From: "Alexandra Østermark via B4 Relay" <devnull+alex.cramt.gmail.com@kernel.org>
To: Dinh Nguyen <dinguyen@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
"Mahesh Rao" <mahesh.rao@altera.com>,
"Mohamad Asyraaf Azhar" <mohamad.asyraaf.azhar@altera.com>,
"Alexandra Østermark" <alex.cramt@gmail.com>
Subject: [PATCH 3/3] arm64: dts: socfpga: agilex5: add support for Terasic DE25-Nano
Date: Wed, 18 Nov 2026 20:07:15 +0100 [thread overview]
Message-ID: <20261118-de25-nano-v1-3-473d16131f7a@gmail.com> (raw)
In-Reply-To: <20261118-de25-nano-v1-0-473d16131f7a@gmail.com>
From: Alexandra Østermark <alex.cramt@gmail.com>
The DE25-Nano is an Agilex 5 SoC FPGA board with gigabit Ethernet, a
microSD slot wired for 3.3 V only, USB and one HPS LED.
Based on Terasic's and Altera's vendor device trees for the board, which
describe the SD slot on an SDHCI node that upstream doesn't have; this
uses the upstream SD6HC sdmmc node instead.
Boot from microSD, gigabit Ethernet, USB, the LED and the watchdog were
tested on the board. The QSPI flash, the I2C buses and the SDM hardware
monitor are left out until they have been tested.
Signed-off-by: Alexandra Østermark <alex.cramt@gmail.com>
---
arch/arm64/boot/dts/altera/Makefile | 1 +
.../boot/dts/altera/socfpga_agilex5_de25_nano.dts | 91 ++++++++++++++++++++++
2 files changed, 92 insertions(+)
diff --git a/arch/arm64/boot/dts/altera/Makefile b/arch/arm64/boot/dts/altera/Makefile
index d38fe88a1..29170f793 100644
--- a/arch/arm64/boot/dts/altera/Makefile
+++ b/arch/arm64/boot/dts/altera/Makefile
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += socfpga_agilex_n6000.dtb \
socfpga_agilex_socdk_multiqspi.dtb \
socfpga_agilex_socdk_nand.dtb \
socfpga_agilex3_socdk.dtb \
+ socfpga_agilex5_de25_nano.dtb \
socfpga_agilex5_socdk.dtb \
socfpga_agilex5_socdk_013b.dtb \
socfpga_agilex5_socdk_modular.dtb \
diff --git a/arch/arm64/boot/dts/altera/socfpga_agilex5_de25_nano.dts b/arch/arm64/boot/dts/altera/socfpga_agilex5_de25_nano.dts
new file mode 100644
index 000000000..1617600e1
--- /dev/null
+++ b/arch/arm64/boot/dts/altera/socfpga_agilex5_de25_nano.dts
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2023, Intel Corporation
+ * Copyright (C) 2026, Alexandra Østermark
+ */
+#include "socfpga_agilex5.dtsi"
+
+/ {
+ model = "Terasic DE25-Nano";
+ compatible = "terasic,de25-nano", "intel,socfpga-agilex5";
+
+ aliases {
+ serial0 = &uart1;
+ ethernet0 = &gmac0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "hps_led0";
+ gpios = <&portb 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the reg */
+ reg = <0x0 0x80000000 0x0 0x0>;
+ };
+};
+
+&gmac0 {
+ /* TX/RX delays are on the PCB */
+ phy-mode = "rgmii";
+ phy-handle = <&emac0_phy0>;
+ max-frame-size = <9000>;
+
+ status = "okay";
+
+ mdio0 {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ emac0_phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&osc1 {
+ clock-frequency = <25000000>;
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ no-1-8-v;
+ no-mmc;
+ no-sdio;
+
+ status = "okay";
+};
+
+&smmu {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ disable-over-current;
+
+ status = "okay";
+};
+
+&watchdog0 {
+ status = "okay";
+};
--
2.56.0
prev parent reply other threads:[~2026-11-18 19:07 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-18 19:07 [PATCH 0/3] " Alexandra Østermark via B4 Relay
2026-11-18 19:07 ` [PATCH 1/3] arm64: dts: socfpga: agilex5: add the service layer interrupt Alexandra Østermark via B4 Relay
2026-11-18 19:07 ` [PATCH 2/3] dt-bindings: arm: altera: add Terasic DE25-Nano Alexandra Østermark via B4 Relay
2026-11-18 19:07 ` Alexandra Østermark via B4 Relay [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261118-de25-nano-v1-3-473d16131f7a@gmail.com \
--to=devnull+alex.cramt.gmail.com@kernel.org \
--cc=alex.cramt@gmail.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dinguyen@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mahesh.rao@altera.com \
--cc=mohamad.asyraaf.azhar@altera.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®