[PATCH v6 9/9] riscv: dts: spacemit: k1-musepi-pro: add SD card support with UHS modes

[Iker Pedrosa <ikerpedrosam@gmail.com>]

From: Trevor Gamblin <tgamblin@baylibre.com>

Update the Muse Pi Pro devicetree with SD card support to match what
was done for the OrangePi RV2 in [1]. More precisely:

- Enable sdhci0 controller with 4-bit bus width
- Configure card detect GPIO with inversion
- Connect vmmc-supply to buck4 for 3.3V card power
- Connect vqmmc-supply to aldo1 for 1.8V/3.3V I/O switching
- Add dual pinctrl states for voltage-dependent pin configuration
- Support UHS-I SDR25, SDR50, and SDR104 modes

[1] https://lore.kernel.org/linux-riscv/20260316-orangepi-sd-card-uhs-v3-0-aefd3b7832df@gmail.com/T/#

Signed-off-by: Trevor Gamblin <tgamblin@baylibre.com>
Signed-off-by: Iker Pedrosa <ikerpedrosam@gmail.com>
---
 arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts | 66 ++++++++++++++++++++++++++
 1 file changed, 66 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index 29e333b670cf0a5c4ed852668460db475b9c44cb..774a4640f06562b5632c510e8961e3d8f60a3b81 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -18,6 +18,24 @@ aliases {
 		ethernet0 = &eth0;
 		serial0 = &uart0;
 	};
+	reg_dc_in: dc-in-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_in_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_vcc_4v: vcc-4v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_4v";
+		regulator-min-microvolt = <4000000>;
+		regulator-max-microvolt = <4000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 
 	chosen {
 		stdout-path = "serial0";
@@ -77,3 +95,51 @@ &uart0 {
 	pinctrl-names = "default";
 	status = "okay";
 };
+
+&i2c8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c8_cfg>;
+	status = "okay";
+
+	pmic@41 {
+		compatible = "spacemit,p1";
+		reg = <0x41>;
+		interrupts = <64>;
+		vin-supply = <&reg_vcc_4v>;
+
+		regulators {
+			buck4: buck4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			aldo1: aldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&sdhci0 {
+	pinctrl-names = "default", "uhs";
+	pinctrl-0 = <&mmc1_cfg>;
+	pinctrl-1 = <&mmc1_uhs_cfg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio K1_GPIO(80) GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	cap-sd-highspeed;
+	vmmc-supply = <&buck4>;
+	vqmmc-supply = <&aldo1>;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};

-- 
2.53.0