[PATCH v5 11/12] scsi: ufs: ufs-qcom: Implement vops apply_tx_eqtr_settings()

[Can Guo <can.guo@oss.qualcomm.com>]

On some platforms, when Host Software triggers TX Equalization Training,
HW does not take TX EQTR settings programmed in PA_TxEQTRSetting, instead
HW takes TX EQTR settings from PA_TxEQG1Setting. Implement vops
apply_tx_eqtr_setting() to work around it by programming TX EQTR settings
to PA_TxEQG1Setting during TX EQTR procedure.

Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Can Guo <can.guo@oss.qualcomm.com>
---
 drivers/ufs/host/ufs-qcom.c | 31 +++++++++++++++++++++++++++++++
 drivers/ufs/host/ufs-qcom.h |  2 ++
 2 files changed, 33 insertions(+)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index a0314cb55c7f..9abdeeee81f7 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -2816,6 +2816,26 @@ static int ufs_qcom_get_rx_fom(struct ufs_hba *hba,
 	return 0;
 }
 
+static int ufs_qcom_apply_tx_eqtr_settings(struct ufs_hba *hba,
+					   struct ufs_pa_layer_attr *pwr_mode,
+					   struct tx_eqtr_iter *h_iter,
+					   struct tx_eqtr_iter *d_iter)
+{
+	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
+	u32 setting = 0;
+	int lane;
+
+	if (host->hw_ver.major != 0x7 || host->hw_ver.minor > 0x1)
+		return 0;
+
+	for (lane = 0; lane < pwr_mode->lane_tx; lane++) {
+		setting |= TX_HS_PRESHOOT_BITS(lane, h_iter->preshoot);
+		setting |= TX_HS_DEEMPHASIS_BITS(lane, h_iter->deemphasis);
+	}
+
+	return ufshcd_dme_set(hba, UIC_ARG_MIB(PA_TXEQG1SETTING), setting);
+}
+
 static int ufs_qcom_tx_eqtr_notify(struct ufs_hba *hba,
 				   enum ufs_notify_change_status status,
 				   struct ufs_pa_layer_attr *pwr_mode)
@@ -2838,6 +2858,11 @@ static int ufs_qcom_tx_eqtr_notify(struct ufs_hba *hba,
 		return 0;
 
 	if (status == PRE_CHANGE) {
+		ret = ufshcd_dme_get(hba, UIC_ARG_MIB(PA_TXEQG1SETTING),
+				     &host->saved_tx_eq_g1_setting);
+		if (ret)
+			return ret;
+
 		/* PMC to target HS Gear. */
 		ret = ufshcd_change_power_mode(hba, pwr_mode,
 					       UFSHCD_PMC_POLICY_DONT_FORCE);
@@ -2845,6 +2870,11 @@ static int ufs_qcom_tx_eqtr_notify(struct ufs_hba *hba,
 			dev_err(hba->dev, "%s: Failed to PMC to target HS-G%u, Rate-%s: %d\n",
 				__func__, gear, ufs_hs_rate_to_str(rate), ret);
 	} else {
+		ret = ufshcd_dme_set(hba, UIC_ARG_MIB(PA_TXEQG1SETTING),
+				     host->saved_tx_eq_g1_setting);
+		if (ret)
+			return ret;
+
 		/* PMC back to HS-G1. */
 		ret = ufshcd_change_power_mode(hba, &pwr_mode_hs_g1,
 					       UFSHCD_PMC_POLICY_DONT_FORCE);
@@ -2887,6 +2917,7 @@ static const struct ufs_hba_variant_ops ufs_hba_qcom_vops = {
 	.config_esi		= ufs_qcom_config_esi,
 	.freq_to_gear_speed	= ufs_qcom_freq_to_gear_speed,
 	.get_rx_fom		= ufs_qcom_get_rx_fom,
+	.apply_tx_eqtr_settings	= ufs_qcom_apply_tx_eqtr_settings,
 	.tx_eqtr_notify		= ufs_qcom_tx_eqtr_notify,
 };
 
diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
index 7183d6b2c8bb..5d083331a7f4 100644
--- a/drivers/ufs/host/ufs-qcom.h
+++ b/drivers/ufs/host/ufs-qcom.h
@@ -348,6 +348,8 @@ struct ufs_qcom_host {
 	u32 phy_gear;
 
 	bool esi_enabled;
+
+	u32 saved_tx_eq_g1_setting;
 };
 
 struct ufs_qcom_drvdata {
-- 
2.34.1