From: Florian Fainelli <f.fainelli@gmail.com>
To: netdev@vger.kernel.org
Cc: Florian Fainelli <f.fainelli@gmail.com>,
Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@kernel.org>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Heiner Kallweit <hkallweit1@gmail.com>,
Russell King <linux@armlinux.org.uk>,
Jijie Shao <shaojijie@huawei.com>,
Simon Horman <horms@kernel.org>,
Runyu Xiao <runyu.xiao@seu.edu.cn>,
David Yang <mmyangfl@gmail.com>,
Herbert Valerio Riedel <hvr@gnu.org>,
Jeff Garzik <jeff@garzik.org>,
Danny Kukawka <danny.kukawka@bisect.de>,
Mugunthan V N <mugunthanvnm@ti.com>,
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>,
linux-kernel@vger.kernel.org (open list),
Manuel Lauss <manuel.lauss@gmail.com>
Subject: [PATCH net 10/11] net: au1000: keep the MAC stopped until the PHY link is ready
Date: Tue, 27 Oct 2026 15:31:39 -0700 [thread overview]
Message-ID: <20261027223140.3774570-11-f.fainelli@gmail.com> (raw)
In-Reply-To: <20261027223140.3774570-1-f.fainelli@gmail.com>
phy_stop() powers down the PHY when the interface is closed. The driver
leaves MAC receive/transmit enabled on link-down and enables them again
during initialization before resuming the PHY. The MTX-1 can hang when
the MAC runs while its MII clocks are absent or still recovering.
Start the PHY before initializing the MAC, but leave receive/transmit
stopped while the PHY reports no link. The duplex update enables them
when the link comes up. Stop the MAC in the link-down callback before
phylib suspends the PHY, and stop the PHY if MAC initialization fails.
Fixes: be9dad1f9f26 ("net: phy: suspend phydev when going to HALTED")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/amd/au1000_eth.c | 17 ++++++++++++-----
1 file changed, 12 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ethernet/amd/au1000_eth.c b/drivers/net/ethernet/amd/au1000_eth.c
index 8c2dbf72652e..c616ce616541 100644
--- a/drivers/net/ethernet/amd/au1000_eth.c
+++ b/drivers/net/ethernet/amd/au1000_eth.c
@@ -458,7 +458,8 @@ au1000_adjust_link(struct net_device *dev)
/* link state changed */
if (!phydev->link) {
- /* link went down */
+ /* Stop the MAC before the PHY can remove its clocks. */
+ au1000_hard_stop(dev);
aup->old_speed = 0;
aup->old_duplex = -1;
}
@@ -727,7 +728,7 @@ static int au1000_init(struct net_device *dev)
wmb(); /* drain writebuffer */
- control = MAC_RX_ENABLE | MAC_TX_ENABLE;
+ control = 0;
#ifndef CONFIG_CPU_LITTLE_ENDIAN
control |= MAC_BIG_ENDIAN;
#endif
@@ -740,6 +741,10 @@ static int au1000_init(struct net_device *dev)
control |= MAC_FULL_DUPLEX;
}
+ /* The PHY may still be restoring its MII clocks after resume. */
+ if (!dev->phydev || dev->phydev->link)
+ control |= MAC_RX_ENABLE | MAC_TX_ENABLE;
+
writel(control, &aup->mac->control);
writel(0x8100, &aup->mac->vlan1_tag); /* activate vlan support */
wmb(); /* drain writebuffer */
@@ -928,16 +933,18 @@ static int au1000_open(struct net_device *dev)
return retval;
}
+ if (dev->phydev)
+ phy_start(dev->phydev);
+
retval = au1000_init(dev);
if (retval) {
netdev_err(dev, "error in au1000_init\n");
+ if (dev->phydev)
+ phy_stop(dev->phydev);
free_irq(dev->irq, dev);
return retval;
}
- if (dev->phydev)
- phy_start(dev->phydev);
-
netif_start_queue(dev);
netif_dbg(aup, drv, dev, "open: Initialization done.\n");
--
2.53.0
next prev parent reply other threads:[~2026-10-27 22:32 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-27 22:31 [PATCH net 00/11] net: au1000: Bug fixes Florian Fainelli
2026-10-27 22:31 ` [PATCH net 01/11] net: au1000: recycle RX descriptors on allocation failure Florian Fainelli
2026-10-27 22:31 ` [PATCH net 02/11] net: au1000: clear all-multicast mode when restoring hash filtering Florian Fainelli
2026-10-27 22:31 ` [PATCH net 03/11] net: au1000: disconnect the PHY before freeing the MDIO bus Florian Fainelli
2026-10-27 22:31 ` [PATCH net 04/11] net: au1000: report MDIO transaction timeouts Florian Fainelli
2026-10-27 22:31 ` [PATCH net 05/11] net: au1000: serialize TX completion with packet submission Florian Fainelli
2026-10-27 22:31 ` [PATCH net 06/11] net: au1000: assign a valid MAC address without platform data Florian Fainelli
2026-10-27 22:31 ` [PATCH net 07/11] net: au1000: fix buffer descriptor free list insertion Florian Fainelli
2026-10-27 22:31 ` [PATCH net 08/11] net: au1000: restore receive filtering after MAC initialization Florian Fainelli
2026-10-27 22:31 ` [PATCH net 09/11] net: au1000: restore RX buffer addresses when restarting the MAC Florian Fainelli
2026-10-27 22:31 ` Florian Fainelli [this message]
2026-10-27 22:31 ` [PATCH net 11/11] net: phy: smsc: wait for LAN83C183 power-down recovery Florian Fainelli
2026-10-27 23:21 ` [PATCH net 00/11] net: au1000: Bug fixes Jakub Kicinski
2026-10-28 0:12 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261027223140.3774570-11-f.fainelli@gmail.com \
--to=f.fainelli@gmail.com \
--cc=andrew+netdev@lunn.ch \
--cc=danny.kukawka@bisect.de \
--cc=davem@davemloft.net \
--cc=edumazet@kernel.org \
--cc=hkallweit1@gmail.com \
--cc=horms@kernel.org \
--cc=hvr@gnu.org \
--cc=jeff@garzik.org \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=manuel.lauss@gmail.com \
--cc=mmyangfl@gmail.com \
--cc=mugunthanvnm@ti.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=runyu.xiao@seu.edu.cn \
--cc=sebastian.hesselbarth@gmail.com \
--cc=shaojijie@huawei.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®