[PATCH v5 05/12] iio: dac: ad5686: add support for missing power supplies

[Rodrigo Alencar via B4 Relay <devnull+rodrigo.alencar.analog.com@kernel.org>]

From: Rodrigo Alencar <rodrigo.alencar@analog.com>

Get and enable regulators for vdd, vlogic and vref input power pins. Vdd
is the input power supply, while vlogic powers the digital side. vref is
replacing vcc, which is being deprecated, but still supported. The value
of vref_mv is checked so that a device without internal voltage reference
cannot proceed without an explicit supply. For correct operation, vdd and
vlogic are required, then devm_regulator_get_enable() is used so the
driver can still work without them by using the stub/dummy regulators.
Error report uses dev_err_probe(), which helps debugging an init issue.
A small delay is added after the regulators are enabled to consider for
the power-up time (4.5 us).

Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
---
 drivers/iio/dac/ad5686.c | 22 ++++++++++++++++++++--
 1 file changed, 20 insertions(+), 2 deletions(-)

diff --git a/drivers/iio/dac/ad5686.c b/drivers/iio/dac/ad5686.c
index 5840fda4b011..e2ebabca6887 100644
--- a/drivers/iio/dac/ad5686.c
+++ b/drivers/iio/dac/ad5686.c
@@ -8,6 +8,8 @@
 #include <linux/array_size.h>
 #include <linux/bitfield.h>
 #include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/dev_printk.h>
 #include <linux/errno.h>
 #include <linux/export.h>
 #include <linux/kstrtox.h>
@@ -484,12 +486,28 @@ int ad5686_probe(struct device *dev,
 	st->ops = ops;
 	st->chip_info = chip_info;
 
-	ret = devm_regulator_get_enable_read_voltage(dev, "vcc");
+	ret = devm_regulator_get_enable(dev, "vdd");
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to enable vdd supply\n");
+
+	ret = devm_regulator_get_enable(dev, "vlogic");
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to enable vlogic supply\n");
+
+	ret = devm_regulator_get_enable_read_voltage(dev, "vref");
+	if (ret == -ENODEV) /* vcc-supply is deprecated, but supported still */
+		ret = devm_regulator_get_enable_read_voltage(dev, "vcc");
 	if (ret < 0 && ret != -ENODEV)
-		return ret;
+		return dev_err_probe(dev, ret, "failed to read vref voltage\n");
 
 	st->use_internal_vref = ret == -ENODEV;
 	st->vref_mv = st->use_internal_vref ? st->chip_info->int_vref_mv : ret / 1000;
+	if (!st->vref_mv)
+		return dev_err_probe(dev, -EINVAL,
+				     "invalid or not provided vref voltage\n");
+
+	/* 4.5us power-up time: Datasheet Table 4: Timing Characteristics */
+	fsleep(5);
 
 	/* Initialize masks to all ones */
 	st->pwr_down_mask = ~0;

-- 
2.43.0