/dts/qcom/purwa-iot-evk.dts
index 2390648a248f..fe539b1f4567 100644
--- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
+++ b/arch/arm64/boot/dts/qcom/purwa-iot-evk.dts
@@ -6,12 +6,12 @@
 /dts-v1/;
 
 #include <dt-bindings/leds/common.h>
-#include "hamoa-iot-som.dtsi"
+#include "purwa-iot-som.dtsi"
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
 / {
-	model = "Qualcomm Technologies, Inc. Hamoa IoT EVK";
-	compatible = "qcom,hamoa-iot-evk", "qcom,hamoa-iot-som", "qcom,x1e80100";
+	model = "Qualcomm Technologies, Inc. Purwa IoT EVK";
+	compatible = "qcom,purwa-iot-evk", "qcom,purwa-iot-som", "qcom,x1p42100";
 	chassis-type = "embedded";
 
 	aliases {
@@ -118,15 +118,15 @@ port@1 {
 					reg = <1>;
 
 					pmic_glink_ss0_ss_in: endpoint {
-						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+						remote-endpoint = <&retimer_ss0_ss_out>;
 					};
 				};
 
 				port@2 {
 					reg = <2>;
 
-					pmic_glink_ss0_sbu: endpoint {
-						remote-endpoint = <&usb_1_ss0_sbu_mux>;
+					pmic_glink_ss0_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss0_con_sbu_out>;
 					};
 				};
 			};
@@ -618,25 +618,6 @@ platform {
 		};
 	};
 
-	usb-1-ss0-sbu-mux {
-		compatible = "onnn,fsusb42", "gpio-sbu-mux";
-
-		enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>;
-		select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>;
-
-		pinctrl-0 = <&usb_1_ss0_sbu_default>;
-		pinctrl-names = "default";
-
-		mode-switch;
-		orientation-switch;
-
-		port {
-			usb_1_ss0_sbu_mux: endpoint {
-				remote-endpoint = <&pmic_glink_ss0_sbu>;
-			};
-		};
-	};
-
 	wcn7850-pmu {
 		compatible = "qcom,wcn7850-pmu";
 
@@ -753,6 +734,63 @@ retimer_ss2_con_sbu_out: endpoint {
 	};
 };
 
+&i2c3 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x8>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK4>;
+
+		vdd-supply = <&vreg_rtmr0_1p15>;
+		vdd33-supply = <&vreg_rtmr0_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+		vddar-supply = <&vreg_rtmr0_1p15>;
+		vddat-supply = <&vreg_rtmr0_1p15>;
+		vddio-supply = <&vreg_rtmr0_1p8>;
+
+		reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr0_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss0_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss0_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss0_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
 &i2c5 {
 	clock-frequency = <400000>;
 
@@ -1102,9 +1140,7 @@ edp_bl_reg_en: edp-bl-reg-en-state {
 		pins = "gpio10";
 		function = "normal";
 	};
-};
 
-&pmc8380_3_gpios {
 	pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state {
 		pins = "gpio8";
 		function = "normal";
@@ -1470,7 +1506,7 @@ &usb_1_ss0_hsphy {
 };
 
 &usb_1_ss0_qmpphy_out {
-	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+	remote-endpoint = <&retimer_ss0_ss_in>;
 };
 
 &usb_1_ss1_dwc3_hs {
-- 
2.34.1