From: Antoine Pichot <antoine.pichot@gmail.com>
To: linux-media@vger.kernel.org
Cc: sakari.ailus@linux.intel.com, mchehab@kernel.org,
djrscally@gmail.com, dan.scally@ideasonboard.com,
hansg@kernel.org, andriy.shevchenko@linux.intel.com,
linux-kernel@vger.kernel.org,
Antoine Pichot <antoine.pichot@gmail.com>
Subject: [PATCH 5/7] media: i2c: ov7251: Move the strobe registers out of the mode tables
Date: Mon, 26 Oct 2026 20:10:30 +0900 [thread overview]
Message-ID: <20261026111032.88355-6-antoine.pichot@gmail.com> (raw)
In-Reply-To: <20261026111032.88355-1-antoine.pichot@gmail.com>
The three mode tables write the same values to the STROBE pad output
enable bit (0x3005) and to the strobe control block (0x3b80-0x3b96).
Move these writes to a separate register array written right after the
mode table at stream start, and name the registers a following patch
needs: SC_REG5 (0x3005, whose bit 3 enables the STROBE pad output), the
strobe frame pattern (0x3b81) and the 32-bit strobe frame span (0x3b8c).
The values written are unchanged, only the order of the writes within
the stream start sequence changes. No functional change intended.
Signed-off-by: Antoine Pichot <antoine.pichot@gmail.com>
---
drivers/media/i2c/ov7251.c | 93 ++++++++++++++------------------------
1 file changed, 33 insertions(+), 60 deletions(-)
diff --git a/drivers/media/i2c/ov7251.c b/drivers/media/i2c/ov7251.c
index b6579a56a5..ad66422d9e 100644
--- a/drivers/media/i2c/ov7251.c
+++ b/drivers/media/i2c/ov7251.c
@@ -53,6 +53,9 @@
#define OV7251_PLL2_DIVIDER_REG 0x309d
#define OV7251_PLL2_SYS_DIV_REG 0x309a
#define OV7251_PLL2_ADC_DIV_REG 0x309b
+#define OV7251_SC_REG5 0x3005
+#define OV7251_STROBE_FRAME_PATTERN 0x3b81
+#define OV7251_STROBE_FRAME_SPAN 0x3b8c
#define OV7251_NATIVE_WIDTH 656
#define OV7251_NATIVE_HEIGHT 496
@@ -240,8 +243,31 @@ static const struct reg_value ov7251_global_init_setting[] = {
{ 0x303b, 0x02 },
};
+/* Strobe output settings, the same for all modes */
+static const struct reg_value ov7251_strobe_regs[] = {
+ { OV7251_SC_REG5, 0x00 },
+ { 0x3b80, 0x00 },
+ { OV7251_STROBE_FRAME_PATTERN, 0xa5 },
+ { 0x3b82, 0x10 },
+ { 0x3b83, 0x00 },
+ { 0x3b84, 0x08 },
+ { 0x3b85, 0x00 },
+ { 0x3b86, 0x01 },
+ { 0x3b87, 0x00 },
+ { 0x3b88, 0x00 },
+ { 0x3b89, 0x00 },
+ { 0x3b8a, 0x00 },
+ { 0x3b8b, 0x05 },
+ { OV7251_STROBE_FRAME_SPAN, 0x00 },
+ { 0x3b8d, 0x00 },
+ { 0x3b8e, 0x00 },
+ { 0x3b8f, 0x1a },
+ { 0x3b94, 0x05 },
+ { 0x3b95, 0xf2 },
+ { 0x3b96, 0x40 },
+};
+
static const struct reg_value ov7251_setting_vga_30fps[] = {
- { 0x3005, 0x00 },
{ 0x3012, 0xc0 },
{ 0x3013, 0xd2 },
{ 0x3014, 0x04 },
@@ -314,25 +340,6 @@ static const struct reg_value ov7251_setting_vga_30fps[] = {
{ 0x3834, 0x00 },
{ 0x3835, 0x0c },
{ 0x3837, 0x00 },
- { 0x3b80, 0x00 },
- { 0x3b81, 0xa5 },
- { 0x3b82, 0x10 },
- { 0x3b83, 0x00 },
- { 0x3b84, 0x08 },
- { 0x3b85, 0x00 },
- { 0x3b86, 0x01 },
- { 0x3b87, 0x00 },
- { 0x3b88, 0x00 },
- { 0x3b89, 0x00 },
- { 0x3b8a, 0x00 },
- { 0x3b8b, 0x05 },
- { 0x3b8c, 0x00 },
- { 0x3b8d, 0x00 },
- { 0x3b8e, 0x00 },
- { 0x3b8f, 0x1a },
- { 0x3b94, 0x05 },
- { 0x3b95, 0xf2 },
- { 0x3b96, 0x40 },
{ 0x3c00, 0x89 },
{ 0x3c01, 0x63 },
{ 0x3c02, 0x01 },
@@ -369,7 +376,6 @@ static const struct reg_value ov7251_setting_vga_30fps[] = {
};
