Re: [RFC PATCH V2 net-next 03/11] net: hibmcge: Add mdio and hardware configuration supported in this module

[Andrew Lunn <andrew@lunn.ch>]

> +int hbg_hw_adjust_link(struct hbg_priv *priv, u32 speed, u32 duplex)
> +{
> +	if (speed != HBG_PORT_MODE_SGMII_10M &&
> +	    speed != HBG_PORT_MODE_SGMII_100M &&
> +	    speed != HBG_PORT_MODE_SGMII_1000M)
> +		return -EOPNOTSUPP;
> +
> +	if (duplex != DUPLEX_FULL && duplex != DUPLEX_HALF)
> +		return -EOPNOTSUPP;


Can this happen? We try to avoid defensive code, preferring to ensure
it can never happen. So long as you have told phylib the limits of
your hardware, it should enforce these.

> @@ -26,11 +27,11 @@ static int hbg_init(struct hbg_priv *priv)
>  		return dev_err_probe(dev, PTR_ERR(regmap), "failed to init regmap\n");
>  
>  	priv->regmap = regmap;
> -	ret = hbg_hw_event_notify(priv, HBG_HW_EVENT_INIT);
> +	ret = hbg_hw_init(priv);
>  	if (ret)
>  		return ret;
>  
> -	return hbg_hw_dev_specs_init(priv);
> +	return hbg_mdio_init(priv);

I've not read the previous patches, but that looks odd. Why is code
you just added in previous patches getting replaced?

> +static int hbg_phy_connect(struct hbg_priv *priv)
> +{
> +	struct phy_device *phydev = priv->mac.phydev;
> +	struct device *dev = &priv->pdev->dev;
> +	struct hbg_mac *mac = &priv->mac;
> +	int ret;
> +
> +	ret = phy_connect_direct(priv->netdev, mac->phydev, hbg_phy_adjust_link,
> +				 PHY_INTERFACE_MODE_SGMII);
> +	if (ret)
> +		return dev_err_probe(dev, -ENOMEM, "failed to connect phy\n");

Don't replace the error code. Doing so actually makes dev_err_probe()
pointless because it is not going to see the EPROBE_DEFER.


> +int hbg_mdio_init(struct hbg_priv *priv)
> +{
> +	struct device *dev = &priv->pdev->dev;
> +	struct hbg_mac *mac = &priv->mac;
> +	struct phy_device *phydev;
> +	struct mii_bus *mdio_bus;
> +	int ret;
> +
> +	mac->phy_addr = priv->dev_specs.phy_addr;
> +	mdio_bus = devm_mdiobus_alloc(dev);
> +	if (!mdio_bus)
> +		return dev_err_probe(dev, -ENOMEM, "failed to alloc MDIO bus\n");
> +
> +	mdio_bus->parent = dev;
> +	mdio_bus->priv = priv;
> +	mdio_bus->phy_mask = ~(1 << mac->phy_addr);
> +	mdio_bus->name = "hibmcge mii bus";
> +	mac->mdio_bus = mdio_bus;
> +
> +	mdio_bus->read = hbg_mdio_read22;
> +	mdio_bus->write = hbg_mdio_write22;
> +	snprintf(mdio_bus->id, MII_BUS_ID_SIZE, "%s-%s", "mii", dev_name(dev));
> +
> +	ret = devm_mdiobus_register(dev, mdio_bus);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "failed to register MDIO bus\n");
> +
> +	phydev = mdiobus_get_phy(mdio_bus, mac->phy_addr);
> +	if (!phydev)
> +		return dev_err_probe(dev, -EIO, "failed to get phy device\n");

ENODEV is probably better, since the device does not exist.

	Andrew