[RFC PATCH v5 1/8] ALSA: usb: add RME Babyface Pro driver core (probe, PCM stream)

["Ismaïl Bahloul" <i.bahloul01@gmail.com>]

Minimal first step of the series: card lifecycle (probe/disconnect),
interrupt-URB PCM streaming, and the sample-rate/varispeed clock
mechanism the stream depends on. No mixer controls, front-panel
support, DSP EQ or suspend/resume yet - each is added by its own
later patch.

The sample rate is the family register (request 0x10, index 0x0030:
32k/44.1k/48k family) with SET_INTERFACE(5, alt) selecting the x1/x2/x4
speed on top of it; the 0x1B DDS quad is varispeed, a pitch ratio
applied independently of the family. A running stream now locks the
rate: a second client asking for a different one is refused at
hw_params rather than silently retuning the device out from under a
live stream, matching the vendor drivers' own behaviour.

Co-developed-by: David Fredman <davfre@gmail.com>
Signed-off-by: David Fredman <davfre@gmail.com>
Signed-off-by: Ismaïl Bahloul <i.bahloul01@gmail.com>
---
 MAINTAINERS                         |    6 +
 sound/usb/Kconfig                   |   20 +
 sound/usb/Makefile                  |    2 +-
 sound/usb/babyfacepro/Makefile      |    4 +
 sound/usb/babyfacepro/babyfacepro.c | 1200 +++++++++++++++++++++++++++
 sound/usb/babyfacepro/babyfacepro.h |  165 ++++
 6 files changed, 1396 insertions(+), 1 deletion(-)
 create mode 100644 sound/usb/babyfacepro/Makefile
 create mode 100644 sound/usb/babyfacepro/babyfacepro.c
 create mode 100644 sound/usb/babyfacepro/babyfacepro.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 207a6e2db..31ed00692 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -23828,6 +23828,12 @@ F:	include/dt-bindings/power/thead,th1520-power.h
 F:	include/dt-bindings/reset/thead,th1520-reset.h
 F:	include/linux/firmware/thead/thead,th1520-aon.h
 
+RME BABYFACE PRO DRIVER (PROPRIETARY MODE)
+M:	Ismaïl Bahloul <i.bahloul01@gmail.com>
+L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
+S:	Maintained
+F:	sound/usb/babyfacepro/
+
 RNBD BLOCK DRIVERS
 M:	Md. Haris Iqbal <haris.iqbal@ionos.com>
 M:	Jack Wang <jinpu.wang@ionos.com>
diff --git a/sound/usb/Kconfig b/sound/usb/Kconfig
index b4588915e..f58eedf3d 100644
--- a/sound/usb/Kconfig
+++ b/sound/usb/Kconfig
@@ -204,6 +204,26 @@ config SND_USB_AUDIO_QMI
 	  To compile this driver as a module, choose M here: the module
 	  will be called snd-usb-audio-qmi.
 
+config SND_USB_BABYFACE_PRO
+	tristate "RME Babyface Pro / Pro FS (proprietary mode)"
+	select SND_PCM
+	help
+	  Say Y here to include support for the RME Babyface Pro and
+	  Babyface Pro FS in their proprietary mode (VID 0x2a39,
+	  PID 0x3fc0).  The two models share the same USB IDs and
+	  descriptors and are handled identically.
+
+	  The proprietary mode streams PCM over interrupt endpoints
+	  (interface 5, ep 0x01/0x82) instead of the class-compliant
+	  isochronous path handled by snd-usb-audio, so this driver is
+	  standalone (snd-usb-caiaq-style interrupt streaming).  This
+	  first patch covers probe, disconnect and the PCM stream only;
+	  later patches in the series add the mixer, front panel and
+	  DSP EQ as standard ALSA controls.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called snd-usb-babyface-pro.
+
 source "sound/usb/line6/Kconfig"
 
 endif	# SND_USB
diff --git a/sound/usb/Makefile b/sound/usb/Makefile
index e62794a87..2f83f5881 100644
--- a/sound/usb/Makefile
+++ b/sound/usb/Makefile
@@ -35,5 +35,5 @@ obj-$(CONFIG_SND_USB_UA101) += snd-usbmidi-lib.o
 obj-$(CONFIG_SND_USB_USX2Y) += snd-usbmidi-lib.o
 obj-$(CONFIG_SND_USB_US122L) += snd-usbmidi-lib.o
 
-obj-$(CONFIG_SND) += misc/ usx2y/ caiaq/ 6fire/ hiface/ bcd2000/ qcom/
+obj-$(CONFIG_SND) += misc/ usx2y/ caiaq/ 6fire/ hiface/ bcd2000/ qcom/ babyfacepro/
 obj-$(CONFIG_SND_USB_LINE6)	+= line6/
diff --git a/sound/usb/babyfacepro/Makefile b/sound/usb/babyfacepro/Makefile
new file mode 100644
index 000000000..5adc6d474
--- /dev/null
+++ b/sound/usb/babyfacepro/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+snd-usb-babyface-pro-y := babyfacepro.o
+
+obj-$(CONFIG_SND_USB_BABYFACE_PRO) += snd-usb-babyface-pro.o
diff --git a/sound/usb/babyfacepro/babyfacepro.c b/sound/usb/babyfacepro/babyfacepro.c
new file mode 100644
index 000000000..2d71286e3
--- /dev/null
+++ b/sound/usb/babyfacepro/babyfacepro.c
@@ -0,0 +1,1200 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * RME Babyface Pro / Pro FS - proprietary-mode USB audio driver
+ *
+ * Core driver: USB vendor requests + cold init, interrupt-URB PCM
+ * streaming, and the card lifecycle (probe/disconnect/module entry).
+ * No mixer controls, front-panel support or suspend/resume yet - see
+ * babyfacepro.h and the cover letter for the rest of the series.
+ */
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/string.h>
+#include <linux/unaligned.h>
+#include <linux/usb.h>
+#include <linux/workqueue.h>
+#include <sound/core.h>
+#include <sound/initval.h>
+#include <sound/pcm.h>
+
+#include "babyfacepro.h"
+
+/* -- sample-rate / alt classes -------------------- */
+
+/* rate = family_base << (alt - 1): three rate families (32k / 44.1k /
+ * 48k), three interface speeds.  Measured on hardware, all nine rates,
+ * through the family register alone (2026-09-16).
+ *
+ * 64 kHz is the 32 kHz family at x2, not a 64 kHz base at x1.  Both clock
+ * 64 kHz at pitch 0, but a 64 kHz base on alt 1 needs 64000 x 56 B =
+ * 3584 kB/s, which is exactly alt 1's 448-byte packet ceiling: any
+ * positive varispeed then runs off the end of the bus, and the device
+ * delivers the mirrored rate instead (asked +5 %, got -5 %).  At x2 the
+ * frame is 40 B, so the same 64 kHz costs 2560 kB/s against a 5120 kB/s
+ * ceiling.  Same reasoning puts 128 kHz on alt 3 rather than alt 2.
