mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Matthew Laux <matthew.laux@gmail.com>
To: Mauro Carvalho Chehab <mchehab@kernel.org>,
	Hans Verkuil <hverkuil@kernel.org>,
	Mehdi Djait <mehdi.djait@bootlin.com>
Cc: linux-kernel@vger.kernel.org, linux-media@vger.kernel.org,
	Matthew Laux <matthew.laux@gmail.com>
Subject: [PATCH v7 07/12] media: tw9900: power down analog blocks in runtime suspend
Date: Fri, 20 Nov 2026 21:55:18 -0600	[thread overview]
Message-ID: <20261121035523.26764-8-matthew.laux@gmail.com> (raw)
In-Reply-To: <20261121035523.26764-1-matthew.laux@gmail.com>

On boards without a controllable supply or reset GPIO, runtime suspend
leaves the decoder fully powered. Set the CLK/Y/C power-down bits in
ANALOG_CTL and the PLL power-down bit in ANAL_CTL_II before cutting
power. Runtime resume rewrites both registers from the init table.

Signed-off-by: Matthew Laux <matthew.laux@gmail.com>
---
 drivers/media/i2c/tw9900.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/media/i2c/tw9900.c b/drivers/media/i2c/tw9900.c
index 585509c1b41d..b2b754e898c2 100644
--- a/drivers/media/i2c/tw9900.c
+++ b/drivers/media/i2c/tw9900.c
@@ -34,6 +34,9 @@
 #define TW9900_REG_CKHY_HSDLY			0x04
 #define TW9900_REG_OUT_CTRL_I			0x05
 #define TW9900_REG_ANALOG_CTL			0x06
+#define TW9900_REG_ANALOG_CTL_CLK_PDN		BIT(3)
+#define TW9900_REG_ANALOG_CTL_Y_PDN		BIT(2)
+#define TW9900_REG_ANALOG_CTL_C_PDN		BIT(1)
 #define TW9900_REG_CROP_HI			0x07
 #define TW9900_REG_VDELAY_LO			0x08
 #define TW9900_REG_VACTIVE_LO			0x09
@@ -48,6 +51,7 @@
 #define TW9900_REG_HUE				0x15
 #define TW9900_REG_VBI_CNTL			0x19
 #define TW9900_REG_ANAL_CTL_II			0x1A
+#define TW9900_REG_ANAL_CTL_II_PLL_PDN		BIT(6)
 #define TW9900_REG_OUT_CTRL_II			0x1B
 #define TW9900_REG_STD				0x1C
 #define TW9900_REG_STD_AUTO_PROGRESS		BIT(7)
@@ -689,6 +693,13 @@ static int tw9900_runtime_suspend(struct device *dev)
 
 	mutex_lock(&tw9900->mutex);
 
+	tw9900_write_reg(tw9900->client, TW9900_REG_ANALOG_CTL,
+			 TW9900_REG_ANALOG_CTL_CLK_PDN |
+			 TW9900_REG_ANALOG_CTL_Y_PDN |
+			 TW9900_REG_ANALOG_CTL_C_PDN);
+	tw9900_write_reg(tw9900->client, TW9900_REG_ANAL_CTL_II,
+			 TW9900_REG_ANAL_CTL_II_PLL_PDN);
+
 	if (tw9900->reset_gpio)
 		gpiod_set_value_cansleep(tw9900->reset_gpio, 1);
 
-- 
2.47.3


  parent reply	other threads:[~2026-11-21  3:55 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-21  3:55 [PATCH v7 00/12] Add driver for StarTech USB3HDCAP capture device Matthew Laux
2026-11-21  3:55 ` [PATCH v7 01/12] media: tw9900: Disable regulator on runtime resume failure Matthew Laux
2026-11-21  3:55 ` [PATCH v7 02/12] media: tw9900: release the device when stopping the stream fails Matthew Laux
2026-11-21  3:55 ` [PATCH v7 03/12] media: tw9900: accept the TW9910 chip ID Matthew Laux
2026-11-21  3:55 ` [PATCH v7 04/12] media: tw9900: add saturation, hue and sharpness controls Matthew Laux
2026-11-21  3:55 ` [PATCH v7 05/12] media: tw9900: program all mode registers in the PAL table Matthew Laux
2026-11-21  3:55 ` [PATCH v7 06/12] media: tw9900: power off the device on remove if still active Matthew Laux
2026-11-21  3:55 ` Matthew Laux [this message]
2026-11-21  3:55 ` [PATCH v7 08/12] media: tw9900: use runtime PM autosuspend Matthew Laux
2026-11-21  3:55 ` [PATCH v7 09/12] media: tw9900: allow board-specific register tables via platform data Matthew Laux
2026-11-21  3:55 ` [PATCH v7 10/12] media: tw9900: add S-Video input and progressive source detection Matthew Laux
2026-11-21  3:55 ` [PATCH v7 11/12] media: Add subdevice driver for the Mstar MST3367 HDMI receiver Matthew Laux
2026-11-21  3:55 ` [PATCH v7 12/12] media: add driver for StarTech USB3HDCAP Matthew Laux

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20261121035523.26764-8-matthew.laux@gmail.com \
    --to=matthew.laux@gmail.com \
    --cc=hverkuil@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=mchehab@kernel.org \
    --cc=mehdi.djait@bootlin.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®