On Tue, Oct 13, 2026 at 03:28:41AM +0000, Jizhou Tong wrote:
> Describe the fixed-address HID-over-SPI touchpad on Surface Laptop 7
> 13.8-inch, with quad address/data transfers, an active-low reset and a 5
> V supply.
> 
> Signed-off-by: Jizhou Tong <fqwqf@fqwqf.xyz>

With the changes to the hid-over-spi series that this is based on, can
this device now go into hid-over-spi.yaml?

> ---
>  .../input/microsoft,romulus13-touchpad.yaml   | 86 +++++++++++++++++++
>  1 file changed, 86 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/input/microsoft,romulus13-touchpad.yaml
> 
> diff --git a/Documentation/devicetree/bindings/input/microsoft,romulus13-touchpad.yaml b/Documentation/devicetree/bindings/input/microsoft,romulus13-touchpad.yaml
> new file mode 100644
> index 0000000000000000000000000000000000000000..88e4664c56e7fb1c3f9f5949a3ded2f9d7070604
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/input/microsoft,romulus13-touchpad.yaml
> @@ -0,0 +1,86 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/input/microsoft,romulus13-touchpad.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Microsoft Surface Laptop 7 13.8-inch QSPI touchpad
> +
> +maintainers:
> +  - Jizhou Tong <fqwqf@fqwqf.xyz>
> +
> +description:
> +  The touchpad on the 13.8-inch Surface Laptop 7 uses the HID SPI v3
> +  protocol over a quad SPI connection. Its supply and board reset states
> +  must be controlled during initialization and recovery.
> +
> +allOf:
> +  - $ref: /schemas/spi/spi-peripheral-props.yaml#
> +
> +properties:
> +  compatible:
> +    const: microsoft,romulus13-touchpad
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  vdd-supply:
> +    description: Touchpad 5 V supply.
> +
> +  spi-max-frequency:
> +    maximum: 20000000
> +
> +  spi-rx-bus-width:
> +    items:
> +      - const: 4
> +
> +  spi-tx-bus-width:
> +    items:
> +      - const: 4
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description: Active-low touchpad reset.
> +

> +  pinctrl-0: true
> +
> +  pinctrl-names:
> +    items:
> +      - const: default

Are these even something that needs to be added? I am pretty sure pinctrl
stuff is allowed in all nodes without being cited explicitly.

Looks okay to me other than these two things.

pw-bot: changes-requested

Thanks,
Conor.

> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - vdd-supply
> +  - spi-rx-bus-width
> +  - spi-tx-bus-width
> +  - reset-gpios
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    spi {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        touchpad@0 {
> +            compatible = "microsoft,romulus13-touchpad";
> +            reg = <0>;
> +            spi-max-frequency = <20000000>;
> +            spi-rx-bus-width = <4>;
> +            spi-tx-bus-width = <4>;
> +            interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
> +            vdd-supply = <&vreg_ts_5p0>;
> +            reset-gpios = <&tlmm 120 GPIO_ACTIVE_LOW>;
> +            pinctrl-0 = <&touchpad_reset>;
> +            pinctrl-names = "default";
> +        };
> +    };
> -- 
> 2.53.0
>