+ */
+static const struct bf_rate bf_rates[] = {
+	{  32000, BF_ALT_1, 56,  8 },
+	{  44100, BF_ALT_1, 56,  8 },
+	{  48000, BF_ALT_1, 56,  8 },
+	{  64000, BF_ALT_2, 40, 16 },
+	{  88200, BF_ALT_2, 40, 16 },
+	{  96000, BF_ALT_2, 40, 16 },
+	{ 128000, BF_ALT_3, 32, 32 },
+	{ 176400, BF_ALT_3, 32, 32 },
+	{ 192000, BF_ALT_3, 32, 32 },
+};
+
+static const unsigned int bf_rate_list[ARRAY_SIZE(bf_rates)] = {
+	32000, 44100, 48000, 64000, 88200,
+	96000, 128000, 176400, 192000,
+};
+
+const struct snd_pcm_hw_constraint_list bf_rates_constraint = {
+	.count = ARRAY_SIZE(bf_rate_list),
+	.list = bf_rate_list,
+	.mask = 0,
+};
+
+const struct bf_rate *bf_rate_lookup(unsigned int rate)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(bf_rates); i++)
+		if (bf_rates[i].rate == rate)
+			return &bf_rates[i];
+	return NULL;
+}
+
+unsigned int bf_rate_family(const struct bf_rate *r)
+{
+	switch (r->rate >> (r->alt - 1)) {
+	case 32000:
+		return 0;
+	case 44100:
+		return 1;
+	default:
+		return 2;
+	}
+}
+
+/* -- vendor requests ----------------------- */
+
+/* Timeout for every vendor control transfer (ms). */
+#define BF_CTL_TIMEOUT		1000
+
+int bf_vendor_write(struct snd_usb_babyface *chip, u8 req, u16 val, u16 idx)
+{
+	return usb_control_msg_send(chip->dev, 0, req,
+				    USB_DIR_OUT | USB_TYPE_VENDOR |
+				    USB_RECIP_DEVICE,
+				    val, idx, NULL, 0, BF_CTL_TIMEOUT, GFP_KERNEL);
+}
+
+int bf_vendor_read(struct snd_usb_babyface *chip, u8 req, u16 idx, u8 *buf)
+{
+	return usb_control_msg_recv(chip->dev, 0, req,
+				    USB_DIR_IN | USB_TYPE_VENDOR |
+				    USB_RECIP_DEVICE,
+				    0, idx, buf, 4, BF_CTL_TIMEOUT, GFP_KERNEL);
+}
+
+/* Sends the BF_REG_KEEPALIVE_SETTINGS word (PROTOCOL.md: "keepalive
+ * 0x10 0x05CF wVal = host settings-state register" - a single shared
+ * word, not independent per-setting writes).  Hardcoded to Internal
+ * clock for now; the clock-source control and the chip->clock_optical
+ * bit it composes in land with a later patch in this series, at which
+ * point this grows the same way babyface_restore_state() does further
+ * down the series.
+ */
+int bf_settings_write(struct snd_usb_babyface *chip)
+{
+	return bf_vendor_write(chip, BF_REQ_KEEPALIVE, BF_SETTINGS_CLOCK_INTERNAL,
+			       BF_REG_KEEPALIVE_SETTINGS);
+}
+
+/* Set the sample rate: the family register.  The firmware derives its
+ * own DDS word from it; SET_INTERFACE(5, alt) (done in hw_params) is the
+ * x1/x2/x4 speed.  This is exactly what the RME Windows driver sends on
+ * a rate change (USBPcap, 2026-09-14, all fourteen changes): the family,
+ * then the settings word, nothing else.  Measured on this driver's
+ * target hardware for all nine rates with no quad in play (2026-09-16),
+ * and to -1 ppm at 44.1 kHz against an NTP-disciplined clock.
+ *
+ * An earlier version of this branch had this register and measured it as
+ * dead.  It was not: bf_cold_init()'s 0x0021 -> 0x05ff write is this
+ * same register (0x05ff = 0x05cf | 0x0030) hardcoded to the 48 kHz
+ * family, and it followed the write.  See bf_cold_init().
+ */
+int bf_clock_write(struct snd_usb_babyface *chip)
+{
+	const struct bf_rate *r = bf_rate_lookup(chip->rate);
+	int ret;
+
+	if (!r)
+		return -EINVAL;
+	ret = bf_vendor_write(chip, BF_REQ_KEEPALIVE,
+			      bf_rate_family(r) << 4, BF_REG_RATE_FAMILY);
+	if (ret < 0)
+		return ret;
+	return bf_settings_write(chip);
+}
+
+/* Varispeed: the 0x1B DDS quad.  It is a pitch RATIO applied on top of
+ * the family rate, not a clock, so it carries no base rate and is the
+ * same four words at every sample rate (measured 2026-09-16: a 48 kHz
+ * quad over the 44.1 kHz family gives 44.1 kHz; the same quad at +5 %
+ * gives 46305).  It is sticky: the device keeps the last ratio across
+ * family writes, so pitch 0 must send the x1.0 quad rather than nothing.
+ *
+ * Only bank 2 is read on the Babyface Pro (one bank at a time swapped
+ * between two quads: only bank 2 moved the clock).  It is the ratio's
+ * period as a 24-bit word, 1.0 = 2^14 x 25 MHz / 48000 = 8533333.33, and
+ * the firmware's constant is exact: sent exact it measures -1 ppm, sent
+ * as RME's own Q16-truncated word (0x8234d3) it measures +14 ppm.  So
+ * bank 2 is computed exactly.  Banks 0, 1 and 3 are sent as the RME
+ * host software computes them - bank 0 the x1.0 period 12800000 scaled
+ * by the pitch, banks 1 and 3 that value times fixed Q16 constants
+ * (0xb9c2, 0xa3d7), truncated - so that a unit which reads a different
+ * bank (the FS is not measured) sees exactly what Windows gives it.
+ * Together this reproduces the cold-plug capture's quad at pitch 0 in
+ * banks 0, 1 and 3, and improves on it in bank 2.
+ *
+ * Every quad must be followed by the settings keepalive or it does not
+ * apply.  pitch is in 0.1 % steps, -50..50.
+ */
+int bf_pitch_write(struct snd_usb_babyface *chip, int pitch)
+{
+	const u64 num0 = 12800000ULL * 1000;		/* bank 0: 12800000 / (1 + p) */
+	const u64 num2 = 409600000000000ULL;		/* bank 2: 4.096e11 * 1000 */
+	u32 den0 = 1000 + pitch;
+	u32 den2 = 48000 * den0;
+	u64 b0 = div_u64(num0 + den0 / 2, den0);
+	u64 b[4];
+	int k, ret;
+
+	b[0] = b0;
+	b[1] = (b0 * 47554) >> 16;
+	b[2] = div_u64(num2 + den2 / 2, den2);
+	b[3] = (b0 * 41943) >> 16;
+
+	for (k = 0; k < 4; k++) {
+		ret = bf_vendor_write(chip, BF_REQ_DDS, (b[k] >> 8) & 0xffff,
+				      ((b[k] & 0xff) << 8) | k);
+		if (ret < 0)
+			return ret;
+	}
+	return bf_settings_write(chip);
+}
+
+/* The cold-start session init (cap_coldplug.pcap), verbatim from the
+ * user-space reference (protocol::streaming_init).  Without it the
+ * firmware never validates a stream.
+ */
+int bf_cold_init(struct snd_usb_babyface *chip)
+{
+	const struct bf_rate *r;
+	int ret, i;
+
+	for (i = 0; i <= 0x3d; i++) {
+		if (i == 0x1e || i == 0x1f)
+			continue;
+		ret = bf_vendor_write(chip, BF_REQ_REG_CLEAR, 0x0000, i);
+		if (ret < 0)
+			return ret;
+	}
+	/* The varispeed quad, where the coldplug capture sends its x1.0
+	 * quad.  At pitch 0 banks 0, 1 and 3 match the capture; bank 2 is
+	 * the exact ratio (see bf_pitch_write).
+	 */
+	ret = bf_pitch_write(chip, chip->pitch);
+	if (ret < 0)
+		return ret;
+	/* 0x1C status - the hardware-validated reference (protocol::
+	 * streaming_init) sends it as an OUT write; Windows reads it.
+	 * Both are tolerated; match the validated path.
+	 */
+	ret = bf_vendor_write(chip, BF_REQ_STATUS_2, 0x0000, 0x0000);
+	if (ret < 0)
+		return ret;
+	/* The settings word and the family register in one write (0x05ff =
+	 * 0x05cf | 0x0030).  The coldplug capture hardcodes 0x0021 here:
+	 * family 48 kHz, clock internal.  Sent for the rate actually in use,
+	 * this IS the rate write; hardcoded, it was the thing that reset every
+	 * earlier family write to 48 kHz.
