Re: [PATCH v2 2/2] phy: cadence: cdns-dphy: Update calibration wait time for startup state machine

[Devarsh Thakkar <devarsht@ti.com>]

Hi Tomi,

Thanks for the review.

On 02/04/25 17:12, Tomi Valkeinen wrote:
> Hi,
> 
> On 26/03/2025 17:23, Devarsh Thakkar wrote:
>> Use system characterized reset value specified in TRM [1] to program
>> calibration wait time which defines number of cycles to wait for after
>> startup state machine is in bandgap enable state.
>>
>> This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
>> AM62L and J721E SoC [2].
>>
>> [1] AM62P TRM (Section ):
>> https://www.ti.com/lit/pdf/spruj83
>>
>> [2]:
>> Link: https://gist.github.com/devarsht/89e4830e886774fcd50aa6e29cce3a79
>>
>> Cc: stable@vger.kernel.org
>> Fixes: 7a343c8bf4b5 ("phy: Add Cadence D-PHY support")
>> Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
>> ---
>> V2: Introduced this as as separate patch
>>
>>   drivers/phy/cadence/cdns-dphy.c | 3 +++
>>   1 file changed, 3 insertions(+)
>>
>> diff --git a/drivers/phy/cadence/cdns-dphy.c 
>> b/drivers/phy/cadence/cdns-dphy.c
>> index c4de9e4d3e93..11fbffe5aafd 100644
>> --- a/drivers/phy/cadence/cdns-dphy.c
>> +++ b/drivers/phy/cadence/cdns-dphy.c
>> @@ -30,6 +30,7 @@
>>   #define DPHY_CMN_SSM            DPHY_PMA_CMN(0x20)
>>   #define DPHY_CMN_SSM_EN            BIT(0)
>> +#define DPHY_CMN_SSM_CAL_WAIT_TIME    GENMASK(8, 1)
>>   #define DPHY_CMN_TX_MODE_EN        BIT(9)
>>   #define DPHY_CMN_PWM            DPHY_PMA_CMN(0x40)
>> @@ -405,6 +406,8 @@ static int cdns_dphy_configure(struct phy *phy, 
>> union phy_configure_opts *opts)
>>       reg = FIELD_PREP(DPHY_BAND_CFG_LEFT_BAND, band_ctrl) |
>>             FIELD_PREP(DPHY_BAND_CFG_RIGHT_BAND, band_ctrl);
>>       writel(reg, dphy->regs + DPHY_BAND_CFG);
>> +    writel(FIELD_PREP(DPHY_CMN_SSM_CAL_WAIT_TIME, 0x14) | 
>> DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
>> +           dphy->regs + DPHY_CMN_SSM);
> 
> This sounds like a TI specific characterized value, but the function 
> here is a generic one. Also, is the value same for all TI SoCs? Or is it 
> per-soc?
> 

No this is not TI specific value. As mentioned in commit message, 0x14 
is the cadence characterized default value for calibration wait time 
which they put in as reset value in the IP (if you reset the IP you will 
see calibration wait time as 0x14) to be used by software for optimal 
initialization.

Regards
Devarsh