From: Jun Yan <jerrysteve1101@gmail.com>
To: jernej.skrabec@gmail.com
Cc: conor+dt@kernel.org, devicetree@vger.kernel.org,
james.hilliard1@gmail.com, krzk+dt@kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-sunxi@lists.linux.dev,
robh@kernel.org, samuel@sholland.org, wens@kernel.org
Subject: Re: [PATCH 0/2] arm64: dts: allwinner: h6: Enable Ethernet on Tanix TX6
Date: Mon, 16 Nov 2026 22:25:03 +0800 [thread overview]
Message-ID: <20261116142503.671907-1-jerrysteve1101@gmail.com> (raw)
In-Reply-To: <20261115171148.37784-1-jernej.skrabec@gmail.com>
Hi Jernej,
> The AC200 MFD and Ethernet PHY drivers and their bindings were merged
> in v7.4-rc1. This series adds the device tree parts needed to use them
> on H6, starting with the Tanix TX6 and TX6 mini TV boxes, whose only
> Ethernet port goes through the PHY in the AC200 co-packaged with the
> H6.
>
> Patch 1 describes the AC200 in the H6 dtsi: the I2C3 controller with
> the AC200 on it, a pwm-clock that provides its 24 MHz reference clock
> from PWM1, the RMII pins and the EPHY calibration value in the SID.
> Everything stays disabled.
>
> Patch 2 enables Ethernet on the Tanix boards.
>
> Tested on a Tanix TX6: 100 Mbit/s full duplex, about 11 MB/s in each
> direction, and the link comes up both after cold boots with no
> Ethernet initialisation in U-Boot and after U-Boot has used it. The
> TX6 mini shares the same dtsi and was not tested separately.
>
> The arm64 defconfig does not enable CONFIG_MFD_AC200 and
> CONFIG_XPOWERS_ACX00_PHY yet; I can send a separate patch for that.
>
> Best regards,
> Jernej
>
> Jernej Skrabec (2):
> arm64: dts: allwinner: sun50i-h6: Add AC200 companion chip
> arm64: dts: allwinner: tanix: Enable Ethernet
>
> .../boot/dts/allwinner/sun50i-h6-tanix.dtsi | 40 ++++++++++++++
> arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 53 +++++++++++++++++++
> 2 files changed, 93 insertions(+)
>
> --
> 2.43.0
Same AC200 setup on TaiqiCat (TQC) A01; I'll send the board enablement
separately once the H6 dtsi changes are merged.
Thanks,
Jun
prev parent reply other threads:[~2026-11-16 14:25 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-15 17:11 Jernej Skrabec
2026-11-15 17:11 ` [PATCH 1/2] arm64: dts: allwinner: sun50i-h6: Add AC200 companion chip Jernej Skrabec
2026-11-16 14:23 ` Jun Yan
2026-11-15 17:11 ` [PATCH 2/2] arm64: dts: allwinner: tanix: Enable Ethernet Jernej Skrabec
2026-11-16 14:25 ` Jun Yan [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261116142503.671907-1-jerrysteve1101@gmail.com \
--to=jerrysteve1101@gmail.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=james.hilliard1@gmail.com \
--cc=jernej.skrabec@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=robh@kernel.org \
--cc=samuel@sholland.org \
--cc=wens@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®