+	 */
+	r = bf_rate_lookup(chip->rate);
+	if (!r)
+		return -EINVAL;
+	ret = bf_vendor_write(chip, BF_REQ_KEEPALIVE,
+			      (bf_rate_family(r) << 4) | BF_SETTINGS_CLOCK_INTERNAL,
+			      BF_REG_KEEPALIVE_INIT);
+	if (ret < 0)
+		return ret;
+	/* 0x17 wIdx=0x0000 does NOT touch the preamp state (0x003F). */
+	ret = bf_vendor_write(chip, BF_REQ_PREAMP, 0x000c, 0x0000);
+	if (ret < 0)
+		return ret;
+	ret = bf_vendor_write(chip, BF_REQ_PREAMP_COMMIT, 0x0000, 0x0000);
+	if (ret < 0)
+		return ret;
+	for (i = 0; i < 2; i++) {
+		ret = bf_vendor_write(chip, BF_REQ_KEEPALIVE, 0x0000, 0x3000);
+		if (ret < 0)
+			return ret;
+	}
+	for (i = 0; i < 3; i++) {
+		ret = bf_vendor_write(chip, BF_REQ_KEEPALIVE, 0x0800, 0x0800);
+		if (ret < 0)
+			return ret;
+	}
+	return 0;
+}
+
+/* -- PCM data path ------------------------- */
+
+static bool babyface_capture_copy(struct snd_usb_babyface *chip,
+				  struct snd_pcm_substream *subs,
+				  u8 *data, unsigned int frames)
+{
+	struct snd_pcm_runtime *rt = subs->runtime;
+	unsigned int buf_frames = rt->buffer_size;
+	unsigned int words = chip->frame_bytes / 4;
+	unsigned int chans = rt->channels;
+	unsigned int pos, f, i;
+	unsigned long new_period;
+	bool crossed = false;
+	u8 *dst;
+
+	spin_lock(&chip->lock);
+	pos = chip->hw_ptr[SNDRV_PCM_STREAM_CAPTURE] % buf_frames;
+	for (f = 0; f < frames; f++) {
+		const __le32 *w = (const __le32 *)(data + f * chip->frame_bytes);
+
+		dst = rt->dma_area + frames_to_bytes(rt, pos);
+		for (i = 0; i < chans; i++) {
+			/* Channel map: app ch0-3 = device words 0-3 (AN1-4);
+			 * app ch4-9 = words 6-11 (ADAT/SPDIF); app ch10/11 =
+			 * words 12/13 = a FIXED-GAIN playback tap (observed
+			 * 2026-08-25: the playback echoes there at ~-27 dB,
+			 * independent of the output masters - NOT the output
+			 * bus; the ADAT/SPDIF range is words 6-11 only).  The
+			 * device words 4/5 are a fixed marker, not audio -
+			 * skipped.  At 96/192 kHz the frame has fewer words;
+			 * missing ones read as zero.
+			 */
+			static const u8 map[12] = { 0, 1, 2, 3, 6, 7, 8, 9,
+						   10, 11, 12, 13 };
+			u8 wi = i < 12 ? map[i] : 0xff;
+			s32 s = 0;
+
+			if (wi < words) {
+				/* 24-bit sample in bits 31-8 of the 32-bit word;
+				 * S32_LE with 24 msbits, so copy the word as-is.
+				 */
+				s = (s32)le32_to_cpu(w[wi]);
+			}
+			put_unaligned_le32((u32)s, dst + i * 4);
+		}
+		pos++;
+		if (pos >= buf_frames)
+			pos = 0;
+	}
+	chip->hw_ptr[SNDRV_PCM_STREAM_CAPTURE] += frames;
+	new_period = chip->hw_ptr[SNDRV_PCM_STREAM_CAPTURE] / rt->period_size;
+	if (new_period != chip->prev_period[SNDRV_PCM_STREAM_CAPTURE]) {
+		chip->prev_period[SNDRV_PCM_STREAM_CAPTURE] = new_period;
+		crossed = true;
+	}
+	spin_unlock(&chip->lock);
+
+	return crossed;
+}
+
+static bool babyface_playback_copy(struct snd_usb_babyface *chip,
+				   struct snd_pcm_substream *subs,
+				   u8 *data, unsigned int frames)
+{
+	struct snd_pcm_runtime *rt = subs->runtime;
+	unsigned int buf_frames = rt->buffer_size;
+	unsigned int words = chip->frame_bytes / 4;
+	unsigned int chans = rt->channels;
+	unsigned int pos, f, i;
+	unsigned long new_period;
+	bool crossed = false;
+	const u8 *src;
+
+	spin_lock(&chip->lock);
+	/* Never copy frames the app has not prepared.  With several URBs in
+	 * flight the device can transiently be ahead of the app ring at low
+	 * periods, so hw_ptr may reach past appl_ptr; reading beyond appl_ptr
+	 * would trip a spurious XRUN.  The device just repeats the last
+	 * frames instead.  (Both counters are unbounded, so clamp on the
+	 * signed difference.)
+	 */
+	{
+		snd_pcm_sframes_t avail =
+			(snd_pcm_sframes_t)(rt->control->appl_ptr -
+					    chip->hw_ptr[SNDRV_PCM_STREAM_PLAYBACK]);
+
+		if (avail < 0)
+			avail = 0;
+		else if (avail > (snd_pcm_sframes_t)buf_frames)
+			avail = buf_frames;
+		if ((snd_pcm_uframes_t)avail < frames)
+			frames = (unsigned int)avail;
+	}
+	pos = chip->hw_ptr[SNDRV_PCM_STREAM_PLAYBACK] % buf_frames;
+	for (f = 0; f < frames; f++) {
+		__le32 *w = (__le32 *)(data + f * chip->frame_bytes);
+
+		src = rt->dma_area + frames_to_bytes(rt, pos);
+		/* App ch n feeds the device word n (PB1-6 = words 0-11);
+		 * words 12/13 stay zero.  At 96/192 kHz the frame is
+		 * shorter - the extra app channels are dropped.
+		 */
+		for (i = 0; i < chans && i < words; i++) {
+			u32 s = get_unaligned_le32(src + i * 4);
+
+			/* S32_LE msbits=24: the app's 24 valid bits are already
+			 * left-justified (bits 31-8) - copy the word as-is.
+			 */
+			w[i] = cpu_to_le32(s);
+		}
+		for (; i < words; i++)
+			w[i] = 0;
+		pos++;
+		if (pos >= buf_frames)
+			pos = 0;
+	}
+	chip->hw_ptr[SNDRV_PCM_STREAM_PLAYBACK] += frames;
+	new_period = chip->hw_ptr[SNDRV_PCM_STREAM_PLAYBACK] / rt->period_size;
+	if (new_period != chip->prev_period[SNDRV_PCM_STREAM_PLAYBACK]) {
+		chip->prev_period[SNDRV_PCM_STREAM_PLAYBACK] = new_period;
+		crossed = true;
+	}
+	spin_unlock(&chip->lock);
+
+	return crossed;
+}
+
+static void babyface_complete_in(struct urb *urb)
+{
+	struct snd_usb_babyface *chip = urb->context;
+	struct snd_pcm_substream *subs;
+	unsigned long flags;
+	unsigned int frames;
+	bool crossed = false;
+	int ret;
+
+	if (urb->status < 0) {
+		if (urb->status == -ESHUTDOWN || urb->status == -ENOENT ||
+		    urb->status == -ECONNRESET)
+			return;		/* killed */
+		dev_dbg_ratelimited(&chip->dev->dev, "IN urb status %d\n",
+				    urb->status);
+		if (atomic_inc_return(&chip->urb_err) >= BF_URB_ERR_STOP)
+			schedule_work(&chip->stream_work);
+		goto resubmit;
+	}
+	atomic_set(&chip->urb_err, 0);
+
+	subs = READ_ONCE(chip->subs[SNDRV_PCM_STREAM_CAPTURE]);
+	if (subs) {
+		snd_pcm_stream_lock_irqsave(subs, flags);
+		if (snd_pcm_running(subs)) {
+			frames = urb->actual_length / chip->frame_bytes;
+			if (frames)
+				crossed = babyface_capture_copy(chip, subs,
+								urb->transfer_buffer,
+								frames);
+		}
+		snd_pcm_stream_unlock_irqrestore(subs, flags);
+		if (crossed)
+			snd_pcm_period_elapsed(subs);
+	}
+resubmit:
+	ret = usb_submit_urb(urb, GFP_ATOMIC);
+	if (ret < 0) {
+		dev_err_ratelimited(&chip->dev->dev,
+				    "IN resubmit failed: %d\n", ret);
+		if (atomic_inc_return(&chip->urb_err) >= BF_URB_ERR_STOP)
+			schedule_work(&chip->stream_work);
+	}
+}
+
+static void babyface_complete_out(struct urb *urb)
+{
+	struct snd_usb_babyface *chip = urb->context;
+	struct snd_pcm_substream *subs;
+	unsigned long flags;
+	unsigned int frames;
+	bool crossed = false;
+	int ret;
+
+	if (urb->status < 0) {
+		if (urb->status == -ESHUTDOWN || urb->status == -ENOENT ||
+		    urb->status == -ECONNRESET)
+			return;		/* killed */
+		dev_dbg_ratelimited(&chip->dev->dev, "OUT urb status %d\n",
+				    urb->status);
+		if (atomic_inc_return(&chip->urb_err) >= BF_URB_ERR_STOP)
+			schedule_work(&chip->stream_work);
+		goto resubmit;
+	}
+	atomic_set(&chip->urb_err, 0);
+
+	subs = READ_ONCE(chip->subs[SNDRV_PCM_STREAM_PLAYBACK]);
+	if (subs) {
+		snd_pcm_stream_lock_irqsave(subs, flags);
+		if (snd_pcm_running(subs)) {
+			frames = chip->frames_per_urb;
+			crossed = babyface_playback_copy(chip, subs,
+							 urb->transfer_buffer, frames);
+		}
+		snd_pcm_stream_unlock_irqrestore(subs, flags);
+		if (crossed)
+			snd_pcm_period_elapsed(subs);
+	} else {
+		/* No consumer: silence the OUT frames. */
+		memset(urb->transfer_buffer, 0, urb->transfer_buffer_length);
+	}
+resubmit:
+	ret = usb_submit_urb(urb, GFP_ATOMIC);
+	if (ret < 0) {
+		dev_err_ratelimited(&chip->dev->dev,
+				    "OUT resubmit failed: %d\n", ret);
+		if (atomic_inc_return(&chip->urb_err) >= BF_URB_ERR_STOP)
+			schedule_work(&chip->stream_work);
+	}
+}
+
+void babyface_stream_kill(struct snd_usb_babyface *chip)
+{
+	int i;
+
+	for (i = 0; i < chip->nurbs; i++) {
+		usb_kill_urb(chip->urbs_in[i]);
+		usb_kill_urb(chip->urbs_out[i]);
+	}
+	chip->streaming = false;
+}
+
+/* Stream start/stop run in process context (control transfers sleep).
+ * The trigger only toggles stream_users and schedules this work.
+ */
+
+/* Stop both PCM substreams (if running) so apps blocked in read/write
+ * wake with a clean error: XRUN for a recoverable stream error, or
+ * DISCONNECTED when the card is going away.
+ */
+void babyface_pcm_stop_both(struct snd_usb_babyface *chip, snd_pcm_state_t state)
+{
+	int s;
+
+	for (s = 0; s < 2; s++) {
+		struct snd_pcm_substream *subs = READ_ONCE(chip->subs[s]);
+
+		if (subs && snd_pcm_running(subs))
+			snd_pcm_stop(subs, state);
+	}
+}
+
+/* Re-count stream_users from the substream running states.  The apps
+ * can recover (re-prepare + trigger) while the stream work runs, so a
+ * hard `= 0` would wipe a fresh increment and leave a RUNNING
+ * substream with no URBs (hang).  Called on the error paths with the
+ * mutex held.
+ */
+static void bf_recount_users(struct snd_usb_babyface *chip)
+{
+	unsigned long flags;
+	int s, users = 0;
+
+	for (s = 0; s < 2; s++) {
+		struct snd_pcm_substream *subs = READ_ONCE(chip->subs[s]);
+
+		if (subs && snd_pcm_running(subs))
+			users++;
+	}
+	spin_lock_irqsave(&chip->lock, flags);
+	chip->stream_users = users;
+	spin_unlock_irqrestore(&chip->lock, flags);
+}
+
+/* Stream model (big picture):
+ *
+ * The PCM stream is entirely asynchronous.  A trigger(START/STOP) does
+ * not touch the hardware; it only changes the shared stream_users
+ * counter (0..2, one per running substream, counted under chip->lock)
+ * and schedules stream_work.  The work runs in process context (the
+ * control transfers and usb_submit_urb() calls must sleep):
+ *
+ *  - 1st user (users 0 -> 1): cold-init + the session trigger pair,
+ *    then the interrupt URBs (nurbs in each direction) are submitted
+ *    and the session is armed.
+ *  - last user (users 1 -> 0): the URBs are killed and the session
+ *    disarmed.
+ *
+ * So the device has exactly one live stream regardless of how many
+ * substreams run, and a playback+capture pair shares it.  An app that
+ * triggers while the work is running just increments stream_users; the
+ * work's re-count on the error path (bf_recount_users) reflects the
+ * RUNNING state so a recovered app re-arms from a clean slate.
+ */
+void babyface_stream_work(struct work_struct *work)
+{
+	struct snd_usb_babyface *chip =
+		container_of(work, struct snd_usb_babyface, stream_work);
+	unsigned int urbsize;
+	unsigned long flags;
+	int i, ret;
+	int users;
+
+	mutex_lock(&chip->mutex);
+	urbsize = chip->frame_bytes * chip->frames_per_urb;
+
+	if (chip->shutdown) {
+		mutex_unlock(&chip->mutex);
+		return;
+	}
+
+	/* Persistent URB errors (bad link, device wedged): stop the stream
+	 * and wake the apps with -EPIPE.  stream_users is re-counted from
+	 * the (now stopped) substreams so an app recovery (prepare+start)
+	 * re-arms the session from a clean slate.
+	 */
+	if (atomic_read(&chip->urb_err) >= BF_URB_ERR_STOP) {
+		dev_err(&chip->dev->dev,
+			"stream error: %d consecutive bad URBs, stopping (apps re-arm)\n",
+			BF_URB_ERR_STOP);
+		babyface_pcm_stop_both(chip, SNDRV_PCM_STATE_XRUN);
+		if (chip->streaming)
+			babyface_stream_kill(chip);
+		bf_recount_users(chip);
+		atomic_set(&chip->urb_err, 0);
+		mutex_unlock(&chip->mutex);
+		return;
+	}
+
+	spin_lock_irqsave(&chip->lock, flags);
+	users = chip->stream_users;
+	spin_unlock_irqrestore(&chip->lock, flags);
+
+	if (users > 0 && !chip->streaming) {
+		/* The firmware only validates a stream session that is
+		 * preceded by the full cold-init (the user-space reference
+		 * sends streaming_init at every session start - without it
+		 * the outputs stay silent).
+		 */
+		ret = bf_cold_init(chip);
+		if (ret < 0)
+			goto err;
+
+		/* Stream trigger pair (cap_audio): 0x10 0x8000 + 0x1D. */
+		ret = bf_vendor_write(chip, BF_REQ_KEEPALIVE, 0x0000, 0x8000);
+		if (ret < 0)
+			goto err;
+		ret = bf_vendor_write(chip, BF_REQ_SESSION_START, 0x0000, 0x0000);
+		if (ret < 0)
+			goto err;
+
+		for (i = 0; i < chip->nurbs; i++) {
+			/* Do not replay data from the previous stream/format. */
+			memset(chip->buf_out[i], 0, urbsize);
+			usb_fill_int_urb(chip->urbs_in[i], chip->dev,
+					 usb_rcvintpipe(chip->dev, BF_EP_IN),
+					 chip->buf_in[i], urbsize,
+					 babyface_complete_in, chip, 1);
+			usb_fill_int_urb(chip->urbs_out[i], chip->dev,
+					 usb_sndintpipe(chip->dev, BF_EP_OUT),
+					 chip->buf_out[i], urbsize,
+					 babyface_complete_out, chip, 1);
+			/* The buffers come from usb_alloc_coherent(), so
+			 * they are already DMA-mapped: hand the HCD the
+			 * mapping instead of letting it map them again.
+			 * Without this, usb_hcd_map_urb_for_dma() calls
+			 * dma_map_single() on a coherent allocation, which
+			 * fails with -EAGAIN on any host where that
+			 * allocation is a vmap (IOMMU-backed dma-iommu,
+			 * e.g. amd_iommu in its default translated mode).
