From: Stoyan Bogdanov <sbogdanov@baylibre.com>
To: jbrunet@baylibre.com, linux@roeck-us.net, robh@kernel.org,
krzk+dt@kernel.org, conor+dt@kernel.org, corbet@lwn.net,
skhan@linuxfoundation.org
Cc: linux-hwmon@vger.kernel.org, devicetree@vger.kernel.org,
linux-doc@vger.kernel.org, linux-kernel@vger.kernel.org,
Stoyan Bogdanov <sbogdanov@baylibre.com>
Subject: [PATCH v5 3/3] hwmon: (pmbus/tps25990): Add TPS1689 support
Date: Tue, 28 Jul 2026 04:58:48 +0300 [thread overview]
Message-ID: <20260728015857.193890-4-sbogdanov@baylibre.com> (raw)
In-Reply-To: <20260728015857.193890-1-sbogdanov@baylibre.com>
Extend the existing TPS25990 driver to support the TPS1689 eFuse,
as both devices share the same command interface and functionality.
Update the documentation to include TPS1689 support.
Signed-off-by: Stoyan Bogdanov <sbogdanov@baylibre.com>
---
Documentation/hwmon/tps25990.rst | 15 +++--
drivers/hwmon/pmbus/tps25990.c | 98 ++++++++++++++++++++++++++------
2 files changed, 92 insertions(+), 21 deletions(-)
diff --git a/Documentation/hwmon/tps25990.rst b/Documentation/hwmon/tps25990.rst
index 04faec780d26..e8bc9a550bda 100644
--- a/Documentation/hwmon/tps25990.rst
+++ b/Documentation/hwmon/tps25990.rst
@@ -9,26 +9,31 @@ Supported chips:
Prefix: 'tps25990'
- * Datasheet
+ Datasheet: Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps25990
- Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps25990
+ * TI TPS1689
+
+ Prefix: 'tps1689'
+
+ Datasheet: Publicly available at Texas Instruments website: https://www.ti.com/lit/gpn/tps1689
Author:
Jerome Brunet <jbrunet@baylibre.com>
+ Stoyan Bogdanov <sbogdanov@baylibre.com>
Description
-----------
-This driver implements support for TI TPS25990 eFuse.
+This driver implements support for TI TPS25990 and TI TPS1689 eFuse chips.
This is an integrated, high-current circuit protection and power
management device with PMBUS interface
-Device compliant with:
+Devices are compliant with:
- PMBus rev 1.3 interface.
-Device supports direct format for reading input voltages,
+Devices supports direct format for reading input voltages,
output voltage, input current, input power and temperature.
Due to the specificities of the chip, all history reset attributes
diff --git a/drivers/hwmon/pmbus/tps25990.c b/drivers/hwmon/pmbus/tps25990.c
index 490dcd2a5fa5..7e2991a85da1 100644
--- a/drivers/hwmon/pmbus/tps25990.c
+++ b/drivers/hwmon/pmbus/tps25990.c
@@ -48,6 +48,7 @@
PK_MIN_AVG_RST_MIN)
enum chips {
+ tps1689,
tps25990,
};
@@ -105,6 +106,8 @@ static int tps25990_mfr_write_protect_get(struct i2c_client *client)
static int tps25990_read_word_data(struct i2c_client *client,
int page, int phase, int reg)
{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct tps25990_data *data = container_of(info, struct tps25990_data, info);
int ret;
switch (reg) {
@@ -193,9 +196,11 @@ static int tps25990_read_word_data(struct i2c_client *client,
ret = pmbus_read_word_data(client, page, phase, reg);
