mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
To: Andrew Lunn <andrew@lunn.ch>,
	Heiner Kallweit <hkallweit1@gmail.com>,
	"David S . Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>,
	Alexander Stein <alexander.stein@ew.tq-group.com>,
	netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
	donggeunyoo.kernel@gmail.com
Subject: [PATCH net] net: phy: dp83867: restore the LED polarity after a soft reset
Date: Tue,  8 Sep 2026 20:49:01 +0900	[thread overview]
Message-ID: <20260908114901.74637-1-donggeunyoo.kernel@gmail.com> (raw)

dp83867_led_polarity_set() programs the LEDCR2 polarity bit for a
DT-configured LED. It runs once, from phy_probe() via of_phy_leds().
Every phy_init_hw() afterwards (phy_attach_direct(), mdio_bus_phy_resume(),
and MAC drivers such as fec_main.c) calls .soft_reset first, and
dp83867_phy_reset() issues DP83867_SW_RESET, which restores register
defaults. config_init does not touch LEDCR2 and the requested value is
not cached, so a DT-configured LED polarity is lost from the first
attach onward.

The soft reset is the only path that clears LEDCR2, and phy_init_hw()
always follows it with config_init. Cache the requested bits and reapply
them from dp83867_config_init(). aqr_gen1_config_init() recovers from the
same reset the same way (61578f679378).

Fixes: 447b80a9330e ("net: phy: dp83867: Add support for active-low LEDs")
Assisted-by: Claude:claude-fable-5
Signed-off-by: Donggeun Yoo <donggeunyoo.kernel@gmail.com>
---
The soft-reset regression was flagged by an automated analysis of an
earlier posting of the active-high series. Compile-tested and
call-chain-traced only; I have no affected hardware.

 drivers/net/phy/dp83867.c | 22 +++++++++++++++++++---
 1 file changed, 19 insertions(+), 3 deletions(-)

diff --git a/drivers/net/phy/dp83867.c b/drivers/net/phy/dp83867.c
index 88255e92b4cd..c9c3b0062cc7 100644
--- a/drivers/net/phy/dp83867.c
+++ b/drivers/net/phy/dp83867.c
@@ -196,6 +196,8 @@ struct dp83867_private {
 	bool set_clk_output;
 	u32 clk_output_sel;
 	bool sgmii_ref_clk_en;
+	u16 led_polarity;
+	u16 led_polarity_mask;
 };
 
 static int dp83867_ack_interrupt(struct phy_device *phydev)
@@ -896,6 +898,15 @@ static int dp83867_config_init(struct phy_device *phydev)
 			       mask, val);
 	}
 
+	/* Restore the LED polarity dropped by the soft reset in phy_init_hw() */
+	if (dp83867->led_polarity_mask) {
+		ret = phy_modify(phydev, DP83867_LEDCR2,
+				 dp83867->led_polarity_mask,
+				 dp83867->led_polarity);
+		if (ret)
+			return ret;
+	}
+
 	return 0;
 }
 
@@ -1141,8 +1152,10 @@ static int dp83867_led_hw_control_get(struct phy_device *phydev, u8 index,
 static int dp83867_led_polarity_set(struct phy_device *phydev, int index,
 				    unsigned long modes)
 {
+	struct dp83867_private *dp83867 = phydev->priv;
+	u16 mask = DP83867_LED_POLARITY(index);
 	/* Default active high */
-	u16 polarity = DP83867_LED_POLARITY(index);
+	u16 polarity = mask;
 	u32 mode;
 
 	for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
@@ -1154,8 +1167,11 @@ static int dp83867_led_polarity_set(struct phy_device *phydev, int index,
 			return -EINVAL;
 		}
 	}
-	return phy_modify(phydev, DP83867_LEDCR2,
-			  DP83867_LED_POLARITY(index), polarity);
+
+	dp83867->led_polarity_mask |= mask;
+	dp83867->led_polarity = (dp83867->led_polarity & ~mask) | polarity;
+
+	return phy_modify(phydev, DP83867_LEDCR2, mask, polarity);
 }
 
 static unsigned int dp83867_inband_caps(struct phy_device *phydev,
-- 
2.53.0


             reply	other threads:[~2026-09-08 11:49 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-09-08 11:49 Donggeun Yoo [this message]
2026-09-08 14:14 ` Andrew Lunn
2026-09-08 22:59   ` Donggeun Yoo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260908114901.74637-1-donggeunyoo.kernel@gmail.com \
    --to=donggeunyoo.kernel@gmail.com \
    --cc=alexander.stein@ew.tq-group.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=hkallweit1@gmail.com \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®