+			 */
+			chip->urbs_in[i]->transfer_dma = chip->dma_in[i];
+			chip->urbs_in[i]->transfer_flags |=
+				URB_NO_TRANSFER_DMA_MAP;
+			chip->urbs_out[i]->transfer_dma = chip->dma_out[i];
+			chip->urbs_out[i]->transfer_flags |=
+				URB_NO_TRANSFER_DMA_MAP;
+		}
+		for (i = 0; i < chip->nurbs; i++) {
+			ret = usb_submit_urb(chip->urbs_in[i], GFP_KERNEL);
+			if (ret < 0)
+				goto err;
+			ret = usb_submit_urb(chip->urbs_out[i], GFP_KERNEL);
+			if (ret < 0)
+				goto err;
+		}
+		/* Session arm (cap_audio frame 5829, after the URBs). */
+		ret = bf_vendor_write(chip, BF_REQ_SESSION_ARM, 0x0000, 0xc000);
+		if (ret < 0)
+			goto err;
+
+		chip->streaming = true;
+		dev_dbg(&chip->dev->dev, "stream started (%u frames/URB, %u URBs)\n",
+			chip->frames_per_urb, chip->nurbs);
+	} else if (users == 0 && chip->streaming) {
+		babyface_stream_kill(chip);
+		dev_dbg(&chip->dev->dev, "stream stopped\n");
+	}
+
+	mutex_unlock(&chip->mutex);
+	return;
+
+err:
+	dev_err(&chip->dev->dev, "failed to start stream: %d\n", ret);
+	babyface_stream_kill(chip);
+	/* The apps already got a successful trigger - wake them with an
+	 * XRUN so a failed start (device wedged, cold-init error) does not
+	 * leave them hung in read/write with no URBs in flight.
+	 */
+	babyface_pcm_stop_both(chip, SNDRV_PCM_STATE_XRUN);
+	bf_recount_users(chip);
+	mutex_unlock(&chip->mutex);
+}
+
+/* -- PCM --------------------------- */
+
+static const struct snd_pcm_hardware babyface_pcm_hw = {
+	.info = SNDRV_PCM_INFO_INTERLEAVED |
+		SNDRV_PCM_INFO_BLOCK_TRANSFER,
+	.formats = SNDRV_PCM_FMTBIT_S32_LE,
+	.rate_min = 32000,
+	.rate_max = 192000,
+	.channels_min = 2,
+	.channels_max = 12,
+	.buffer_bytes_max = 1 << 20,
+	.period_bytes_max = 1 << 18,
+	.periods_min = 2,
+	.periods_max = 16,
+};
+
+/* Is the OTHER direction actually transferring?  Not "is it open": a client
+ * that has the device open but has not started must still be able to pick the
+ * rate, so that an application opening playback and capture before starting
+ * either one can take both to 96 kHz.
+ */
+static bool bf_other_running(struct snd_usb_babyface *chip,
+			     struct snd_pcm_substream *subs)
+{
+	struct snd_pcm_substream *other = READ_ONCE(chip->subs[!subs->stream]);
+	unsigned long flags;
+	bool running;
+
+	if (!other)
+		return false;
+	snd_pcm_stream_lock_irqsave(other, flags);
+	running = snd_pcm_running(other);
+	snd_pcm_stream_unlock_irqrestore(other, flags);
+	return running;
+}
+
+static int babyface_pcm_open(struct snd_pcm_substream *subs)
+{
+	struct snd_usb_babyface *chip = snd_pcm_substream_chip(subs);
+	struct snd_pcm_runtime *rt = subs->runtime;
+	unsigned int locked;
+	unsigned long flags;
+	int ret;
+
+	rt->hw = babyface_pcm_hw;
+	ret = snd_pcm_hw_constraint_list(rt, 0, SNDRV_PCM_HW_PARAM_RATE,
+					 &bf_rates_constraint);
+	if (ret < 0)
+		return ret;
+	/* The stream is 24-bit audio in a 32-bit container, left-justified
+	 * (the device word carries the sample in bits 31-8).  Declare the
+	 * valid-bit width so user-space knows to ignore the low 8 bits.
+	 */
+	ret = snd_pcm_hw_constraint_msbits(rt, 0, 32, 24);
+	if (ret < 0)
+		return ret;
+	/* One URB delivers frames_per_urb frames per interrupt; a period must
+	 * span at least one URB so a completion crosses at most one period
+	 * boundary.  Constrain in frames (not bytes) so the minimum period
+	 * does not balloon at low channel counts: 2 ch @ 48 kHz -> 256
+	 * frames (5.3 ms) instead of 1536 frames from a 12-ch byte clamp.
+	 */
+	ret = snd_pcm_hw_constraint_minmax(rt, SNDRV_PCM_HW_PARAM_PERIOD_SIZE,
+					   chip->frames_per_urb, 1 << 18);
+	if (ret < 0)
+		return ret;
+
+	/* Both directions share one clock, so while audio is flowing the rate
+	 * belongs to whoever started it.  Offer that rate alone: a client
+	 * arriving later then negotiates down to it, and the sound server
+	 * resamples, rather than the device being retuned underneath a running
+	 * stream.  Advertising the constraint here rather than failing in
+	 * hw_params() is what keeps a PipeWire sink alive - it picks the rate
+	 * on offer instead of asking for one that has to be refused.
+	 *
+	 * This is what the vendor drivers do.  RME's settings panel greys the
+	 * sample rate out during record/playback, and their manual is explicit
+	 * that all active ASIO clients share one rate, with WDM (or CoreAudio)
+	 * doing any conversion - never the driver.
+	 */
+	mutex_lock(&chip->mutex);
+	locked = chip->streaming ? chip->rate : 0;
+	mutex_unlock(&chip->mutex);
+	if (locked) {
+		ret = snd_pcm_hw_constraint_minmax(rt, SNDRV_PCM_HW_PARAM_RATE,
+						   locked, locked);
+		if (ret < 0)
+			return ret;
+	}
+
+	spin_lock_irqsave(&chip->lock, flags);
+	chip->subs[subs->stream] = subs;
+	spin_unlock_irqrestore(&chip->lock, flags);
+	return 0;
+}
+
+static int babyface_pcm_close(struct snd_pcm_substream *subs)
+{
+	struct snd_usb_babyface *chip = snd_pcm_substream_chip(subs);
+	unsigned long flags;
+
+	/* Wait for the stream stop work so the URB callbacks (which
+	 * touch subs) are done before the substream can be freed.
+	 */
+	flush_work(&chip->stream_work);
+	spin_lock_irqsave(&chip->lock, flags);
+	chip->subs[subs->stream] = NULL;
+	spin_unlock_irqrestore(&chip->lock, flags);
+	return 0;
+}
+
+static int babyface_pcm_hw_params(struct snd_pcm_substream *subs,
+				  struct snd_pcm_hw_params *params)
+{
+	struct snd_usb_babyface *chip = snd_pcm_substream_chip(subs);
+	const struct bf_rate *r;
+	int ret = 0;
+
+	r = bf_rate_lookup(params_rate(params));
+	if (!r)
+		return -EINVAL;
+
+	/* The stream URBs must be at least one alt packet wide: the device
+	 * delivers its IN data in alt-sized packets (448/640/1024 B for
+	 * alt 1/2/3), and a smaller URB buffer makes the host controller
+	 * discard the transfer with -EOVERFLOW (babble) - seen at
+	 * 176.4/192 kHz with frames_per_urb below 32.  Return a clean
+	 * error instead of a silently dead capture stream.
+	 */
+	if (chip->frames_per_urb < r->min_fpu) {
+		dev_err(&chip->dev->dev,
+			"rate %u Hz needs frames_per_urb >= %u (module has %u)\n",
+			r->rate, r->min_fpu, chip->frames_per_urb);
+		return -EINVAL;
+	}
+
+	mutex_lock(&chip->mutex);
+	if (r->rate != chip->rate) {
+		/* The constraint in open() normally means nobody asks for a
+		 * rate other than the running one.  It can still happen, when
+		 * this substream was opened before the other one started: the
+		 * constraint is evaluated at open, so it did not apply then.
+		 * Refuse rather than retune - the alternative is a running
+		 * stream silently changing pitch, with no error and no xrun,
+		 * because a negotiated rate is never revised for a live
+		 * substream.
+		 */
+		if (bf_other_running(chip, subs)) {
+			dev_dbg(&chip->dev->dev,
+				"rate %u Hz refused: %u Hz stream running\n",
+				r->rate, chip->rate);
+			ret = -EBUSY;
+			goto out;
+		}
+		/* Nothing is transferring, so the clock is free.  Stop any
+		 * armed URBs, re-point the bandwidth class and let the stream
+		 * work restart the session at the new rate.
