From: Hilda Wu <hildawu@realtek.com>
To: <marcel@holtmann.org>
Cc: <luiz.dentz@gmail.com>, <linux-bluetooth@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <alex_lu@realsil.com.cn>,
<jason_mao@realsil.com.cn>, <zoey_zhou@realsil.com.cn>,
<max.chou@realtek.com>, <kidman@realtek.com>,
<arunr@valvesoftware.com>
Subject: [PATCH v10 2/2] Bluetooth: btrtl: Add the support for RTL8922D
Date: Fri, 20 Nov 2026 16:26:36 +0800 [thread overview]
Message-ID: <20261120082636.3834168-3-hildawu@realtek.com> (raw)
In-Reply-To: <20261120082636.3834168-1-hildawu@realtek.com>
Add the support for RTL8922D BT controller on USB interface.
The necessary firmware will be submitted to linux-firmware project.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=a82d Rev= 0.00
S: Manufacturer=Realtek
S: Product=802.11be WLAN NIC
S: SerialNumber=00e04c000001
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 9 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=8d(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=0e(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Zoey Zhou <zoey_zhou@realsil.com.cn>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
---
drivers/bluetooth/btrtl.c | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/drivers/bluetooth/btrtl.c b/drivers/bluetooth/btrtl.c
index 49a13049fc50..6f46336bca5f 100644
--- a/drivers/bluetooth/btrtl.c
+++ b/drivers/bluetooth/btrtl.c
@@ -73,6 +73,7 @@ enum btrtl_chip_id {
CHIP_ID_8922A = 44,
CHIP_ID_8852BT = 47,
CHIP_ID_8761C = 51,
+ CHIP_ID_8922D = 55,
};
static const struct id_table ic_id_table[] = {
@@ -310,6 +311,15 @@ static const struct id_table ic_id_table[] = {
.cfg_name = "rtl_bt/rtl8852btu_config",
.hw_info = "rtl8852btu" },
+ /* 8922DU */
+ { IC_INFO(RTL_ROM_LMP_8922A, 0xd, 0xe, HCI_USB),
+ .config_needed = false,
+ .has_rom_version = true,
+ .has_msft_ext = true,
+ .fw_name = "rtl_bt/rtl8922du_fw",
+ .cfg_name = "rtl_bt/rtl8922du_config",
+ .hw_info = "rtl8922du" },
+
};
static const struct id_table *btrtl_match_ic(u16 lmp_subver, u16 hci_rev,
@@ -1366,6 +1376,7 @@ void btrtl_set_quirks(struct hci_dev *hdev, struct btrtl_device_info *btrtl_dev)
case CHIP_ID_8922A:
case CHIP_ID_8852BT:
case CHIP_ID_8761C:
+ case CHIP_ID_8922D:
hci_set_quirk(hdev, HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED);
/* RTL8852C needs to transmit mSBC data continuously without
@@ -1643,3 +1654,5 @@ MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw_v2.bin");
MODULE_FIRMWARE("rtl_bt/rtl8852cu_config.bin");
MODULE_FIRMWARE("rtl_bt/rtl8922au_fw.bin");
MODULE_FIRMWARE("rtl_bt/rtl8922au_config.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8922du_fw.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8922du_config.bin");
--
2.34.1
prev parent reply other threads:[~2026-11-20 8:26 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-20 8:26 [PATCH v10 0/2] Bluetooth: btrtl: Add firmware format v3 support and RTL8922D Hilda Wu
2026-11-20 8:26 ` [PATCH v10 1/2] Bluetooth: btrtl: Add firmware format v3 support Hilda Wu
2026-11-20 8:26 ` Hilda Wu [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261120082636.3834168-3-hildawu@realtek.com \
--to=hildawu@realtek.com \
--cc=alex_lu@realsil.com.cn \
--cc=arunr@valvesoftware.com \
--cc=jason_mao@realsil.com.cn \
--cc=kidman@realtek.com \
--cc=linux-bluetooth@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=luiz.dentz@gmail.com \
--cc=marcel@holtmann.org \
--cc=max.chou@realtek.com \
--cc=zoey_zhou@realsil.com.cn \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®