On Sat, Oct 31, 2026 at 02:55:31PM +0800, Qianhui Xu wrote:
> The WL2868C is an I2C-controlled camera power management IC from Will
> Semiconductor. It provides seven programmable LDOs: LDO1 and LDO2 are
> fed from a shared VIN12 input and cover 0.496 V to 1.512 V, LDO3 and
> LDO4 share VIN34, and LDO5 to LDO7 each have their own input, covering
> 1.504 V to 3.544 V. All outputs are programmable in 8 mV steps and are
> gated by per-output enable bits with a chip-wide SYS_EN master. The
> chip also exposes an optional active-low RST_N input.
> 

> Its user on the Lenovo Legion Tab (TB322FC, SM8750) is the camera
> subsystem: the rear samsung,s5kjns sensor takes DVDD from LDO1, AVDD
> from LDO4 and DOVDD from LDO7, and the rear giantec,gt9764 voice coil
> motor takes VDD from LDO5 and VDDIO from LDO7. The front sensor is
> powered from LDO2, LDO3 and LDO7, but its binding is still pending, so
> its supply wiring follows with that series. The board DTS patch of this
> series describes the supply wiring that is documented; LDO6 is the only
> output with no user on this board.

None of this is relevant to the wl2868c binding.

> 
> Signed-off-by: Qianhui Xu <xiaqinghuan@mail.ustc.edu.cn>
> ---
>  .../devicetree/bindings/arm/qcom.yaml         |  1 +
>  .../bindings/regulator/willsemi,wl2868c.yaml  | 79 +++++++++++++++++++
>  2 files changed, 80 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/regulator/willsemi,wl2868c.yaml
> 
> diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
> index ff8a35df78..41d5e65c4e 100644
> --- a/Documentation/devicetree/bindings/arm/qcom.yaml
> +++ b/Documentation/devicetree/bindings/arm/qcom.yaml
> @@ -1168,6 +1168,7 @@ properties:
>  
>        - items:
>            - enum:
> +              - lenovo,elden

This has nothing to do with the willsemi device and should not be in
this patch.

>                - qcom,sm8750-mtp
>                - qcom,sm8750-qrd
>            - const: qcom,sm8750
> diff --git a/Documentation/devicetree/bindings/regulator/willsemi,wl2868c.yaml b/Documentation/devicetree/bindings/regulator/willsemi,wl2868c.yaml
> new file mode 100644
> index 0000000000..96541870cd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/regulator/willsemi,wl2868c.yaml
> @@ -0,0 +1,79 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/regulator/willsemi,wl2868c.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Will Semiconductor WL2868C camera power management IC
> +
> +maintainers:
> +  - Qianhui Xu <xiaqinghuan@mail.ustc.edu.cn>
> +
> +description:
> +  The WL2868C is a camera power management IC with seven programmable LDOs.
> +  LDO1 and LDO2 share the VIN12 input and cover 0.496 V to 1.512 V; LDO3 and
> +  LDO4 share VIN34, and LDO5 to LDO7 have one input each, covering 1.504 V to
> +  3.544 V. All outputs are programmable in 8 mV steps.
> +
> +properties:
> +  compatible:
> +    const: willsemi,wl2868c
> +
> +  reg:
> +    maxItems: 1
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description: Active-low RST_N input.
> +
> +  vin12-supply:
> +    description: Input supply for LDO1 and LDO2.
> +
> +  vin34-supply:
> +    description: Input supply for LDO3 and LDO4.
> +
> +  vin5-supply:
> +    description: Input supply for LDO5.
> +
> +  vin6-supply:
> +    description: Input supply for LDO6.
> +
> +  vin7-supply:
> +    description: Input supply for LDO7.
> +
> +  regulators:
> +    type: object
> +    additionalProperties: false
> +
> +    patternProperties:
> +      "^ldo[1-7]$":
> +        type: object
> +        $ref: regulator.yaml#
> +        unevaluatedProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - regulators

I assume you didn't make the input supplies mandatory because if their
output is not used, they're not actually needed?

That said, you're missing the vsys supply which I suspect may actually
be mandatory? At the very least, one of vin7 and vsys is mandatory,
because the higher of the two powers the internal control logic...

pw-bot: changes-requested

Thanks,
Conor.

> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        pmic@2f {
> +            compatible = "willsemi,wl2868c";
> +            reg = <0x2f>;
> +
> +            regulators {
> +                ldo1 {
> +                    regulator-max-microvolt = <1128000>;
> +                    regulator-min-microvolt = <1128000>;
> +                };
> +            };
> +        };
> +    };
> +...
> -- 
> 2.53.0
>