+		 */
+		if (chip->streaming)
+			babyface_stream_kill(chip);
+		ret = usb_set_interface(chip->dev, BF_IFACE, r->alt);
+		if (ret < 0) {
+			babyface_pcm_stop_both(chip, SNDRV_PCM_STATE_XRUN);
+			bf_recount_users(chip);
+			goto out;
+		}
+		chip->rate = r->rate;
+		chip->alt = r->alt;
+		chip->frame_bytes = r->frame_bytes;
+		/* Publish the new geometry before restarting either stream. */
+		schedule_work(&chip->stream_work);
+		dev_dbg(&chip->dev->dev, "rate %u Hz (alt %u)\n",
+			chip->rate, chip->alt);
+	}
+out:
+	mutex_unlock(&chip->mutex);
+	return ret;
+}
+
+static int babyface_pcm_hw_free(struct snd_pcm_substream *subs)
+{
+	/* The device buffer is host-side; nothing to release here. */
+	return 0;
+}
+
+static int babyface_pcm_prepare(struct snd_pcm_substream *subs)
+{
+	struct snd_usb_babyface *chip = snd_pcm_substream_chip(subs);
+	unsigned long flags;
+
+	spin_lock_irqsave(&chip->lock, flags);
+	chip->hw_ptr[subs->stream] = 0;
+	chip->prev_period[subs->stream] = 0;
+	spin_unlock_irqrestore(&chip->lock, flags);
+	return 0;
+}
+
+static int babyface_pcm_trigger(struct snd_pcm_substream *subs, int cmd)
+{
+	struct snd_usb_babyface *chip = snd_pcm_substream_chip(subs);
+	unsigned long flags;
+
+	switch (cmd) {
+	case SNDRV_PCM_TRIGGER_START:
+		spin_lock_irqsave(&chip->lock, flags);
+		chip->hw_ptr[subs->stream] = 0;
+		chip->prev_period[subs->stream] = 0;
+		/* stream_users is shared by the two substreams (separate
+		 * locks) - serialize the ++/-- so a concurrent trigger on
+		 * the other direction can't lose an increment (which would
+		 * stop the stream while a substream still runs).
+		 */
+		if (chip->stream_users++ == 0)
+			schedule_work(&chip->stream_work);
+		spin_unlock_irqrestore(&chip->lock, flags);
+		return 0;
+	case SNDRV_PCM_TRIGGER_STOP:
+		spin_lock_irqsave(&chip->lock, flags);
+		if (chip->stream_users > 0 && --chip->stream_users == 0)
+			schedule_work(&chip->stream_work);
+		spin_unlock_irqrestore(&chip->lock, flags);
+		return 0;
+	}
+	return -EINVAL;
+}
+
+static snd_pcm_uframes_t babyface_pcm_pointer(struct snd_pcm_substream *subs)
+{
+	struct snd_usb_babyface *chip = snd_pcm_substream_chip(subs);
+	unsigned long flags;
+	snd_pcm_uframes_t pos;
+
+	spin_lock_irqsave(&chip->lock, flags);
+	pos = chip->hw_ptr[subs->stream] % subs->runtime->buffer_size;
+	spin_unlock_irqrestore(&chip->lock, flags);
+	return pos;
+}
+
+static const struct snd_pcm_ops babyface_pcm_ops = {
+	.open = babyface_pcm_open,
+	.close = babyface_pcm_close,
+	.ioctl = snd_pcm_lib_ioctl,
+	.hw_params = babyface_pcm_hw_params,
+	.hw_free = babyface_pcm_hw_free,
+	.prepare = babyface_pcm_prepare,
+	.trigger = babyface_pcm_trigger,
+	.pointer = babyface_pcm_pointer,
+};
+
+static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX;
+static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR;
+static int frames_per_urb = BF_FRAMES_PER_URB_DEFAULT;
+static int nurbs = BF_NURBS_DEFAULT;
+
+module_param_array(index, int, NULL, 0444);
+MODULE_PARM_DESC(index, "Index value for the Babyface Pro sound card.");
+module_param_array(id, charp, NULL, 0444);
+MODULE_PARM_DESC(id, "ID string for the Babyface Pro sound card.");
+module_param(frames_per_urb, int, 0644);
+MODULE_PARM_DESC(frames_per_urb, "Audio frames per URB, 8..1024 (16 = low-latency floor, 256 = default).");
+module_param(nurbs, int, 0644);
+MODULE_PARM_DESC(nurbs, "URBs in flight per direction, 1..16 (16 = low-latency).");
+
+/* -- USB driver ------------------------- */
+
+static void babyface_private_free(struct snd_card *card)
+{
+	struct snd_usb_babyface *chip = card->private_data;
+	unsigned int urbsize;
+	int i;
+
+	if (!chip)
+		return;
+
+	/* The URB arrays are NULL when the probe failed before allocating
+	 * them (snd_card_free runs private_free on any probe error).
+	 */
+	if (chip->urbs_in) {
+		urbsize = BF_WORDS_PER_FRAME * sizeof(u32) * chip->frames_per_urb;
+		for (i = 0; i < chip->nurbs; i++) {
+			if (chip->urbs_in[i]) {
+				usb_kill_urb(chip->urbs_in[i]);
+				usb_free_urb(chip->urbs_in[i]);
+			}
+			if (chip->urbs_out[i]) {
+				usb_kill_urb(chip->urbs_out[i]);
+				usb_free_urb(chip->urbs_out[i]);
+			}
+			usb_free_coherent(chip->dev, urbsize, chip->buf_in[i],
+					  chip->dma_in[i]);
+			usb_free_coherent(chip->dev, urbsize, chip->buf_out[i],
+					  chip->dma_out[i]);
+		}
+	}
+	kfree(chip->urbs_in);
+	kfree(chip->urbs_out);
+	kfree(chip->buf_in);
+	kfree(chip->buf_out);
+	kfree(chip->dma_in);
+	kfree(chip->dma_out);
+	usb_put_dev(chip->dev);
+}
+
+static int babyface_probe(struct usb_interface *intf,
+			  const struct usb_device_id *usb_id)
+{
+	struct usb_device *dev = interface_to_usbdev(intf);
+	struct snd_usb_babyface *chip;
+	struct snd_card *card;
+	struct snd_pcm *pcm;
+	unsigned int urbsize;
+	int i, err;
+
+	if (intf->cur_altsetting->desc.bInterfaceNumber != BF_IFACE) {
+		/* Only the proprietary audio interface is ours; the MIDI
+		 * (standard class) and bulk interfaces stay unclaimed so
+		 * snd-usb-audio can take the MIDI one.
+		 */
+		return -ENODEV;
+	}
+
+	err = snd_card_new(&intf->dev, index[0], id[0], THIS_MODULE,
+			   sizeof(*chip), &card);
+	if (err < 0) {
+		dev_err(&intf->dev, "snd_card_new failed: %d\n", err);
+		return err;
+	}
+	chip = card->private_data;
+	chip->card = card;
+
+	chip->dev = usb_get_dev(dev);
+	/* USB autosuspend is untested: nothing in this driver holds a PM
+	 * reference while streaming, so an autosuspend request could race
+	 * a live stream.  Disable it explicitly rather than ship an
+	 * untested code path - full autosuspend support (correct
+	 * autopm_get/put pairing around the stream) is a deliberate
+	 * follow-up, not an oversight.
+	 */
+	usb_disable_autosuspend(chip->dev);
+	chip->iface = intf;
+	chip->nurbs = clamp(nurbs, 1, 16);
+	chip->frames_per_urb = clamp(frames_per_urb, 8, 1024) & ~7;
+	chip->rate = 48000;
+	chip->alt = BF_ALT_1;
+	chip->frame_bytes = 56;
+	mutex_init(&chip->mutex);
+	spin_lock_init(&chip->lock);
+	atomic_set(&chip->urb_err, 0);
+	INIT_WORK(&chip->stream_work, babyface_stream_work);
+	chip->card->private_free = babyface_private_free;
+
+	/* Model-neutral on purpose.  The FS and the original (2015)
+	 * Babyface Pro share VID:PID 2a39:3fc0, report the same bcdDevice
+	 * and the same iProduct shape, and neither says "FS" anywhere, so
+	 * there is nothing to tell them apart at probe time - and the
+	 * driver is reported to work unmodified on both.  card->driver in
+	 * particular is what alsa-lib configs and UCM profiles match on,
+	 * so it has to be right before this reaches a released kernel.
