[PATCH] power: supply: qcom_smbx: set the charge enable after software control

[Fabricio Akio via B4 Relay <devnull+fabricioakio.gmail.com@kernel.org>]

From: Fabricio Akio <fabricioakio@gmail.com>

The init sequence sets CHARGING_ENABLE_CMD before CHGR_CFG2 selects
software control of the charge enable.

The Motorola Moto X4's bootloader leaves the charger watchdog armed to
disable charging when it bites, which it does after a few minutes in
fastboot. Charging then stays disabled in the next boot until the cable
is replugged. Setting the command after CHGR_CFG2 re-enables it.

Fixes: 8648aeb5d7b7 ("power: supply: add Qualcomm PMI8998 SMB2 Charger driver")
Cc: stable@vger.kernel.org
Signed-off-by: Fabricio Akio <fabricioakio@gmail.com>
---
Tested on a Motorola Moto X4 (XT1900-6, SDM630 with PM660) with the
sdm660-mainline 7.2.3 tree. After the bootloader's charger watchdog had
bitten, in a boot without this driver or after three to five minutes in
fastboot, the charger stayed in DISABLE_CHARGE without this patch. With
it, charging resumed with no cable replug: 0.7 A into the battery at
89%. Other boards are untested.

Robin Snyders' pending SMB5 series renames smb_init_seq[], so whichever
of the two lands second needs a trivial rebase. Applies unchanged to
next-20261001.
---
 drivers/power/supply/qcom_smbx.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/power/supply/qcom_smbx.c b/drivers/power/supply/qcom_smbx.c
index f5557b8cc92a..8c6b7c46b85f 100644
--- a/drivers/power/supply/qcom_smbx.c
+++ b/drivers/power/supply/qcom_smbx.c
@@ -819,11 +819,7 @@ static const struct smb_init_register smb_init_seq[] = {
 	  .mask = SOC_LT_CHG_RECHARGE_THRESH_SEL_BIT |
 		  VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT,
 	  .val = VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT },
-	/* Enable charging */
 	{ .addr = USBIN_OPTIONS_1_CFG, .mask = HVDCP_EN_BIT, .val = 0 },
-	{ .addr = CHARGING_ENABLE_CMD,
-	  .mask = CHARGING_ENABLE_CMD_BIT,
-	  .val = CHARGING_ENABLE_CMD_BIT },
 	/*
 	 * Match downstream defaults
 	 * CHG_EN_SRC_BIT - charger enable is controlled by software
@@ -844,6 +840,13 @@ static const struct smb_init_register smb_init_seq[] = {
 		  AUTO_RECHG_BIT | EN_ANALOG_DROP_IN_VBATT_BIT |
 		  CHARGER_INHIBIT_BIT,
 	  .val = CHARGER_INHIBIT_BIT },
+	/*
+	 * Set the enable command only once CHGR_CFG2 has selected software
+	 * control, or a charger its watchdog has disabled stays disabled.
+	 */
+	{ .addr = CHARGING_ENABLE_CMD,
+	  .mask = CHARGING_ENABLE_CMD_BIT,
+	  .val = CHARGING_ENABLE_CMD_BIT },
 	/* STAT pin software override, match downstream. Parallel charging? */
 	{ .addr = STAT_CFG,
 	  .mask = STAT_SW_OVERRIDE_CFG_BIT,

---
base-commit: 9f24d789f03b22941b905ded43cb5ff8eea9ce62
change-id: 20261002-qcom-smbx-enable-order-816788337f26

Best regards,
--  
Fabricio Akio <fabricioakio@gmail.com>