From: Louis Sautier <sautier.louis@gmail.com>
To: Sathya Prakash <sathya.prakash@broadcom.com>,
Sreekanth Reddy <sreekanth.reddy@broadcom.com>,
Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>,
Ranjan Kumar <ranjan.kumar@broadcom.com>,
"James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>,
"Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Guenter Roeck <linux@roeck-us.net>,
MPT-FusionLinux.pdl@broadcom.com, linux-scsi@vger.kernel.org,
linux-hwmon@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2 0/2] scsi: mpt3sas: add hwmon support
Date: Mon, 18 May 2026 20:41:07 +0200 [thread overview]
Message-ID: <20260518184109.770185-1-sautier.louis@gmail.com> (raw)
Expose the IOC and board temperature sensors of LSI / Broadcom / Avago
SAS HBAs that bind to mpt3sas through the hwmon interface. The data
lives in MPI IO Unit Page 7.
The same fields are exposed by Broadcom's userspace tooling through
the /dev/mpt[23]ctl ioctl path (typically root-only): IOCTemperature
and BoardTemperature in lsiutil; ROC and Controller in storcli.
With this driver, sensors(1) shows them unprivileged:
$ sensors mpt3sas-pci-0200
mpt3sas-pci-0200
Adapter: PCI adapter
IOC: +42.0°C
v1 -> v2:
v1: https://lore.kernel.org/r/20260512214703.655633-1-sautier.louis@gmail.com
* Dropped misleading Documentation/hwmon/mpt3sas.rst.
* Dropped inaccurate concurrency-wait figure from Testing;
corrected empirical data is in the on-list discussion.
Testing
-------
Validated across three Broadcom SAS chip generations. None of the
cards had a board sensor present, so the testing only covers the
IOC channel:
* LSI 9500-8i / SAS3816, SAS-3:
- hwmon device registers as "mpt3sas" with only temp1 (IOC) exposed
- IOC reading matches `storcli /c0 show temperature` and
`lsiutil -p1 -a 25,2,0,0`
- rmmod / modprobe cycle goes through the explicit
unregister/register paths cleanly
* LSI 9305-24i / SAS3224, SAS-3: same behaviour.
* LSI 9211-4i / SAS2004, SAS-2: firmware reports both
*TemperatureUnits = NOT_PRESENT, no hwmon device registered
(graceful-skip path).
Not verified (no available hardware):
* Path with both IOC and board sensors present.
* Fahrenheit-units conversion.
* Sub-zero readings (signed-cast path).
Louis Sautier (2):
scsi: mpt3sas: add IO Unit Page 7 config accessor
scsi: mpt3sas: add hwmon support
drivers/scsi/mpt3sas/Kconfig | 9 ++
drivers/scsi/mpt3sas/Makefile | 2 +
drivers/scsi/mpt3sas/mpt3sas_base.h | 19 +++
drivers/scsi/mpt3sas/mpt3sas_config.c | 36 +++++
drivers/scsi/mpt3sas/mpt3sas_hwmon.c | 200 ++++++++++++++++++++++++++
drivers/scsi/mpt3sas/mpt3sas_scsih.c | 6 +
6 files changed, 272 insertions(+)
create mode 100644 drivers/scsi/mpt3sas/mpt3sas_hwmon.c
base-commit: 5d6919055dec134de3c40167a490f33c74c12581
--
2.54.0
next reply other threads:[~2026-05-18 18:41 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-18 18:41 Louis Sautier [this message]
2026-05-18 18:41 ` [PATCH v2 1/2] scsi: mpt3sas: add IO Unit Page 7 config accessor Louis Sautier
2026-05-18 18:41 ` [PATCH v2 2/2] scsi: mpt3sas: add hwmon support Louis Sautier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260518184109.770185-1-sautier.louis@gmail.com \
--to=sautier.louis@gmail.com \
--cc=James.Bottomley@HansenPartnership.com \
--cc=MPT-FusionLinux.pdl@broadcom.com \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=martin.petersen@oracle.com \
--cc=ranjan.kumar@broadcom.com \
--cc=sathya.prakash@broadcom.com \
--cc=sreekanth.reddy@broadcom.com \
--cc=suganath-prabu.subramani@broadcom.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®