Re: [PATCH 4/4] clk: ti: add am33xx spread spectrum clock support

[Dario Binacchi <dariobin@libero.it>]

Hi Grygorii,

> Il 16/03/2021 12:52 Grygorii Strashko <grygorii.strashko@ti.com> ha scritto:
> 
>  
> On 14/03/2021 17:12, Dario Binacchi wrote:
> > The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
> > As reported by the TI spruh73x RM, SSC is only supported for the
> > DISP/LCD and MPU PLLs on am33xx device. SSC is not supported for DDR,
> > PER, and CORE PLLs.
> > 
> > Calculating the required values and setting the registers accordingly
> > was taken from the set_mpu_spreadspectrum routine contained in the
> > arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
> > 
> > In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
> > SSC enabled, the AM335x reference manual explains that there is a
> > restriction of range of M values. Since the omap2_dpll_round_rate
> > routine attempts to select the minimum possible N, the value of M
> > obtained is not guaranteed to be within the range required. With the new
> > "ti,min-div" parameter it is possible to increase N and consequently M
> > to satisfy the constraint imposed by SSC.
> > 
> > Signed-off-by: Dario Binacchi <dariobin@libero.it>
> > 
> > ---
> > 
> >   arch/arm/boot/dts/am33xx-clocks.dtsi |  4 +-
> >   drivers/clk/ti/dpll.c                | 41 ++++++++++++++
> >   drivers/clk/ti/dpll3xxx.c            | 85 ++++++++++++++++++++++++++++
> >   include/linux/clk/ti.h               | 24 ++++++++
> >   4 files changed, 152 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/arm/boot/dts/am33xx-clocks.dtsi b/arch/arm/boot/dts/am33xx-clocks.dtsi
> > index e7bbbf536a8c..a02e0b1229a4 100644
> > --- a/arch/arm/boot/dts/am33xx-clocks.dtsi
> > +++ b/arch/arm/boot/dts/am33xx-clocks.dtsi
> > @@ -164,7 +164,7 @@
> >   		#clock-cells = <0>;
> >   		compatible = "ti,am3-dpll-core-clock";
> >   		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
> > -		reg = <0x0490>, <0x045c>, <0x0468>, <0x0460>, <0x0464>;
> > +		reg = <0x0490>, <0x045c>, <0x0468>;
> >   	};
> >   
> >   	dpll_core_x2_ck: dpll_core_x2_ck {
> > @@ -204,7 +204,7 @@
> >   		#clock-cells = <0>;
> >   		compatible = "ti,am3-dpll-clock";
> >   		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
> > -		reg = <0x0488>, <0x0420>, <0x042c>;
> > +		reg = <0x0488>, <0x0420>, <0x042c>, <0x0424>, <0x0428>;
> >   	};
> 
> You can't mix DT vs code.

Right, I forgot to remove it during a rebase of the series.

> 
> >   
> >   	dpll_mpu_m2_ck: dpll_mpu_m2_ck@4a8 {
> > diff --git a/drivers/clk/ti/dpll.c b/drivers/clk/ti/dpll.c
> > index d6f1ac5b53e1..2738417a47b7 100644
> > --- a/drivers/clk/ti/dpll.c
> > +++ b/drivers/clk/ti/dpll.c
> > @@ -290,7 +290,9 @@ static void __init of_ti_dpll_setup(struct device_node *node,
> >   	struct clk_init_data *init = NULL;
> >   	const char **parent_names = NULL;
> >   	struct dpll_data *dd = NULL;
> > +	int ssc_clk_index;
> >   	u8 dpll_mode = 0;
> > +	u32 min_div;
> >   
> >   	dd = kmemdup(ddt, sizeof(*dd), GFP_KERNEL);
> >   	clk_hw = kzalloc(sizeof(*clk_hw), GFP_KERNEL);
> > @@ -345,6 +347,27 @@ static void __init of_ti_dpll_setup(struct device_node *node,
> >   	if (dd->autoidle_mask) {
> >   		if (ti_clk_get_reg_addr(node, 3, &dd->autoidle_reg))
> >   			goto cleanup;
> > +
> > +		ssc_clk_index = 4;
> > +	} else {
> > +		ssc_clk_index = 3;
> > +	}
> > +
> > +	if (dd->ssc_deltam_int_mask && dd->ssc_deltam_frac_mask &&
> > +	    dd->ssc_modfreq_mant_mask && dd->ssc_modfreq_exp_mask) {
> > +		if (ti_clk_get_reg_addr(node, ssc_clk_index++,
> > +					&dd->ssc_deltam_reg))
> > +			goto cleanup;
> > +
> > +		if (ti_clk_get_reg_addr(node, ssc_clk_index++,
> > +					&dd->ssc_modfreq_reg))
> > +			goto cleanup;
> > +
> > +		of_property_read_u32(node, "ti,ssc-modfreq", &dd->ssc_modfreq);
> > +		of_property_read_u32(node, "ti,ssc-deltam", &dd->ssc_deltam);
> > +		if (of_property_read_bool(node, "ti,ssc-downspread"))
> > +			dd->ssc_downspread = 1;
> 
> New bindings.

I added the bindings documentation in another patch of the series.

Thanks and regards,
Dario
> 
> > +
> >   	}
> >   
> >   	if (of_property_read_bool(node, "ti,low-power-stop"))
> > @@ -356,6 +379,10 @@ static void __init of_ti_dpll_setup(struct device_node *node,
> >   	if (of_property_read_bool(node, "ti,lock"))
> >   		dpll_mode |= 1 << DPLL_LOCKED;
> >   
> > +	if (!of_property_read_u32(node, "ti,min-div", &min_div) &&
> > +	    min_div > dd->min_divider)
> > +		dd->min_divider = min_div;
> > +
> 
> New bindings.
> 
> [...]
> 
> -- 
> Best regards,
> grygorii