+	 */
+	strscpy(chip->card->driver, "BabyfacePro",
+		sizeof(chip->card->driver));
+	strscpy(chip->card->shortname, "Babyface Pro",
+		sizeof(chip->card->shortname));
+	snprintf(chip->card->longname, sizeof(chip->card->longname),
+		 "RME Babyface Pro (proprietary mode) at %s",
+		 dev_name(&dev->dev));
+
+	/* If the id was not passed as a module option, derive it from the
+	 * shortname with the whitespace removed, the way snd-usb-caiaq
+	 * does.  Letting the core derive it instead yields the last word
+	 * of the shortname ("Pro"), which is no use as an hw: name.
+	 */
+	if (*chip->card->id == '\0') {
+		char cid[sizeof(chip->card->id)];
+		const char *c;
+		size_t len;
+
+		memset(cid, 0, sizeof(cid));
+		for (c = chip->card->shortname, len = 0;
+		     *c && len < sizeof(cid) - 1; c++)
+			if (*c != ' ')
+				cid[len++] = *c;
+		snd_card_set_id(chip->card, cid);
+	}
+	strscpy(chip->card->mixername, "Babyface Pro",
+		sizeof(chip->card->mixername));
+
+	/* alt 1 = the default 48-kHz bandwidth class. */
+	err = usb_set_interface(dev, BF_IFACE, BF_ALT_1);
+	if (err < 0) {
+		dev_err(&intf->dev, "usb_set_interface failed: %d\n", err);
+		goto error;
+	}
+
+	err = bf_cold_init(chip);
+	if (err < 0) {
+		dev_err(&intf->dev, "cold init failed: %d\n", err);
+		goto error;
+	}
+
+	/* Keep the allocation size independent of the active USB mode. */
+	urbsize = BF_WORDS_PER_FRAME * sizeof(u32) * chip->frames_per_urb;
+	chip->urbs_in = kcalloc(chip->nurbs, sizeof(*chip->urbs_in), GFP_KERNEL);
+	chip->urbs_out = kcalloc(chip->nurbs, sizeof(*chip->urbs_out), GFP_KERNEL);
+	chip->buf_in = kcalloc(chip->nurbs, sizeof(*chip->buf_in), GFP_KERNEL);
+	chip->buf_out = kcalloc(chip->nurbs, sizeof(*chip->buf_out), GFP_KERNEL);
+	chip->dma_in = kcalloc(chip->nurbs, sizeof(*chip->dma_in), GFP_KERNEL);
+	chip->dma_out = kcalloc(chip->nurbs, sizeof(*chip->dma_out), GFP_KERNEL);
+	if (!chip->urbs_in || !chip->urbs_out || !chip->buf_in ||
+	    !chip->buf_out || !chip->dma_in || !chip->dma_out)
+		goto error;
+
+	for (i = 0; i < chip->nurbs; i++) {
+		chip->urbs_in[i] = usb_alloc_urb(0, GFP_KERNEL);
+		chip->urbs_out[i] = usb_alloc_urb(0, GFP_KERNEL);
+		chip->buf_in[i] = usb_alloc_coherent(dev, urbsize, GFP_KERNEL,
+						     &chip->dma_in[i]);
+		chip->buf_out[i] = usb_alloc_coherent(dev, urbsize, GFP_KERNEL,
+						      &chip->dma_out[i]);
+		if (!chip->urbs_in[i] || !chip->urbs_out[i] ||
+		    !chip->buf_in[i] || !chip->buf_out[i])
+			goto error;
+	}
+
+	err = snd_pcm_new(chip->card, "Babyface Pro", 0, 1, 1, &pcm);
+	if (err < 0) {
+		dev_err(&intf->dev, "snd_pcm_new failed: %d\n", err);
+		goto error;
+	}
+	pcm->private_data = chip;
+	strscpy(pcm->name, "Babyface Pro", sizeof(pcm->name));
+	snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &babyface_pcm_ops);
+	snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &babyface_pcm_ops);
+
+	/* The PCM buffer is host-side (the URB callbacks copy in/out of
+	 * it); vmalloc is the standard choice for that.
+	 */
+	err = snd_pcm_set_managed_buffer_all(pcm, SNDRV_DMA_TYPE_VMALLOC,
+					     NULL, 0, 1 << 20);
+	if (err < 0) {
+		dev_err(&intf->dev, "buffer allocation failed: %d\n", err);
+		goto error;
+	}
+
+	err = snd_card_register(chip->card);
+	if (err < 0) {
+		dev_err(&intf->dev, "snd_card_register failed: %d\n", err);
+		goto error;
+	}
+
+	usb_set_intfdata(intf, chip);
+	dev_info(&intf->dev,
+		 "Babyface Pro: card %i, %u frames/URB, %u URBs/direction\n",
+		 chip->card->number, chip->frames_per_urb, chip->nurbs);
+	return 0;
+
+error:
+	usb_set_intfdata(intf, NULL);
+	/* Balance the probe()-time usb_disable_autosuspend(): disconnect()
+	 * is never called for a failed probe, so the disable would leak and
+	 * leave autosuspend off on this usb_device until a physical unplug.
+	 */
+	usb_enable_autosuspend(chip->dev);
+	snd_card_free(chip->card);
+	return err;
+}
+
+static void babyface_disconnect(struct usb_interface *intf)
+{
+	struct snd_usb_babyface *chip = usb_get_intfdata(intf);
+
+	if (!chip)
+		return;
+
+	/* Idempotence guard: a disconnect can race a re-probe (usbfs
+	 * detach/re-attach) - tear the card down exactly once.
+	 */
+	usb_set_intfdata(intf, NULL);
+	if (chip->shutdown)
+		return;
+
+	chip->shutdown = true;
+	cancel_work_sync(&chip->stream_work);
+	/* Balance the probe()-time usb_disable_autosuspend(): the usb_device
+	 * outlives this interface claim (a usbfs detach re-probes without
+	 * the physical device ever disconnecting), so leaving autosuspend
+	 * disabled here would wrongly affect whatever claims the device next.
+	 */
+	usb_enable_autosuspend(chip->dev);
+	/* Wake apps blocked in read/write: the card is going away. */
+	dev_info(&chip->dev->dev, "disconnect: stopping PCM substreams\n");
+	babyface_pcm_stop_both(chip, SNDRV_PCM_STATE_DISCONNECTED);
+	mutex_lock(&chip->mutex);
+	if (chip->streaming)
+		babyface_stream_kill(chip);
+	mutex_unlock(&chip->mutex);
+
+	snd_card_disconnect(chip->card);
+	/* NEVER snd_card_free() here: it blocks until the last user
+	 * closes the card, and an open client (e.g. PipeWire) deadlocks
+	 * the disconnect (seen live: pipewire stuck in snd_card_free,
+	 * D state).  free_when_closed frees on the last close.
+	 */
+	snd_card_free_when_closed(chip->card);
+}
+
+static const struct usb_device_id babyface_ids[] = {
+	{ USB_DEVICE(USB_VENDOR_RME, USB_PRODUCT_BABYFACE_PRO_FS) },
+	{ }
+};
+MODULE_DEVICE_TABLE(usb, babyface_ids);
+
+static struct usb_driver babyface_driver = {
+	.name = "snd-usb-babyface-pro",
+	.probe = babyface_probe,
+	.disconnect = babyface_disconnect,
+	.id_table = babyface_ids,
+};
+
+static int __init babyface_init(void)
+{
+	return usb_register(&babyface_driver);
+}
+
+static void __exit babyface_exit(void)
+{
+	usb_deregister(&babyface_driver);
+}
+
+module_init(babyface_init);
+module_exit(babyface_exit);
+
+MODULE_AUTHOR("Ismaïl Bahloul <i.bahloul01@gmail.com>");
+MODULE_DESCRIPTION("RME Babyface Pro / Pro FS (proprietary mode) USB audio driver");
+MODULE_LICENSE("GPL");
diff --git a/sound/usb/babyfacepro/babyfacepro.h b/sound/usb/babyfacepro/babyfacepro.h
new file mode 100644
index 000000000..de0353a59
--- /dev/null
+++ b/sound/usb/babyfacepro/babyfacepro.h
@@ -0,0 +1,165 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * RME Babyface Pro / Pro FS - proprietary-mode USB audio driver
+ *
+ * The Babyface Pro (and Pro FS) present two personalities on the USB
+ * bus: a class-compliant one (handled by snd-usb-audio) and a
+ * proprietary one (VID 0x2a39 / PID 0x3fc0) whose PCM stream runs on
+ * INTERRUPT endpoints (interface 5, ep 0x01 OUT / 0x82 IN).
