From: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
To: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Abel Vesa <abelvesa@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Bartosz Golaszewski <brgl@kernel.org>,
Shawn Guo <shengchao.guo@oss.qualcomm.com>,
Andrew Halaney <ahalaney@redhat.com>,
Richard Cochran <richardcochran@gmail.com>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, netdev@vger.kernel.org,
Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Subject: [PATCH v3 2/2] arm64: dts: qcom: lemans-sa8255p: add ethernet nodes
Date: Wed, 18 Nov 2026 11:05:03 +0100 [thread overview]
Message-ID: <20261118-sa8255p-emac-dts-v3-2-e2c365d95a0b@oss.qualcomm.com> (raw)
In-Reply-To: <20261118-sa8255p-emac-dts-v3-0-e2c365d95a0b@oss.qualcomm.com>
Add the ethernet nodes along with their serdes PHY nodes for the gearvm
variant of the lemans ride board. Enable scmi7 and scmi8 to serve the
EMACs.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/lemans-gearvm.dtsi | 34 ++++
arch/arm64/boot/dts/qcom/lemans-sa8255p-ride.dts | 201 +++++++++++++++++++++++
2 files changed, 235 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/lemans-gearvm.dtsi b/arch/arm64/boot/dts/qcom/lemans-gearvm.dtsi
index 91c97a55f2787406b104650956b9a511a6a34c23..aaa8d96dfa61984afaeb13d7543140dd1724979d 100644
--- a/arch/arm64/boot/dts/qcom/lemans-gearvm.dtsi
+++ b/arch/arm64/boot/dts/qcom/lemans-gearvm.dtsi
@@ -58,6 +58,22 @@ &cpufreq_hw {
clock-names = "xo", "alternate";
};
+ðernet0 {
+ compatible = "qcom,sa8255p-ethqos";
+ phys = <&serdes0>;
+ phy-names = "serdes";
+ power-domains = <&scmi7_pd 0>, <&scmi7_pd 1>;
+ power-domain-names = "core", "mdio";
+};
+
+ðernet1 {
+ compatible = "qcom,sa8255p-ethqos";
+ phys = <&serdes1>;
+ phy-names = "serdes";
+ power-domains = <&scmi8_pd 0>, <&scmi8_pd 1>;
+ power-domain-names = "core", "mdio";
+};
+
&firmware {
scmi0: scmi-0 {
compatible = "qcom,scmi-smc";
@@ -2898,6 +2914,24 @@ &scm {
memory-region = <&tz_ffi_mem>;
};
+&soc {
+ serdes0: phy@8901000 {
+ compatible = "qcom,sa8255p-dwmac-sgmii-phy";
+ reg = <0x0 0x08901000 0x0 0xe10>;
+ #phy-cells = <0>;
+ power-domains = <&scmi7_dvfs 0>;
+ status = "disabled";
+ };
+
+ serdes1: phy@8902000 {
+ compatible = "qcom,sa8255p-dwmac-sgmii-phy";
+ reg = <0x0 0x08902000 0x0 0xe10>;
+ #phy-cells = <0>;
+ power-domains = <&scmi8_dvfs 0>;
+ status = "disabled";
+ };
+};
+
&spi0 {
compatible = "qcom,sa8255p-geni-spi";
power-domains = <&scmi10_pd 0>,
diff --git a/arch/arm64/boot/dts/qcom/lemans-sa8255p-ride.dts b/arch/arm64/boot/dts/qcom/lemans-sa8255p-ride.dts
index 6f19064997a4b50525fdf630307b843604368645..991626589cc34112df6e024d988bf87e6f520017 100644
--- a/arch/arm64/boot/dts/qcom/lemans-sa8255p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/lemans-sa8255p-ride.dts
@@ -14,6 +14,8 @@ / {
compatible = "qcom,sa8255p-ride", "qcom,sa8255p";
aliases {
+ ethernet0 = ðernet0;
+ ethernet1 = ðernet1;
serial0 = &uart10;
serial1 = &uart4;
};
@@ -101,6 +103,173 @@ trip1 {
};
};
+ðernet0 {
+ phy-handle = <&hsgmii_phy0>;
+ phy-mode = "2500base-x";
+
+ pinctrl-0 = <ðernet0_default>;
+ pinctrl-names = "default";
+
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+ snps,ps-speed = <2500>;
+
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hsgmii_phy0: phy@8 {
+ compatible = "ethernet-phy-id31c3.1c33";
+ reg = <0x8>;
+ device_type = "ethernet-phy";
+ resets = <&scmi7_rst 0>;
+ reset-names = "phy";
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
+ };
+
+ hsgmii_phy1: phy@0 {
+ compatible = "ethernet-phy-id31c3.1c33";
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ resets = <&scmi8_rst 0>;
+ reset-names = "phy";
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
+ };
+ };
+
+ mtl_rx_setup: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
+ðernet1 {
+ phy-mode = "2500base-x";
+ phy-handle = <&hsgmii_phy1>;
+
+ snps,mtl-rx-config = <&mtl_rx_setup1>;
+ snps,mtl-tx-config = <&mtl_tx_setup1>;
+ snps,ps-speed = <2500>;
+
+ status = "okay";
+
+ mtl_rx_setup1: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup1: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
&gpll0_board_clk {
clock-frequency = <300000000>;
};
@@ -145,6 +314,14 @@ &scmi6 {
status = "okay";
};
+&scmi7 {
+ status = "okay";
+};
+
+&scmi8 {
+ status = "okay";
+};
+
&scmi11 {
status = "okay";
};
@@ -162,6 +339,22 @@ &sleep_clk {
};
&tlmm {
+ ethernet0_default: ethernet0-default-state {
+ ethernet0_mdc: ethernet0-mdc-pins {
+ pins = "gpio8";
+ function = "emac0_mdc";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ethernet0_mdio: ethernet0-mdio-pins {
+ pins = "gpio9";
+ function = "emac0_mdio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
pcie0_ep_clkreq_default: pcie0-ep-clkreq-default-state {
pins = "gpio1";
function = "pcie0_clkreq";
@@ -205,6 +398,14 @@ pcie1_ep_wake_default: pcie1-ep-wake-default-state {
};
};
+&serdes0 {
+ status = "okay";
+};
+
+&serdes1 {
+ status = "okay";
+};
+
&uart4 {
status = "okay";
};
--
2.47.3
prev parent reply other threads:[~2026-11-18 10:05 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-18 10:05 [PATCH v3 0/2] arm64: dts: qcom: sa8255p: " Bartosz Golaszewski
2026-11-18 10:05 ` [PATCH v3 1/2] arm64: dts: qcom: lemans: fix iommus SID mask for " Bartosz Golaszewski
2026-11-18 10:05 ` Bartosz Golaszewski [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261118-sa8255p-emac-dts-v3-2-e2c365d95a0b@oss.qualcomm.com \
--to=bartosz.golaszewski@oss.qualcomm.com \
--cc=abelvesa@kernel.org \
--cc=ahalaney@redhat.com \
--cc=andersson@kernel.org \
--cc=brgl@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=richardcochran@gmail.com \
--cc=robh@kernel.org \
--cc=shengchao.guo@oss.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®