From: Lucas Tanure <tanure@linux.com>
To: xianwei.zhao@amlogic.com, Andrew Lunn <andrew+netdev@lunn.ch>,
davem@davemloft.net, Eric Dumazet <edumazet@kernel.org>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Neil Armstrong <neil.armstrong@linaro.org>,
Kevin Hilman <khilman@baylibre.com>,
Jerome Brunet <jbrunet@baylibre.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Maxime Chevallier <maxime.chevallier@bootlin.com>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: netdev@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH v8 4/4] arm64: dts: amlogic: t7: khadas-vim4: enable the ethernet port
Date: Sat, 21 Nov 2026 21:31:02 +0000 [thread overview]
Message-ID: <20261121213102.143130-5-tanure@linux.com> (raw)
In-Reply-To: <20261121213102.143130-1-tanure@linux.com>
The board carries a Realtek RTL8211F gigabit PHY on the external
management bus, connected to the MAC over RGMII. Its address pins
strap it to 1; it also answers on 0, the RTL8211F broadcast address,
so the vendor tree lists 0.
Enable the controller and the management bus multiplexer, hand the
controller the ethernet pins and point it at the PHY. RGMII needs a
delay on each of its two clocks. The board traces add none, so the PHY
adds both, which is what rgmii-id asks of it.
The PHY interrupt is on GPIOH_6, so link changes are reported, not
polled. The reset is an RC network on the board, not a SoC pin: no
reset line.
Signed-off-by: Lucas Tanure <tanure@linux.com>
---
.../amlogic/amlogic-t7-a311d2-khadas-vim4.dts | 23 +++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-t7-a311d2-khadas-vim4.dts b/arch/arm64/boot/dts/amlogic/amlogic-t7-a311d2-khadas-vim4.dts
index 0fa83362b417..7b86ab2579aa 100644
--- a/arch/arm64/boot/dts/amlogic/amlogic-t7-a311d2-khadas-vim4.dts
+++ b/arch/arm64/boot/dts/amlogic/amlogic-t7-a311d2-khadas-vim4.dts
@@ -14,6 +14,7 @@
compatible = "khadas,vim4", "amlogic,a311d2", "amlogic,t7";
aliases {
+ ethernet0 = ðmac;
serial0 = &uart_a;
mmc0 = &sd_emmc_c;
mmc1 = &sd_emmc_b;
@@ -256,6 +257,28 @@
};
};
+ðmac {
+ status = "okay";
+ pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
+ pinctrl-names = "default";
+ phy-mode = "rgmii-id";
+ phy-handle = <&external_phy>;
+};
+
+ð_phy {
+ status = "okay";
+};
+
+&ext_mdio {
+ external_phy: ethernet-phy@1 {
+ /* Realtek RTL8211FD-CG */
+ reg = <1>;
+
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <GPIOH_6 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
&i2c_m_ao_a {
status = "okay";
pinctrl-0 = <&i2c0_ao_d_pins>;
--
2.56.1
prev parent reply other threads:[~2026-11-21 21:31 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-21 21:30 [PATCH v8 0/4] Add ethernet support for the Amlogic T7 Lucas Tanure
2026-11-21 21:30 ` [PATCH v8 1/4] dt-bindings: net: amlogic,g12a-mdio-mux: add the T7 compatible Lucas Tanure
2026-11-21 21:31 ` [PATCH v8 2/4] arm64: dts: amlogic: t7: add the ethernet pinctrl nodes Lucas Tanure
2026-11-21 21:31 ` [PATCH v8 3/4] arm64: dts: amlogic: t7: add the ethernet controller Lucas Tanure
2026-11-21 21:31 ` Lucas Tanure [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261121213102.143130-5-tanure@linux.com \
--to=tanure@linux.com \
--cc=alexandre.torgue@foss.st.com \
--cc=andrew+netdev@lunn.ch \
--cc=conor+dt@kernel.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edumazet@kernel.org \
--cc=jbrunet@baylibre.com \
--cc=khilman@baylibre.com \
--cc=krzk+dt@kernel.org \
--cc=kuba@kernel.org \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=maxime.chevallier@bootlin.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=neil.armstrong@linaro.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=robh@kernel.org \
--cc=xianwei.zhao@amlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®