From: anand.tiwari@oss.qualcomm.com
To: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Abel Vesa <abelvesa@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Florian Fainelli <florian.fainelli@broadcom.com>,
Broadcom internal kernel review list
<bcm-kernel-feedback-list@broadcom.com>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-rpi-kernel@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
Anand Tiwari <anand.tiwari@oss.qualcomm.com>,
Mohit Dsor <mohit.dsor@oss.qualcomm.com>,
Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>,
Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Subject: [PATCH v2 0/6] arm64: dts: qcom: talos-lyra-evk: Add display overlays for EVK board
Date: Fri, 30 Oct 2026 15:10:04 +0530 [thread overview]
Message-ID: <20261030-lyra-display-upstream-post-v2-0-906302159392@oss.qualcomm.com> (raw)
Talos Lyra EVK SoC card are mounted on the Lyra carrier card. The
DSI0 interface from SoC card is routed to either the 22-pin DSI
connector on carrier card named as JDISP1 DSI0 or to the DSI0_B2B
connector, through a MUX which can be selected by a hardware DIP
switch. There are multiple daughter cards designed that can be
connected to this B2B connector.
The below B2B display interfaces are enabled by default in base DTB:
- DSI-to-HDMI using the LT9611UXD daughter card
Below overlay DTs are added for additional display configurations:
- talos-lyra-evk-dlc0697: DLC0697 DSI panel for Lyra with DLC
daughter card
- talos-lyra-evk-raspberrypi-dsi-7inch: Raspberry Pi 7-inch DSI
panel with touch via the 22-pin DSI connector for Lyra
- talos-lyra-evk-waveshare-dsi-8inch: Waveshare 8-inch DSI panel
with touch via the 22-pin DSI connector for Lyra
- talos-lyra-evk-lvds-auo,g133han01: AUO G133HAN01 LVDS panel for
Lyra with LVDS daughter card
These overlays are applied on top of the corresponding base board
DTBs.
Link: https://lore.kernel.org/r/20261012-talos-lyra-evk-v2-v2-0-dcc9316ebb59@oss.qualcomm.com
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
Changes in v2:
- Fold in the hdmi_connector port remote-endpoint indentation fix.
- Drop the per-patch Depends-on trailer on the LT9611UXD HDMI bridge
patch; the dt-bindings dependency is now declared as a series
prerequisite (see base-commit/prerequisite info below).
- Drop default-on from the DLC0697 backlight node.
- Add the ilitek,ili9881c fallback compatible to the RPi 7-inch
panel overlay to fix a dtbs_check "too short" binding failure.
- Reword the PWM_CLK defconfig commit message to name Qualcomm as
the SoC vendor.
- Remove a stray blank line and non-ASCII characters from the AUO
LVDS panel overlay.
- Link to v1: https://patch.msgid.link/20261021-lyra-display-upstream-post-v1-0-585caa39cd7c@oss.qualcomm.com
To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
To: Abel Vesa <abelvesa@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Florian Fainelli <florian.fainelli@broadcom.com>
To: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
---
Anand Tiwari (2):
arm64: defconfig: Enable PWM_CLK for backlight PWM support
arm64: dts: qcom: talos-lyra-evk: Add AUO G133HAN01 LVDS panel overlay
Mohit Dsor (1):
arm64: dts: qcom: talos-lyra-evk: Add LT9611UXD HDMI bridge support
Shashank Maurya (3):
arm64: dts: qcom: talos-lyra-evk: Add DLC DLC0697 panel overlay
arm64: dts: qcom: talos-lyra-evk: Add RPi 7-inch DSI panel overlay
arm64: dts: qcom: talos-lyra-evk: Add Waveshare 8-inch DSI panel overlay
arch/arm64/boot/dts/qcom/Makefile | 18 +++
.../boot/dts/qcom/talos-lyra-evk-dlc0697.dtso | 77 ++++++++++++
.../qcom/talos-lyra-evk-lvds-auo,g133han01.dtso | 133 +++++++++++++++++++++
.../qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso | 88 ++++++++++++++
.../qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso | 75 ++++++++++++
arch/arm64/boot/dts/qcom/talos-lyra-evk.dts | 106 ++++++++++++++++
arch/arm64/configs/defconfig | 1 +
7 files changed, 498 insertions(+)
---
base-commit: 4eb2586bd40db27d77cc5b724ca9386ed0c71d53
change-id: 20261019-lyra-display-upstream-post-24656268a902
prerequisite-message-id: <20261027-talos-lyra-evk-v2-v3-0-658fd5a7ec99@oss.qualcomm.com>
prerequisite-patch-id: 0dfae1e9d0c620866489eecacb4b7201b9333621
prerequisite-patch-id: 94923ba8f57911649364a7e0e5494c7cfd478367
prerequisite-patch-id: 660755293839baa7364b4baf3a2dd6b4018de48a
prerequisite-message-id: <20261021-lt9611c-v7-v18-0-4978b94896f1@oss.qualcomm.com>
prerequisite-patch-id: 49f1e01bb5594ce9c4301ce4b16715834ece7f41
prerequisite-patch-id: 21cfbbfd71515961501a768edad476740336c13c
Best regards,
--
Anand Tiwari <anand.tiwari@oss.qualcomm.com>
next reply other threads:[~2026-10-30 9:40 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-30 9:40 anand.tiwari [this message]
2026-10-30 9:40 ` [PATCH v2 1/6] arm64: dts: qcom: talos-lyra-evk: Add LT9611UXD HDMI bridge support anand.tiwari
2026-10-30 9:40 ` [PATCH v2 2/6] arm64: dts: qcom: talos-lyra-evk: Add DLC DLC0697 panel overlay anand.tiwari
2026-10-30 9:40 ` [PATCH v2 3/6] arm64: dts: qcom: talos-lyra-evk: Add RPi 7-inch DSI " anand.tiwari
2026-10-30 9:40 ` [PATCH v2 4/6] arm64: dts: qcom: talos-lyra-evk: Add Waveshare 8-inch " anand.tiwari
2026-10-30 9:40 ` [PATCH v2 5/6] arm64: defconfig: Enable PWM_CLK for backlight PWM support Anand Tiwari
2026-11-01 20:29 ` Krzysztof Kozlowski
2026-10-30 9:40 ` [PATCH v2 6/6] arm64: dts: qcom: talos-lyra-evk: Add AUO G133HAN01 LVDS panel overlay Anand Tiwari
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261030-lyra-display-upstream-post-v2-0-906302159392@oss.qualcomm.com \
--to=anand.tiwari@oss.qualcomm.com \
--cc=abelvesa@kernel.org \
--cc=andersson@kernel.org \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=florian.fainelli@broadcom.com \
--cc=konrad.dybcio@oss.qualcomm.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=mohit.dsor@oss.qualcomm.com \
--cc=robh@kernel.org \
--cc=shashank.maurya@oss.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®