[PATCH v5 2/2] iio: adc: ad_sigma_delta: fix clear_pending_event for registerless devices

[Radu Sabau via B4 Relay <devnull+radu.sabau.analog.com@kernel.org>]

From: Radu Sabau <radu.sabau@analog.com>

ad_sigma_delta_clear_pending_event() falls through to the status register
read path for devices with has_registers = false and no rdy_gpiod. For
such devices, ad_sd_read_reg() skips the address byte entirely and clocks
raw MISO bytes with no address phase — making it byte-for-byte identical
to reading conversion data. If a pending conversion result is present,
this partially consumes it and corrupts the data stream for the subsequent
ad_sd_read_reg() call in ad_sigma_delta_single_conversion().

Furthermore, with num_resetclks = 0 on these devices, data_read_len
evaluates to 0. If the clocked byte has bit 7 clear, pending_event is set
and the code attempts memset(data + 2, 0xff, 0 - 1), overflowing to
SIZE_MAX and corrupting the heap.

Fix by returning 0 immediately when neither rdy_gpiod nor has_registers
is set. This is safe for all current registerless devices: ad7191 and
ad7780 (with powerdown GPIO) are reset between conversions by CS
deassertion, so there is no stale result to drain; ad7780 (without
powerdown GPIO) and max11205 are continuously-converting and cycle ~DRDY
at the output data rate regardless of whether the previous result was
read, so the next falling edge fires naturally.

A future registerless device that holds ~DRDY asserted until data is read
would be broken by this early return and would require either
num_resetclks set or a rdy-gpio.

The same heap corruption is reachable on any device with rdy_gpiod set
but num_resetclks = 0: if the GPIO indicates a pending event, the drain
path executes memset(data + 2, 0xff, 0 - 1) regardless of has_registers.
Add an explicit data_read_len == 0 guard after the pending event check;
the stale result is then consumed by the first ad_sd_read_reg() call in
ad_sigma_delta_single_conversion().

Signed-off-by: Radu Sabau <radu.sabau@analog.com>
---
 drivers/iio/adc/ad_sigma_delta.c | 31 +++++++++++++++++++++++++++++--
 1 file changed, 29 insertions(+), 2 deletions(-)

diff --git a/drivers/iio/adc/ad_sigma_delta.c b/drivers/iio/adc/ad_sigma_delta.c
index 651ade67ad2e..1b410291da53 100644
--- a/drivers/iio/adc/ad_sigma_delta.c
+++ b/drivers/iio/adc/ad_sigma_delta.c
@@ -262,11 +262,25 @@ static int ad_sigma_delta_clear_pending_event(struct ad_sigma_delta *sigma_delta
 
 	/*
 	 * Read R̅D̅Y̅ pin (if possible) or status register to check if there is an
-	 * old event.
+	 * old event. For devices with neither an RDY GPIO nor registers,
+	 * ad_sd_read_reg() transmits no address byte and clocks raw MISO bytes,
+	 * which is indistinguishable from reading conversion data and would
+	 * partially consume a pending result. Skip the check for such devices.
+	 *
+	 * This is safe for all current registerless devices: ad7191 and ad7780
+	 * (with powerdown GPIO) are reset between conversions by CS deassertion,
+	 * so there is no stale result to drain; ad7780 (without powerdown GPIO)
+	 * and max11205 are continuously-converting and cycle ~DRDY at the output
+	 * data rate regardless of whether the previous result was read, so the
+	 * next falling edge fires naturally.
+	 *
+	 * A future registerless device that holds ~DRDY asserted until data is
+	 * read would be broken by this early return and would need either
+	 * num_resetclks set or a rdy-gpio.
 	 */
 	if (sigma_delta->rdy_gpiod) {
 		pending_event = gpiod_get_value(sigma_delta->rdy_gpiod);
-	} else {
+	} else if (sigma_delta->info->has_registers) {
 		unsigned int status_reg;
 
 		ret = ad_sd_read_reg(sigma_delta, AD_SD_REG_STATUS, 1, &status_reg);
@@ -274,11 +288,24 @@ static int ad_sigma_delta_clear_pending_event(struct ad_sigma_delta *sigma_delta
 			return ret;
 
 		pending_event = !(status_reg & AD_SD_REG_STATUS_RDY);
+	} else {
+		return 0;
 	}
 
 	if (!pending_event)
 		return 0;
 
+	/*
+	 * With num_resetclks = 0, data_read_len is 0 and the drain sequence
+	 * below would compute memset(data + 2, 0xff, 0 - 1), underflowing to
+	 * SIZE_MAX and corrupting the heap. There is no safe way to drain the
+	 * stale result without knowing the data register size; it will be
+	 * consumed by the first ad_sd_read_reg() call in
+	 * ad_sigma_delta_single_conversion().
+	 */
+	if (!data_read_len)
+		return 0;
+
 	/*
 	 * In general the size of the data register is unknown. It varies from
 	 * device to device, might be one byte longer if CONTROL.DATA_STATUS is

-- 
2.43.0