From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
To: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Subject: [PATCH v3 11/11] arm64: dts: qcom: x1e80100-dell-inspiron14-7441: Switch on CAMSS RGB sensor
Date: Thu, 26 Mar 2026 10:27:48 +0000 [thread overview]
Message-ID: <20260326-x1e-camss-csi2-phy-dtsi-v3-11-1d5a9306116a@linaro.org> (raw)
In-Reply-To: <20260326-x1e-camss-csi2-phy-dtsi-v3-0-1d5a9306116a@linaro.org>
Inspiron14 has a ov02e10 sensor on CSIPHY4. Enable the list of dependencies
now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi | 61 +++++++++++++++++++++++++++++
1 file changed, 61 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi b/arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi
index bf04a12b16bc9..e31f69fa43854 100644
--- a/arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1-dell-thena.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/input/gpio-keys.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "hamoa-pmics.dtsi"
@@ -792,6 +793,66 @@ vreg_l3j_0p8: ldo3 {
};
};
+&camss {
+ status = "okay";
+
+ ports {
+ /*
+ * port0 => csiphy0
+ * port1 => csiphy1
+ * port2 => csiphy2
+ * port3 => csiphy4
+ */
+ port@3 {
+ camss_csiphy4_inep0: endpoint@0 {
+ clock-lanes = <7>;
+ data-lanes = <0 1>;
+ remote-endpoint = <&ov02e10_ep>;
+ };
+ };
+ };
+};
+
+&cci1 {
+ status = "okay";
+};
+
+&cci1_i2c1 {
+ camera@10 {
+ compatible = "ovti,ov02e10";
+ reg = <0x10>;
+
+ reset-gpios = <&tlmm 237 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cam_rgb_default>;
+
+ clocks = <&camcc CAM_CC_MCLK4_CLK>;
+ assigned-clocks = <&camcc CAM_CC_MCLK4_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ orientation = <0>; /* front facing */
+
+ avdd-supply = <&vreg_l7b_2p8>;
+ dvdd-supply = <&vreg_l7b_2p8>;
+ dovdd-supply = <&vreg_cam_1p8>;
+
+ port {
+ ov02e10_ep: endpoint {
+ data-lanes = <1 2>;
+ link-frequencies = /bits/ 64 <360000000>;
+ remote-endpoint = <&camss_csiphy4_inep0>;
+ };
+ };
+ };
+};
+
+&csiphy4 {
+ vdda-0p9-supply = <&vreg_l2c_0p8>;
+ vdda-1p2-supply = <&vreg_l1c_1p2>;
+
+ status = "okay";
+};
+
&i2c0 {
clock-frequency = <400000>;
--
2.52.0
next prev parent reply other threads:[~2026-03-26 10:27 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-03-26 10:27 [PATCH v3 00/11] arm64: dts: qcom: Add x1e/Hamoa camera DTSI Bryan O'Donoghue
2026-03-26 10:27 ` [PATCH v3 01/11] arm64: dts: qcom: x1e80100: Add CAMCC block definition Bryan O'Donoghue
2026-03-27 15:19 ` Abel Vesa
2026-03-26 10:27 ` [PATCH v3 02/11] arm64: dts: qcom: x1e80100: Add CCI definitions Bryan O'Donoghue
2026-03-27 15:16 ` Abel Vesa
2026-03-26 10:27 ` [PATCH v3 03/11] arm64: dts: qcom: x1e80100: Add CAMSS block definition Bryan O'Donoghue
2026-03-26 10:27 ` [PATCH v3 04/11] arm64: dts: qcom: x1e80100-crd: Add pm8010 CRD pmic,id=m regulators Bryan O'Donoghue
2026-03-26 10:27 ` [PATCH v3 05/11] arm64: dts: qcom: x1e80100-crd: Add ov08x40 RGB sensor on CSIPHY4 Bryan O'Donoghue
2026-03-26 10:27 ` [PATCH v3 06/11] arm64: dts: qcom: x1e80100-t14s: Add pm8010 camera PMIC with voltage levels for IR and RGB camera Bryan O'Donoghue
2026-03-28 1:39 ` Christopher Obbard
2026-03-26 10:27 ` [PATCH v3 07/11] arm64: dts: qcom: x1e80100-t14s: Add on ov02c10 RGB sensor on CSIPHY4 Bryan O'Donoghue
2026-03-28 1:39 ` Christopher Obbard
2026-03-26 10:27 ` [PATCH v3 08/11] arm64: dts: qcom: x1e80100-lenovo-yoga-slim7x: Add pm8010 camera PMIC with voltage levels for IR and RGB camera Bryan O'Donoghue
2026-03-26 10:27 ` [PATCH v3 09/11] arm64: dts: qcom: x1e80100-lenovo-yoga-slim7x: Add l7b_2p8 voltage regulator for " Bryan O'Donoghue
2026-03-26 10:27 ` [PATCH v3 10/11] arm64: dts: qcom: x1e80100-lenovo-yoga-slim7x: Add ov02c10 RGB sensor on CSIPHY4 Bryan O'Donoghue
2026-03-26 10:27 ` Bryan O'Donoghue [this message]
2026-07-08 14:56 ` [PATCH v3 00/11] arm64: dts: qcom: Add x1e/Hamoa camera DTSI Bjorn Andersson
2026-07-08 21:11 ` Bryan O'Donoghue
2026-07-08 21:33 ` Bryan O'Donoghue
2026-07-15 20:52 ` Bjorn Andersson
2026-07-17 22:16 ` Bjorn Andersson
2026-07-17 22:21 ` Bryan O'Donoghue
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260326-x1e-camss-csi2-phy-dtsi-v3-11-1d5a9306116a@linaro.org \
--to=bryan.odonoghue@linaro.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox