[PATCH v3 07/14] drm/bridge: analogix_dp: Use platform-specific HPD detection scheme

[Damon Ding <damon.ding@rock-chips.com>]

The Analogix DP controller provides two sets of interrupt sources for
hotplug detection: HOTPLUG_CHG for any HPD level change, and the
PLUG/HPD_LOST pair for connect/disconnect transitions respectively.

On Rockchip platforms, configure the HPD deglitch filter and use
HOTPLUG_CHG interrupt for hotplug detection. Other platforms retain the
original PLUG + HPD_LOST scheme with unchanged deglitch values.

Move the HPD deglitch configuration into analogix_dp_reset() so that
platform-specific values are set alongside the existing register
defaults in a single location. Update the threaded IRQ handler to check
the corresponding interrupt flag based on platform type.

Signed-off-by: Damon Ding <damon.ding@rock-chips.com>

---

Changes in v2:
- Move ANALOGIX_DP_HPD_DEGLITCH_L/ANALOGIX_DP_HPD_DEGLITCH_H configs to
  analogix_dp_reset().

Changes in v3:
- Modify the commit msg.
- Replace macro HPD_IRQ with HPD_IRQ_ALL.
---
 .../drm/bridge/analogix/analogix_dp_core.c    |  9 ++++++--
 .../gpu/drm/bridge/analogix/analogix_dp_reg.c | 22 ++++++++++++++++---
 2 files changed, 26 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index f88e3263ba0e..287fc16125ef 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -714,13 +714,18 @@ static irqreturn_t analogix_dp_irq_thread(int irq, void *arg)
 {
 	struct analogix_dp_device *dp = arg;
 	u32 irq_type;
+	bool hpd_detected;
 
 	irq_type = analogix_dp_get_irq_type(dp);
 	if (irq_type)
 		analogix_dp_clear_hotplug_interrupts(dp, irq_type);
 
-	if (irq_type & DP_IRQ_TYPE_HP_CABLE_IN ||
-	    irq_type & DP_IRQ_TYPE_HP_CABLE_OUT) {
+	if (!dp->hpd_gpiod && analogix_dp_is_rockchip(dp->plat_data->dev_type))
+		hpd_detected = irq_type & DP_IRQ_TYPE_HP_CHANGE;
+	else
+		hpd_detected = (irq_type & DP_IRQ_TYPE_HP_CABLE_IN) ||
+			       (irq_type & DP_IRQ_TYPE_HP_CABLE_OUT);
+	if (hpd_detected) {
 		dev_dbg(dp->dev, "Detected cable status changed!\n");
 		if (dp->drm_dev)
 			drm_helper_hpd_irq_event(dp->drm_dev);
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index 0f1406e4a5d3..025da25463a8 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -160,8 +160,13 @@ void analogix_dp_reset(struct analogix_dp_device *dp)
 	writel(0x0, dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL);
 	writel(0x0, dp->reg_base + ANALOGIX_DP_HDCP_CTL);
 
-	writel(0x5e, dp->reg_base + ANALOGIX_DP_HPD_DEGLITCH_L);
-	writel(0x1a, dp->reg_base + ANALOGIX_DP_HPD_DEGLITCH_H);
+	if (analogix_dp_is_rockchip(dp->plat_data->dev_type)) {
+		writel(0x80, dp->reg_base + ANALOGIX_DP_HPD_DEGLITCH_L);
+		writel(0xbb, dp->reg_base + ANALOGIX_DP_HPD_DEGLITCH_H);
+	} else {
+		writel(0x5e, dp->reg_base + ANALOGIX_DP_HPD_DEGLITCH_L);
+		writel(0x1a, dp->reg_base + ANALOGIX_DP_HPD_DEGLITCH_H);
+	}
 
 	writel(0x10, dp->reg_base + ANALOGIX_DP_LINK_DEBUG_CTL);
 
@@ -188,7 +193,18 @@ void analogix_dp_config_interrupt(struct analogix_dp_device *dp)
 	writel(0, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_2);
 	writel(0, dp->reg_base + ANALOGIX_DP_COMMON_INT_MASK_3);
 
-	analogix_dp_unmute_hpd_interrupt(dp, HPD_IRQ_ALL);
+	/*
+	 * Either HOTPLUG_CHG interrupt or PLUG + HPD_LOST interrupt
+	 * pair can be used to implement hotplug detection.
+	 *
+	 * On Rockchip platforms, configuring HPD deglitch to 2ms and
+	 * using HOTPLUG_CHG interrupt for hotplug detection is proven
+	 * as a better solution via engineering verification.
+	 */
+	if (analogix_dp_is_rockchip(dp->plat_data->dev_type))
+		analogix_dp_unmute_hpd_interrupt(dp, DP_IRQ_TYPE_HP_CHANGE);
+	else
+		analogix_dp_unmute_hpd_interrupt(dp, HPD_IRQ_ALL);
 }
 
 /*
-- 
2.34.1