static const struct reg_value ov7251_setting_vga_60fps[] = {
- { 0x3005, 0x00 },
{ 0x3012, 0xc0 },
{ 0x3013, 0xd2 },
{ 0x3014, 0x04 },
@@ -442,25 +448,6 @@ static const struct reg_value ov7251_setting_vga_60fps[] = {
{ 0x3834, 0x00 },
{ 0x3835, 0x0c },
{ 0x3837, 0x00 },
- { 0x3b80, 0x00 },
- { 0x3b81, 0xa5 },
- { 0x3b82, 0x10 },
- { 0x3b83, 0x00 },
- { 0x3b84, 0x08 },
- { 0x3b85, 0x00 },
- { 0x3b86, 0x01 },
- { 0x3b87, 0x00 },
- { 0x3b88, 0x00 },
- { 0x3b89, 0x00 },
- { 0x3b8a, 0x00 },
- { 0x3b8b, 0x05 },
- { 0x3b8c, 0x00 },
- { 0x3b8d, 0x00 },
- { 0x3b8e, 0x00 },
- { 0x3b8f, 0x1a },
- { 0x3b94, 0x05 },
- { 0x3b95, 0xf2 },
- { 0x3b96, 0x40 },
{ 0x3c00, 0x89 },
{ 0x3c01, 0x63 },
{ 0x3c02, 0x01 },
@@ -497,7 +484,6 @@ static const struct reg_value ov7251_setting_vga_60fps[] = {
};
static const struct reg_value ov7251_setting_vga_90fps[] = {
- { 0x3005, 0x00 },
{ 0x3012, 0xc0 },
{ 0x3013, 0xd2 },
{ 0x3014, 0x04 },
@@ -570,25 +556,6 @@ static const struct reg_value ov7251_setting_vga_90fps[] = {
{ 0x3834, 0x00 },
{ 0x3835, 0x0c },
{ 0x3837, 0x00 },
- { 0x3b80, 0x00 },
- { 0x3b81, 0xa5 },
- { 0x3b82, 0x10 },
- { 0x3b83, 0x00 },
- { 0x3b84, 0x08 },
- { 0x3b85, 0x00 },
- { 0x3b86, 0x01 },
- { 0x3b87, 0x00 },
- { 0x3b88, 0x00 },
- { 0x3b89, 0x00 },
- { 0x3b8a, 0x00 },
- { 0x3b8b, 0x05 },
- { 0x3b8c, 0x00 },
- { 0x3b8d, 0x00 },
- { 0x3b8e, 0x00 },
- { 0x3b8f, 0x1a },
- { 0x3b94, 0x05 },
- { 0x3b95, 0xf2 },
- { 0x3b96, 0x40 },
{ 0x3c00, 0x89 },
{ 0x3c01, 0x63 },
{ 0x3c02, 0x01 },
@@ -1369,6 +1336,12 @@ static int ov7251_s_stream(struct v4l2_subdev *subdev, int enable)
ov7251->current_mode->height);
goto err_power_down;
}
+ ret = ov7251_set_register_array(ov7251, ov7251_strobe_regs,
+ ARRAY_SIZE(ov7251_strobe_regs));
+ if (ret < 0) {
+ dev_err(ov7251->dev, "could not set strobe defaults\n");
+ goto err_power_down;
+ }
ret = __v4l2_ctrl_handler_setup(&ov7251->ctrls);
if (ret < 0) {
dev_err(ov7251->dev, "could not sync v4l2 controls\n");
--
2.53.0
next prev parent reply other threads:[~2026-10-26 11:10 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-26 11:10 [PATCH 0/7] media: i2c: ov7251: fixes and infrared strobe for Surface Book 2 Antoine Pichot
2026-10-26 11:10 ` [PATCH 1/7] media: i2c: ov7251: Fix link frequency index Antoine Pichot
2026-10-26 11:10 ` [PATCH 2/7] media: i2c: ov7251: Reset vblank when the frame interval changes Antoine Pichot
2026-10-26 11:10 ` [PATCH 3/7] media: i2c: ov7251: Add control event support Antoine Pichot
2026-10-26 11:34 ` Sakari Ailus
2026-10-26 13:03 ` Antoine Pichot
2026-10-26 11:10 ` [PATCH 4/7] media: i2c: ov7251: Add orientation and rotation controls Antoine Pichot
2026-10-26 11:10 ` Antoine Pichot [this message]
2026-10-26 11:10 ` [PATCH 6/7] media: i2c: ov7251: Add strobe output enable control Antoine Pichot
2026-10-26 15:14 ` Andy Shevchenko
2026-10-26 11:10 ` [PATCH 7/7] media: ipu-bridge: Add a 90 degree rotation quirk for Surface Book 2 Antoine Pichot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261026111032.88355-6-antoine.pichot@gmail.com \
--to=antoine.pichot@gmail.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=dan.scally@ideasonboard.com \
--cc=djrscally@gmail.com \
--cc=hansg@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=sakari.ailus@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®