From: <sean.wang@mediatek.com>
To: <robh+dt@kernel.org>, <matthias.bgg@gmail.com>,
<mark.rutland@arm.com>, <devicetree@vger.kernel.org>,
<linux-mediatek@lists.infradead.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>,
Sean Wang <sean.wang@mediatek.com>
Subject: [PATCH v2 12/12] arm: dts: mt7623: add MT7623N reference board with eMMC
Date: Wed, 11 Apr 2018 16:54:05 +0800 [thread overview]
Message-ID: <28e5f34ba9ef35bfd9e3ffd7ff53506dab4a5cde.1523434758.git.sean.wang@mediatek.com> (raw)
In-Reply-To: <cover.1523434757.git.sean.wang@mediatek.com>
From: Sean Wang <sean.wang@mediatek.com>
Add MT7623N reference board with eMMC. On the board, there is additional
external PHY ICPlus IP1001 transceiver available by port 5 on the MDIO
bus connectted with GMAC2.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/mt7623.dtsi | 17 ++
arch/arm/boot/dts/mt7623n-rfb-emmc.dts | 326 +++++++++++++++++++++++++++++++++
3 files changed, 344 insertions(+)
create mode 100644 arch/arm/boot/dts/mt7623n-rfb-emmc.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index bc33a3c..19013d4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1152,6 +1152,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt6592-evb.dtb \
mt7623a-rfb-emmc.dtb \
mt7623a-rfb-nand.dtb \
+ mt7623n-rfb-emmc.dtb \
mt7623n-rfb-nand.dtb \
mt7623n-bananapi-bpi-r2.dtb \
mt8127-moose.dtb \
diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mt7623.dtsi
index f84c37b..d1eb123 100644
--- a/arch/arm/boot/dts/mt7623.dtsi
+++ b/arch/arm/boot/dts/mt7623.dtsi
@@ -968,6 +968,14 @@
};
};
+ i2c2_pins_a: i2c2-default {
+ pin-i2c2 {
+ pinmux = <MT7623_PIN_77_SDA2_FUNC_SDA2>,
+ <MT7623_PIN_78_SCL2_FUNC_SCL2>;
+ bias-disable;
+ };
+ };
+
i2c2_pins_b: i2c2-alt {
pin-i2c2 {
pinmux = <MT7623_PIN_122_GPIO122_FUNC_SDA2>,
@@ -1185,6 +1193,15 @@
};
};
+ spi2_pins_a: spi2-default {
+ pins-spi {
+ pinmux = <MT7623_PIN_101_SPI2_CSN_FUNC_SPI2_CS>,
+ <MT7623_PIN_104_SPI2_CK_FUNC_SPI2_CK>,
+ <MT7623_PIN_102_SPI2_MI_FUNC_SPI2_MI>,
+ <MT7623_PIN_103_SPI2_MO_FUNC_SPI2_MO>;
+ };
+ };
+
uart0_pins_a: uart0-default {
pins-dat {
pinmux = <MT7623_PIN_79_URXD0_FUNC_URXD0>,
diff --git a/arch/arm/boot/dts/mt7623n-rfb-emmc.dts b/arch/arm/boot/dts/mt7623n-rfb-emmc.dts
new file mode 100644
index 0000000..b760613
--- /dev/null
+++ b/arch/arm/boot/dts/mt7623n-rfb-emmc.dts
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017-2018 MediaTek Inc.
