[RFC PATCH 5/6] arm64: dts: amlogic: t7: add the ethernet controller

[Lucas Tanure <tanure@linux.com>]

The SoC pairs a Synopsys gigabit MAC with a small block of glue
registers that selects the interface type and trims the clock timing,
and with a multiplexer that points the management bus at either the
on-chip 100M PHY or the external pins. None of it was described, so the
port could not be used at all.

Add the controller and the multiplexer. The MAC reports a 5.10a core.
The path the controller reaches memory over runs through a pipeline
stage with a gate of its own, so hand that to the controller as well;
nothing else claims it and it would otherwise be switched off as unused,
leaving the port unable to complete a transfer.

The on-chip PHY behind the second port of the multiplexer is described
the way the G12A does it. No board in tree uses it and that path is
untested.

The controller is left disabled for boards to enable.

Assisted-by: LLM
Signed-off-by: Lucas Tanure <tanure@linux.com>
---
 arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi | 57 +++++++++++++++++++++
 1 file changed, 57 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
index 7bd53ec16607..140f1836f3dd 100644
--- a/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
+++ b/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
@@ -250,6 +250,31 @@ gic: interrupt-controller@fff01000 {
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		ethmac: ethernet@fdc00000 {
+			compatible = "amlogic,t7-dwmac",
+				     "snps,dwmac-5.10a",
+				     "snps,dwmac";
+			reg = <0x0 0xfdc00000 0x0 0x10000>,
+			      <0x0 0xfe024000 0x0 0x8>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks = <&clkc_periphs CLKID_SYS_ETH>,
+				 <&scmi_clk CLKID_FCLK_DIV2>,
+				 <&mpll CLKID_MPLL2>,
+				 <&clkc_periphs CLKID_SYS_AMPIPE_ETH>;
+			clock-names = "stmmaceth", "clkin0", "clkin1", "pipeline";
+			power-domains = <&pwrc PWRC_T7_ETH_ID>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <2048>;
+			status = "disabled";
+
+			mdio0: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		apb4: bus@fe000000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xfe000000 0x0 0x480000>;
@@ -645,6 +670,38 @@ gpio_intc: interrupt-controller@4080 {
 					<10 11 12 13 14 15 16 17 18 19 20 21>;
 			};
 
+			eth_phy: mdio-multiplexer@28000 {
+				compatible = "amlogic,g12a-mdio-mux";
+				reg = <0x0 0x28000 0x0 0xa4>;
+				clocks = <&clkc_periphs CLKID_SYS_ETHPHY>,
+					 <&xtal>,
+					 <&scmi_clk CLKID_FCLK_50M>;
+				clock-names = "pclk", "clkin0", "clkin1";
+				mdio-parent-bus = <&mdio0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ext_mdio: mdio@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				int_mdio: mdio@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					internal_ephy: ethernet-phy@8 {
+						compatible = "ethernet-phy-id0180.3301",
+							     "ethernet-phy-ieee802.3-c22";
+						interrupts = <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>;
+						reg = <8>;
+						max-speed = <100>;
+					};
+				};
+			};
+
 			uart_a: serial@78000 {
 				compatible = "amlogic,t7-uart", "amlogic,meson-s4-uart";
 				reg = <0x0 0x78000 0x0 0x18>;
-- 
2.56.0