From: Dave Hansen <dave.hansen@intel.com>
To: Tom Lendacky <thomas.lendacky@amd.com>,
Borislav Petkov <bp@alien8.de>,
"Shutemov, Kirill" <kirill.shutemov@intel.com>,
Ashish Kalra <ashish.kalra@amd.com>,
Kai Huang <kai.huang@intel.com>
Cc: LKML <linux-kernel@vger.kernel.org>,
the arch/x86 maintainers <x86@kernel.org>
Subject: Re: AMD Memory encryption vs. kexec
Date: Wed, 29 Nov 2023 12:01:42 -0800 [thread overview]
Message-ID: <26d91827-8308-42e2-969e-993c82623bb0@intel.com> (raw)
In-Reply-To: <29e235f7-add2-47ae-b06e-a717202c4faf@amd.com>
On 11/28/23 06:03, Tom Lendacky wrote:
...
>> By my reading, the CC_ATTR_HOST_MEM_ENCRYPT is basically a check for
>> whether the current kernel has enabled SME but not SEV while the
>> stop_this_cpu() site is driven purely by whether the hardware *supports*
>> SME.
>>
>> The whole supposed reason stop_this_cpu() checks CPUID directly is that
>> the current kernel SME/SEV enabling might not match the _next_ kernel's
>> enabling choices.
>
> Correct.
>
>> So, why is a _current_ kernel check OK for relocate_kernel(), but not OK
>> for stop_this_cpu()?
>
> The relocate_kernel() check provides an indication of whether SME is
> actually active. The kexec kernel is placed in unencrypted memory to
> match how the system was booted - where the kernel is loaded into
> unencrypted memory and then encrypted in-place if SME is desired
> (mem_encrypt=on). Since the kexec kernel will be unencrypted, the
> cc_platform_has() call is used to indicate whether to perform a wbinvd
> to remove encrypted cache line entries. If SME is not active, then there
> is no need to flush caches prior to booting the kexec kernel.
Ahh, so that wbinvd is truly specific to kexec. It protects the
always-unencrypted kexec area from being zapped by encrypted lines. It
isn't necessary when the old kexec kernel is mem_encrypt=off because the
unencrypted old kernel matches the always unencrypted kexec area.
What I was worried about was the _larger_ case. Not the kexec area, the
*rest* of memory. But I think that's irrelevant because there's yet
*another* wbinvd in __enc_copy() that is will flush the rest of memory
when going from mem_encrypt=off=>on.
I'd like to propose a simplification. Let's add a
CC_ATTR_HOST_MEM_INCOHERENT. That bit gets set on all hardware that
needs WBVINDs at kexec. On AMD, it can use the stop_this_cpu() logic.
This will cause an additional wbinvd in case where a mem_encrypt=off
kernel is kexec'ing.
We can also set it on any TDX-enabled Intel hardware.
That leads to very simple logic at kexec:
Could the old kernel leave incoherent caches
around? If so, do WBINVD.
That logic gets applied to all CPUs, both boot and secondary. It
applies to all the SME-only systems (currently CC_ATTR_HOST_MEM_ENCRYPT)
and also all TDX systems. It would not depend on the current kernel's
SME enabling and it would allow both kexec-related sites to share the
same logic.
I don't really like the idea of yet another CC_ATTR_HOST_MEM_INCOHERENT
bit, but I do think it's better than adding some TDX-specific paths.
next prev parent reply other threads:[~2023-11-29 20:02 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-28 0:00 Dave Hansen
2023-11-28 14:03 ` Tom Lendacky
2023-11-29 20:01 ` Dave Hansen [this message]
2023-11-29 20:54 ` Tom Lendacky
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=26d91827-8308-42e2-969e-993c82623bb0@intel.com \
--to=dave.hansen@intel.com \
--cc=ashish.kalra@amd.com \
--cc=bp@alien8.de \
--cc=kai.huang@intel.com \
--cc=kirill.shutemov@intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=thomas.lendacky@amd.com \
--cc=x86@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®