From: Linghui Wu <linghui.wu@oss.qualcomm.com>
To: Bjorn Helgaas <bhelgaas@google.com>,
Manivannan Sadhasivam <mani@kernel.org>,
Bjorn Andersson <andersson@kernel.org>
Cc: "Lorenzo Pieralisi" <lpieralisi@kernel.org>,
"Krzysztof Wilczyński" <kwilczynski@kernel.org>,
"Konrad Dybcio" <konradybcio@kernel.org>,
"Abel Vesa" <abelvesa@kernel.org>,
"Rob Herring" <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Dmitry Baryshkov" <dmitry.baryshkov@oss.qualcomm.com>,
"Sushrut Shree Trivedi" <sushrut.trivedi@oss.qualcomm.com>,
"Miaoqing Pan" <miaoqing.pan@oss.qualcomm.com>,
"Hangtian Zhu" <hangtian.zhu@oss.qualcomm.com>,
"Shuai Zhang" <shuai.zhang@oss.qualcomm.com>,
"Cheng Jiang" <cheng.jiang@oss.qualcomm.com>,
"Wei Deng" <wei.deng@oss.qualcomm.com>,
linux-pci@vger.kernel.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
"Linghui Wu" <linghui.wu@oss.qualcomm.com>
Subject: [PATCH v5 4/4] arm64: dts: qcom: shikra-iqs: add M.2 Wi-Fi and Bluetooth overlay
Date: Thu, 12 Nov 2026 16:33:55 +0800 [thread overview]
Message-ID: <20261112083355.3884737-5-linghui.wu@oss.qualcomm.com> (raw)
In-Reply-To: <20261112083355.3884737-1-linghui.wu@oss.qualcomm.com>
Add an overlay for M.2 Key-E Wi-Fi and Bluetooth modules on the
Qualcomm Shikra IQS EVK.
The Shikra product design supports either the onboard Apache WCN3988
path or the M.2 HSP Cologne path at a time. The overlay describes the
board after hardware rework selects the M.2 path. Disable the inherited
onboard Wi-Fi and Bluetooth nodes when this overlay is selected.
Describe the PCIe and UART connections through the M.2 connector, the
3.3 V supply, the W_DISABLE signals and the PCIe reset signal.
The series has been validated on Shikra hardware.
Link: https://lore.kernel.org/r/20261102045815.2938940-1-linghui.wu@oss.qualcomm.com
Co-developed-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Linghui Wu <linghui.wu@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso | 122 ++++++++++++++++++
2 files changed, 124 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 8329c06b60a3..037dbe8a39ce 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -410,10 +410,12 @@ dtb-$(CONFIG_ARCH_QCOM) += shikra-iqs-evk.dtb
shikra-cqm-evk-imx577-camera-dtbs := shikra-cqm-evk.dtb shikra-cqm-cqs-evk-imx577-camera.dtbo
shikra-cqs-evk-imx577-camera-dtbs := shikra-cqs-evk.dtb shikra-cqm-cqs-evk-imx577-camera.dtbo
shikra-iqs-evk-imx577-camera-dtbs := shikra-iqs-evk.dtb shikra-iqs-evk-imx577-camera.dtbo
+shikra-iqs-evk-m2-wifi-bt-dtbs := shikra-iqs-evk.dtb shikra-iqs-evk-m2-wifi-bt.dtbo
dtb-$(CONFIG_ARCH_QCOM) += shikra-cqm-evk-imx577-camera.dtb
dtb-$(CONFIG_ARCH_QCOM) += shikra-cqs-evk-imx577-camera.dtb
dtb-$(CONFIG_ARCH_QCOM) += shikra-iqs-evk-imx577-camera.dtb
+dtb-$(CONFIG_ARCH_QCOM) += shikra-iqs-evk-m2-wifi-bt.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm4250-oneplus-billie2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm4450-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm6115-fxtec-pro1x.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
new file mode 100644
index 000000000000..ef0f197a53f8
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ m2_keye_3p3: regulator-m2-keye-3p3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_3P3_KEYE";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&expander3 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ wifi-bt-connector {
+ compatible = "pcie-m2-e-connector";
+
+ vpcie3v3-supply = <&m2_keye_3p3>;
+ w-disable1-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+ w-disable2-gpios = <&tlmm 60 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ m2_e_pcie_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&pcie_port0_ep>;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ m2_e_uart_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&uart8_ep>;
+ };
+ };
+ };
+ };
+};
+
+&{/wcn3988-pmu} {
+ status = "disabled";
+};
+
+&pcie {
+ iommu-map = <0x0 &apps_smmu 0x0800 0x0 0x1>,
+ <0x100 &apps_smmu 0x0801 0x0 0x1>;
+ pinctrl-0 = <&pcie_default_state>;
+ pinctrl-names = "default";
+ vddpe-3v3-supply = <&m2_keye_3p3>;
+ wake-gpios = <&tlmm 119 GPIO_ACTIVE_LOW>;
+
+ status = "okay";
+};
+
+&pcie_phy {
+ vdda-phy-supply = <&pm8150_l12>;
+ vdda-pll-supply = <&pm8150_l9>;
+
+ status = "okay";
+};
+
+&pcie_port0 {
+ compatible = "pciclass,0604";
+ reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
+
+ port {
+ pcie_port0_ep: endpoint {
+ remote-endpoint = <&m2_e_pcie_ep>;
+ };
+ };
+};
+
+&uart8 {
+ bluetooth {
+ status = "disabled";
+ };
+
+ port {
+ uart8_ep: endpoint {
+ remote-endpoint = <&m2_e_uart_ep>;
+ };
+ };
+};
+
+&tlmm {
+ pcie_default_state: pcie-default-state {
+ clkreq-pins {
+ pins = "gpio117";
+ function = "pcie0_clk_req_n";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake-pins {
+ pins = "gpio119";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+};
+
+&wifi {
+ status = "disabled";
+};
--
2.43.0
prev parent reply other threads:[~2026-11-12 8:34 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-12 8:33 [PATCH v5 0/4] PCI: qcom: add Shikra PCIe and M.2 Wi-Fi/BT support Linghui Wu
2026-11-12 8:33 ` [PATCH v5 1/4] dt-bindings: PCI: qcom: document the Shikra PCIe controller Linghui Wu
2026-11-12 8:33 ` [PATCH v5 2/4] PCI: qcom: add support for " Linghui Wu
2026-11-12 8:33 ` [PATCH v5 3/4] arm64: dts: qcom: shikra: add PCIe PHY and controller nodes Linghui Wu
2026-11-12 8:33 ` Linghui Wu [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261112083355.3884737-5-linghui.wu@oss.qualcomm.com \
--to=linghui.wu@oss.qualcomm.com \
--cc=abelvesa@kernel.org \
--cc=andersson@kernel.org \
--cc=bhelgaas@google.com \
--cc=cheng.jiang@oss.qualcomm.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@oss.qualcomm.com \
--cc=hangtian.zhu@oss.qualcomm.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=kwilczynski@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=lpieralisi@kernel.org \
--cc=mani@kernel.org \
--cc=miaoqing.pan@oss.qualcomm.com \
--cc=robh@kernel.org \
--cc=shuai.zhang@oss.qualcomm.com \
--cc=sushrut.trivedi@oss.qualcomm.com \
--cc=wei.deng@oss.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®