if (ret < 0)
break;
- ret = DIV_ROUND_CLOSEST(ret * TPS25990_VIN_OVF_NUM,
- TPS25990_VIN_OVF_DIV);
- ret += TPS25990_VIN_OVF_OFF;
+ if (data->chip_id == tps25990) {
+ ret = DIV_ROUND_CLOSEST(ret * TPS25990_VIN_OVF_NUM,
+ TPS25990_VIN_OVF_DIV);
+ ret += TPS25990_VIN_OVF_OFF;
+ }
break;
case PMBUS_IIN_OC_FAULT_LIMIT:
@@ -207,9 +212,11 @@ static int tps25990_read_word_data(struct i2c_client *client,
ret = pmbus_read_byte_data(client, page, TPS25990_VIREF);
if (ret < 0)
break;
- ret = DIV_ROUND_CLOSEST(ret * TPS25990_IIN_OCF_NUM,
- TPS25990_IIN_OCF_DIV);
- ret += TPS25990_IIN_OCF_OFF;
+ if (data->chip_id == tps25990) {
+ ret = DIV_ROUND_CLOSEST(ret * TPS25990_IIN_OCF_NUM,
+ TPS25990_IIN_OCF_DIV);
+ ret += TPS25990_IIN_OCF_OFF;
+ }
break;
case PMBUS_VIRT_SAMPLES:
@@ -238,6 +245,8 @@ static int tps25990_read_word_data(struct i2c_client *client,
static int tps25990_write_word_data(struct i2c_client *client,
int page, int reg, u16 value)
{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct tps25990_data *data = container_of(info, struct tps25990_data, info);
int ret;
switch (reg) {
@@ -253,20 +262,23 @@ static int tps25990_write_word_data(struct i2c_client *client,
value = clamp_val(value, 0, 0xff);
ret = pmbus_write_word_data(client, page, reg, value);
break;
-
case PMBUS_VIN_OV_FAULT_LIMIT:
- value -= TPS25990_VIN_OVF_OFF;
- value = DIV_ROUND_CLOSEST(((unsigned int)value) * TPS25990_VIN_OVF_DIV,
- TPS25990_VIN_OVF_NUM);
- value = clamp_val(value, 0, 0xf);
+ if (data->chip_id == tps25990) {
+ value -= TPS25990_VIN_OVF_OFF;
+ value = DIV_ROUND_CLOSEST(((unsigned int)value) * TPS25990_VIN_OVF_DIV,
+ TPS25990_VIN_OVF_NUM);
+ value = clamp_val(value, 0, 0xf);
+ }
ret = pmbus_write_word_data(client, page, reg, value);
break;
case PMBUS_IIN_OC_FAULT_LIMIT:
- value -= TPS25990_IIN_OCF_OFF;
- value = DIV_ROUND_CLOSEST(((unsigned int)value) * TPS25990_IIN_OCF_DIV,
- TPS25990_IIN_OCF_NUM);
- value = clamp_val(value, 0, 0x3f);
+ if (data->chip_id == tps25990) {
+ value -= TPS25990_IIN_OCF_OFF;
+ value = DIV_ROUND_CLOSEST(((unsigned int)value) * TPS25990_IIN_OCF_DIV,
+ TPS25990_IIN_OCF_NUM);
+ value = clamp_val(value, 0, 0x3f);
+ }
ret = pmbus_write_byte_data(client, page, TPS25990_VIREF, value);
break;
@@ -347,6 +359,59 @@ static const struct regulator_desc tps25990_reg_desc[] = {
#endif
static struct pmbus_driver_info tps25990_base_info[] = {
+ [tps1689] = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = direct,
+ .m[PSC_VOLTAGE_IN] = 1166,
+ .b[PSC_VOLTAGE_IN] = 0,
+ .R[PSC_VOLTAGE_IN] = -2,
+ .format[PSC_VOLTAGE_OUT] = direct,
+ .m[PSC_VOLTAGE_OUT] = 1166,
+ .b[PSC_VOLTAGE_OUT] = 0,
+ .R[PSC_VOLTAGE_OUT] = -2,
+ .format[PSC_TEMPERATURE] = direct,
+ .m[PSC_TEMPERATURE] = 140,
+ .b[PSC_TEMPERATURE] = 32103,
+ .R[PSC_TEMPERATURE] = -2,
+ /*
+ * Current and Power measurement depends on the ohm value
+ * of Rimon. m is multiplied by 1000 below to have an integer
+ * and -3 is added to R to compensate.