+ * Isochronous transfers are rejected there with EINVAL, and
+ * snd-usb-audio has no interrupt-PCM path, so this driver is
+ * standalone (snd-usb-caiaq-style interrupt streaming) instead of an
+ * snd-usb-audio quirk.
+ *
+ * This file and babyfacepro.c cover the card lifecycle (probe,
+ * disconnect) and the PCM stream only - no mixer controls, no
+ * front-panel support, no suspend/resume yet.  Those are added by
+ * later patches in this series, each with its own register map and
+ * device-state additions; see the cover letter for the full series
+ * plan.
+ *
+ * The protocol (vendor requests + 14x32-bit frame layout) was
+ * reverse-engineered from Windows captures and validated on hardware -
+ * tools/usbdump/PROTOCOL.md in the driver's development repository is
+ * the authoritative reference.
+ *
+ * Stream notes (hardware-validated 2026-08):
+ *   - frames_per_urb is tunable 8..1024 (multiple of 8) but must be at
+ *     least one alt packet wide - the device delivers IN data in
+ *     alt-sized packets (448/640/1024 B for alt 1/2/3), smaller URBs
+ *     get -EOVERFLOW (babble).  So frames_per_urb >= 8/16/32 for
+ *     alt 1/2/3; the driver rejects violating rates in hw_params.
+ *   - The device only advances the stream while BOTH endpoints have a
+ *     pending URB - IN and OUT are always submitted as a pair.
+ *   - SET_INTERFACE(5, alt) selects single/double/quad speed and USB
+ *     packet capacity; the BASE rate is the family register (request
+ *     0x10, index 0x0030: 32k / 44.1k / 48k family), from which the
+ *     firmware derives its own DDS word.  Three families times three
+ *     speeds give all nine rates.  The 0x1B DDS quad is varispeed: a
+ *     pitch RATIO applied on top of the family rate, sticky until
+ *     rewritten, with the 48 kHz cold-plug quad meaning x1.0.  See
+ *     bf_clock_write / bf_pitch_write.
+ */
+
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/unaligned.h>
+#include <linux/usb.h>
+#include <linux/workqueue.h>
+#include <sound/core.h>
+#include <sound/initval.h>
+#include <sound/pcm.h>
+
+#define USB_VENDOR_RME			0x2a39
+#define USB_PRODUCT_BABYFACE_PRO_FS	0x3fc0
+
+/* The proprietary audio interface (interface 5, interrupt endpoints). */
+#define BF_IFACE			5
+#define BF_EP_OUT			0x01
+#define BF_EP_IN			0x82
+
+#define BF_ALT_1			1	/* x1: 32/44.1/48 kHz, 448-B packets */
+#define BF_ALT_2			2	/* x2: 64/88.2/96 kHz, 640-B packets */
+#define BF_ALT_3			3	/* x4: 128/176.4/192 kHz, 1024-B packets */
+
+/* Default stream geometry - conservative, matches the RME TotalMix
+ * 256-sample buffer.  Both are tunable via module params; the
+ * low-latency profile (validated) is frames_per_urb=16 nurbs=16.
+ */
+#define BF_FRAMES_PER_URB_DEFAULT	256
+#define BF_NURBS_DEFAULT		8
+
+#define BF_WORDS_PER_FRAME		14	/* 14 x 32-bit words per frame */
+
+/* Consecutive URB errors (CRC/babble/protocol or a failed resubmit)
+ * before the stream is stopped and the apps get a clean -EPIPE.
+ */
+#define BF_URB_ERR_STOP			3
+
+/* Vendor requests (bmRequestType 0x40, value in wValue, no data phase).
+ * Only the subset the core probe/PCM path needs; the mixer, front
+ * panel and DSP EQ patches each add their own as those features land.
+ */
+#define BF_REQ_KEEPALIVE		0x10	/* settings word / stream trigger */
+#define BF_REQ_REG_CLEAR		0x16	/* cold-init register clear */
+#define BF_REQ_PREAMP			0x17	/* 48V/PAD state + readback */
+#define BF_REQ_DDS			0x1b	/* clock quads */
+#define BF_REQ_STATUS_2			0x1c	/* read 4 B */
+#define BF_REQ_SESSION_START		0x1d
+#define BF_REQ_SESSION_ARM		0x14
+#define BF_REQ_PREAMP_COMMIT		0x21	/* commit after 0x17 */
+
+#define BF_REG_RATE_FAMILY		0x0030	/* family << 4 (bReq 0x10) */
+/* 0x05ff = 0x05cf | 0x0030: the settings word and the family register
+ * written together (measured 2026-09-16: bits 4-5 of the value land in
+ * the family register).  The cold-plug capture writes 0x0021 here, i.e.
+ * family 48 kHz + clock internal - which is why replaying it after a
+ * family write used to reset the rate to 48 kHz.
+ */
+#define BF_REG_KEEPALIVE_INIT		0x05ff
+#define BF_REG_KEEPALIVE_SETTINGS	0x05cf
+
+/* Host settings-state word carried by the BF_REG_KEEPALIVE_SETTINGS
+ * keepalive (PROTOCOL.md "keepalive 0x10 0x05CF wVal = host settings-
+ * state register", hardware-verified 2026-08-22/23).  Only the
+ * Internal value is used until the clock-source control lands with a
+ * later patch in this series.
+ */
+#define BF_SETTINGS_CLOCK_INTERNAL	0x0001
+#define BF_SETTINGS_CLOCK_OPTICAL	0x0004
+
+struct snd_usb_babyface {
+	struct snd_card *card;
+	struct usb_device *dev;
+	struct usb_interface *iface;
+
+	struct mutex mutex;		/* controls + stream geometry */
+	spinlock_t lock;		/* hw_ptr / subs */
+
+	/* stream */
+	struct urb **urbs_in;
+	struct urb **urbs_out;
+	void **buf_in;
+	void **buf_out;
+	dma_addr_t *dma_in;
+	dma_addr_t *dma_out;
+	unsigned int nurbs;
+	unsigned int frames_per_urb;
+	unsigned int frame_bytes;	/* 56/40/32 for alt 1/2/3 */
+	unsigned int rate;
+	unsigned int alt;
+	int pitch;			/* varispeed in 0.1% (-500..+500) */
+	int stream_users;		/* PCM substreams sharing the stream */
+	bool streaming;			/* URBs actually in flight */
+	bool shutdown;
+	atomic_t urb_err;		/* consecutive bad URBs (stops the stream) */
+	struct work_struct stream_work;
+
+	struct snd_pcm_substream *subs[2];
+	unsigned long hw_ptr[2];
+	unsigned long prev_period[2];
+};
+
+struct bf_rate {
+	unsigned int rate;
+	unsigned int alt;
+	unsigned int frame_bytes;
+	unsigned int min_fpu;	/* frames/URB floor = one alt packet (448/640/1024 B) */
+};
+
+/* -- babyfacepro.c ------------------------ */
+const struct bf_rate *bf_rate_lookup(unsigned int rate);
+/* The family register value for a rate: 0 / 1 / 2 for the 32k / 44.1k /
+ * 48k family (rate >> (alt - 1)).
+ */
+unsigned int bf_rate_family(const struct bf_rate *r);
+int bf_vendor_write(struct snd_usb_babyface *chip, u8 req, u16 val, u16 idx);
+int bf_vendor_read(struct snd_usb_babyface *chip, u8 req, u16 idx, u8 *buf);
+int bf_settings_write(struct snd_usb_babyface *chip);
+int bf_clock_write(struct snd_usb_babyface *chip);
+int bf_pitch_write(struct snd_usb_babyface *chip, int pitch);
+int bf_cold_init(struct snd_usb_babyface *chip);
+void babyface_stream_kill(struct snd_usb_babyface *chip);
+void babyface_pcm_stop_both(struct snd_usb_babyface *chip, snd_pcm_state_t state);
+void babyface_stream_work(struct work_struct *work);
+extern const struct snd_pcm_hw_constraint_list bf_rates_constraint;
-- 
2.55.0