[PATCH v10 07/10] Documentation: PCI: endpoint: Document vNTB DMA export

[Koichiro Den <den@valinux.co.jp>]

Document the dma_bar attribute and the requirements for exporting
endpoint DMA channels. Also document how the selected BAR may be shared
with an MW.

Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Koichiro Den <den@valinux.co.jp>
---
Changes in v10:
  - Remove the IRQ-allocation fallback description now that DMA uses slot 1.
    R-b tag is kept. Only patch 9 should need another review.
  - Link to v9: https://lore.kernel.org/r/20261110082459.1798763-8-den@valinux.co.jp/

 Documentation/PCI/endpoint/pci-vntb-howto.rst | 33 +++++++++++++++++--
 1 file changed, 30 insertions(+), 3 deletions(-)

diff --git a/Documentation/PCI/endpoint/pci-vntb-howto.rst b/Documentation/PCI/endpoint/pci-vntb-howto.rst
index 3679f5c30254..f53cd0fe91b0 100644
--- a/Documentation/PCI/endpoint/pci-vntb-howto.rst
+++ b/Documentation/PCI/endpoint/pci-vntb-howto.rst
@@ -90,9 +90,9 @@ of the function device and is populated with the following NTB specific
 attributes that can be configured by the user::
 
 	# ls functions/pci_epf_vntb/func1/pci_epf_vntb.0/
-	ctrl_bar  db_count  mw1_bar  mw2_bar  mw3_bar  mw4_bar	spad_count
-	db_bar	  mw1	    mw2      mw3      mw4      num_mws	vbus_number
-	vntb_vid  vntb_pid
+	ctrl_bar  dma_bar  mw2      mw3_bar  num_mws     vntb_pid
+	db_bar    mw1      mw2_bar  mw4      spad_count  vntb_vid
+	db_count  mw1_bar  mw3      mw4_bar  vbus_number
 
 A sample configuration for NTB function is given below::
 
@@ -105,6 +105,33 @@ By default, each construct is assigned a BAR, as needed and in order.
 Should a specific BAR setup be required by the platform, BAR may be assigned
 to each construct using the related ``XYZ_bar`` entry.
 
+To export DMA channels, set ``dma_bar`` before binding the function.
+For example::
+
+	# echo 5 > functions/pci_epf_vntb/func1/pci_epf_vntb.0/dma_bar
+
+This currently supports the unrolled DesignWare eDMA layout. The EPC must
+support subrange and dynamic inbound mappings.
+
+``dma_bar`` cannot select the control or doorbell BAR.
+Any rounded-up BAR tail is scratch-backed.
+
+Leaving ``dma_bar`` unassigned disables DMA export.
+With a separate DMA BAR, an older ``ntb_hw_epf`` peer can ignore the extension
+and continue without DMA. A peer that understands the extension also continues
+without DMA if the advertised type is unavailable.
+
+If no spare BAR is available, ``dma_bar`` can select the BAR of one MW instead.
+DMA resources then follow that MW. In this configuration:
+
+* The configured MW size must be a power of two and meet the EPC's alignment
+  requirement. Without the fallback described below, the MW translation must
+  cover that full size. Smaller requests are rejected, including those caused
+  by the host's ``max_mw_size`` setting for ``ntb_transport``.
+* Older peers treat the whole BAR as an MW. The function detects this at
+  link-up and then exposes the whole BAR as the MW, so NTB still works
+  without DMA.
+
 A sample configuration for virtual NTB driver for virtual PCI bus::
 
 	# echo 0x1957 > functions/pci_epf_vntb/func1/pci_epf_vntb.0/vntb_vid
-- 
2.54.0