+ */
+ .format[PSC_CURRENT_IN] = direct,
+ .m[PSC_CURRENT_IN] = 9548,
+ .b[PSC_CURRENT_IN] = 0,
+ .R[PSC_CURRENT_IN] = -6,
+ .format[PSC_CURRENT_OUT] = direct,
+ .m[PSC_CURRENT_OUT] = 24347,
+ .b[PSC_CURRENT_OUT] = 0,
+ .R[PSC_CURRENT_OUT] = -3,
+ .format[PSC_POWER] = direct,
+ .m[PSC_POWER] = 2775,
+ .b[PSC_POWER] = 0,
+ .R[PSC_POWER] = -4,
+ .func[0] = (PMBUS_HAVE_VIN |
+ PMBUS_HAVE_VOUT |
+ PMBUS_HAVE_VMON |
+ PMBUS_HAVE_IIN |
+ PMBUS_HAVE_PIN |
+ PMBUS_HAVE_TEMP |
+ PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_STATUS_IOUT |
+ PMBUS_HAVE_STATUS_INPUT |
+ PMBUS_HAVE_STATUS_TEMP |
+ PMBUS_HAVE_SAMPLES),
+
+ .read_word_data = tps25990_read_word_data,
+ .write_word_data = tps25990_write_word_data,
+ .read_byte_data = tps25990_read_byte_data,
+ .write_byte_data = tps25990_write_byte_data,
+
+#if IS_ENABLED(CONFIG_SENSORS_TPS25990_REGULATOR)
+ .reg_desc = tps25990_reg_desc,
+ .num_regulators = ARRAY_SIZE(tps25990_reg_desc),
+#endif
+ },
[tps25990] = {
.pages = 1,
.format[PSC_VOLTAGE_IN] = direct,
@@ -389,7 +454,6 @@ static struct pmbus_driver_info tps25990_base_info[] = {
.write_word_data = tps25990_write_word_data,
.read_byte_data = tps25990_read_byte_data,
.write_byte_data = tps25990_write_byte_data,
-
#if IS_ENABLED(CONFIG_SENSORS_TPS25990_REGULATOR)
.reg_desc = tps25990_reg_desc,
.num_regulators = ARRAY_SIZE(tps25990_reg_desc),
@@ -398,12 +462,14 @@ static struct pmbus_driver_info tps25990_base_info[] = {
};
static const struct i2c_device_id tps25990_i2c_id[] = {
+ { "tps1689", tps1689 },
{ "tps25990", tps25990 },
{}
};
MODULE_DEVICE_TABLE(i2c, tps25990_i2c_id);
static const struct of_device_id tps25990_of_match[] = {
+ { .compatible = "ti,tps1689", .data = (void *)tps1689 },
{ .compatible = "ti,tps25990", .data = (void *)tps25990 },
{}
};
--
2.43.0
next prev parent reply other threads:[~2026-07-28 1:59 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-07-28 1:58 [PATCH v5 0/3] Rework TPS25990 direct conversions and add " Stoyan Bogdanov
2026-07-28 1:58 ` [PATCH v5 1/3] hwmon: (pmbus/tps25990): Rework driver for multi-device support Stoyan Bogdanov
2026-07-28 1:58 ` [PATCH v5 2/3] dt-bindings: hwmon: pmbus/tps25990: Add TPS1689 Stoyan Bogdanov
2026-07-28 1:58 ` Stoyan Bogdanov [this message]
2026-07-28 4:11 ` [PATCH v5 3/3] hwmon: (pmbus/tps25990): Add TPS1689 support Guenter Roeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260728015857.193890-4-sbogdanov@baylibre.com \
--to=sbogdanov@baylibre.com \
--cc=conor+dt@kernel.org \
--cc=corbet@lwn.net \
--cc=devicetree@vger.kernel.org \
--cc=jbrunet@baylibre.com \
--cc=krzk+dt@kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=robh@kernel.org \
--cc=skhan@linuxfoundation.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®