From: Simon Horman <horms@kernel.org>
To: han.junyang@zte.com.cn
Cc: Simon Horman <horms@kernel.org>,
andrew+netdev@lunn.ch, davem@davemloft.net, edumazet@google.com,
kuba@kernel.org, pabeni@redhat.com, linux-kernel@vger.kernel.org,
netdev@vger.kernel.org, ran.ming@zte.com.cn,
han.chengfei@zte.com.cn, zhang.yanze@zte.com.cn
Subject: Re: [PATCH net-next v6 1/3] dinghai: add firmware version check and RISC-V readiness polling
Date: Thu, 19 Nov 2026 12:05:37 +0000 [thread overview]
Message-ID: <20261119120536.1041197-2-horms@kernel.org> (raw)
In-Reply-To: <20261113135038394NowoSxTdiA32KKAPcTmCa@zte.com.cn>
This is an AI-generated review of your patch. The human sending this
email has considered the AI review valid, or at least plausible.
Full review at: https://sashiko.dev/#/patchset/20261113135038394NowoSxTdiA32KKAPcTmCa@zte.com.cn?part=1
---
dinghai: add firmware version check and RISC-V readiness polling
This commit polls the BAR 0 firmware compatibility block to verify the
driver/firmware version contract during PF probe and waits for the RISC-V
management core power-on flag when supported.
> diff --git a/drivers/net/ethernet/zte/dinghai/en_pf.c b/drivers/net/ethernet/zte/dinghai/en_pf.c
> index 86d4374088203..ddff9b0438fb3 100644
> --- a/drivers/net/ethernet/zte/dinghai/en_pf.c
> +++ b/drivers/net/ethernet/zte/dinghai/en_pf.c
[ ... ]
> @@ -369,6 +371,120 @@ int zxdh_pf_modern_cfg_init(struct zxdh_core_dev *zxdh_dev)
> return ret;
> }
>
> +/* The firmware fills the compatibility block field by field, so it is
> + * only ready to be read once every field we consume has lost its
> + * erased value.
> + */
> +static bool zxdh_pf_fw_compat_ready(struct zxdh_fw_compat __iomem *compat)
> +{
> + return ioread8(&compat->module_id) != 0xffU &&
> + ioread8(&compat->major) != 0xffU &&
> + ioread8(&compat->fw_minor) != 0xffU &&
> + ioread8(&compat->drv_minor) != 0xffU &&
> + ioread16(&compat->patch) != 0xffffU;
> +}
> +
> +/* Read the firmware version block and verify the driver/firmware
> + * version contract.
> + */
> +static int zxdh_pf_fw_compat_check(struct zxdh_core_dev *zxdh_dev)
> +{
> + struct zxdh_pf_dev *pf_dev = zxdh_dev->priv;
> + struct zxdh_fw_compat __iomem *compat;
> + struct zxdh_fw_compat *fw_compat;
> + bool ready;
> + int err;
> +
> + fw_compat = &pf_dev->fw_compat;
> + compat = pf_dev->pci_ioremap_addr[0] + ZXDH_FW_COMPAT_OFFSET;
> +
> + /* The firmware publishes the block within 10 s of boot; wait twice
> + * that to leave margin.
> + */
> + err = readx_poll_timeout(zxdh_pf_fw_compat_ready, compat, ready,
> + ready, USEC_PER_SEC,
> + ZXDH_FW_COMPAT_TIMEOUT_SEC * USEC_PER_SEC);
> + if (err)
> + dev_info(zxdh_dev->device,
> + "compat region not populated, assuming legacy firmware\n");
> +
> + /* Firmware predating the compatibility region keeps the erased
> + * pattern, which fails the module id check below and defers the
> + * decision to the readiness wait.
> + */
> + fw_compat->module_id = ioread8(&compat->module_id);
> + fw_compat->major = ioread8(&compat->major);
> + fw_compat->fw_minor = ioread8(&compat->fw_minor);
> + fw_compat->drv_minor = ioread8(&compat->drv_minor);
> + fw_compat->patch = ioread16(&compat->patch);
[Severity: Medium]
Does falling through on timeout here read and validate a partially populated
compatibility block?
Since the firmware populates compat field by field, readx_poll_timeout() can
time out after module_id is set to ZXDH_MODULE_ID while later fields still
hold 0xff or 0xffff. In that case the module_id check does not bail out, and
zxdh_pf_fw_compat_check() either fails probe with -EINVAL (if major or
drv_minor is still 0xff) or records fw_compat->patch as 0xffff, causing
zxdh_pf_wait_riscv_ready() to wait 40 seconds for riscv_power_on. Should the
if (err) branch set fw_compat->patch = 0 and return 0 directly?
next prev parent reply other threads:[~2026-11-19 12:06 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-13 5:47 [PATCH net-next v6 0/3] dinghai: firmware handshake, MSI-X pools and async event queues han.junyang
2026-11-13 5:50 ` [PATCH net-next v6 1/3] dinghai: add firmware version check and RISC-V readiness polling han.junyang
2026-11-19 12:05 ` Simon Horman [this message]
2026-11-13 5:52 ` [PATCH net-next v6 2/3] dinghai: add MSI-X interrupt pools han.junyang
2026-11-13 5:53 ` [PATCH net-next v6 3/3] dinghai: add async event queue for firmware notifications han.junyang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261119120536.1041197-2-horms@kernel.org \
--to=horms@kernel.org \
--cc=andrew+netdev@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=han.chengfei@zte.com.cn \
--cc=han.junyang@zte.com.cn \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=ran.ming@zte.com.cn \
--cc=zhang.yanze@zte.com.cn \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®