+ * Author: Sean Wang <sean.wang@mediatek.com>
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "mt7623.dtsi"
+#include "mt6323.dtsi"
+
+/ {
+ model = "MediaTek MT7623N with eMMC reference board";
+ compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ cpus {
+ cpu@0 {
+ proc-supply = <&mt6323_vproc_reg>;
+ };
+
+ cpu@1 {
+ proc-supply = <&mt6323_vproc_reg>;
+ };
+
+ cpu@2 {
+ proc-supply = <&mt6323_vproc_reg>;
+ };
+
+ cpu@3 {
+ proc-supply = <&mt6323_vproc_reg>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&key_pins_a>;
+
+ factory {
+ label = "factory";
+ linux,code = <BTN_0>;
+ gpios = <&pio 256 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0 0x80000000 0 0x40000000>;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "mediatek,mt2701-wm8960-machine";
+ mediatek,platform = <&afe>;
+ audio-routing =
+ "Headphone", "HP_L",
+ "Headphone", "HP_R",
+ "LINPUT1", "AMIC",
+ "RINPUT1", "AMIC";
+ mediatek,audio-codec = <&wm8960>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_pins_a>;
+ };
+};
+
+&btif {
+ status = "okay";
+};
+
+&cir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cir_pins_a>;
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "trgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-handle = <&phy5>;
+ };
+
+ mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ phy-mode = "rgmii-rxid";
+ };
+
+ switch@0 {
+ compatible = "mediatek,mt7530";
+ reg = <0>;
+ reset-gpios = <&pio 33 0>;
+ core-supply = <&mt6323_vpa_reg>;
+ io-supply = <&mt6323_vemc3v3_reg>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "trgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_b>;
+ status = "okay";
+
+ wm8960: wm8960@1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_pins_default>;
+ pinctrl-1 = <&mmc0_pins_uhs>;
+ status = "okay";
+ bus-width = <8>;
+ max-frequency = <50000000>;
+ cap-mmc-highspeed;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ non-removable;
+};
+
+&mmc1 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_uhs>;
+ status = "okay";
+ bus-width = <4>;
+ max-frequency = <50000000>;
+ cap-sd-highspeed;
+ cd-gpios = <&pio 261 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_3p3v>;
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_default>;
+ status = "okay";
+
+ pcie@0,0 {
+ status = "okay";
+ };
+
+ pcie@1,0 {
+ status = "okay";
+ };
+};
+
+&pcie0_phy {
+ status = "okay";
+};
+
+&pcie1_phy {
+ status = "okay";
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pins_a>;
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>;
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins_a>;
+ status = "okay";
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+};
+
+&usb1 {
+ vusb33-supply = <®_3p3v>;
+ vbus-supply = <®_5v>;
+ status = "okay";
+};
+
+&u3phy1 {
+ status = "okay";
+};
--
2.7.4
next prev parent reply other threads:[~2018-04-11 8:55 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-04-11 8:53 [PATCH v2 00/12] refactor dts and add support for more boards sean.wang
2018-04-11 8:53 ` [PATCH v2 01/12] dt-bindings: cpufreq: mediatek: use - instead of _ in examples sean.wang
2018-05-02 8:59 ` Matthias Brugger
2018-04-11 8:53 ` [PATCH v2 02/12] arm: dts: mediatek: converted to using SPDX identifiers sean.wang
2018-04-11 8:53 ` [PATCH v2 03/12] arm: dts: mt7623: fix invalid memory node being generated sean.wang
2018-05-11 15:03 ` Matthias Brugger
2018-05-12 5:28 ` Sean Wang
2018-04-11 8:53 ` [PATCH v2 04/12] arm: dts: mt7623: fix available memory size on bananapi-r2 sean.wang
2018-04-11 8:53 ` [PATCH v2 05/12] arm: dts: mt7623: fix all Warnings (unit_address_vs_reg) sean.wang
2018-04-11 8:53 ` [PATCH v2 06/12] arm: dts: mt7623: add BTIF, HSDMA and SPI-NOR device nodes sean.wang
2018-04-11 8:54 ` [PATCH v2 07/12] arm: dts: mt6323: move node mt6323 leds to mt6323.dtsi sean.wang
2018-04-11 8:54 ` [PATCH v2 08/12] arm: dts: mediatek: modify audio related nodes for both MT2701 and MT7623 sean.wang
2018-04-11 8:54 ` [PATCH v2 09/12] arm: dts: mt7623: extend common file reused by all boards with MT7623 SoCs sean.wang
2018-04-11 8:54 ` [PATCH v2 10/12] arm: dts: mt7623: add MT7623A SoC level DTS sean.wang
2018-04-11 8:54 ` [PATCH v2 11/12] arm: dts: mt7623: add MT7623A reference boards sean.wang
2018-04-11 8:54 ` sean.wang [this message]
2018-05-11 16:40 ` [PATCH v2 00/12] refactor dts and add support for more boards Matthias Brugger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=28e5f34ba9ef35bfd9e3ffd7ff53506dab4a5cde.1523434758.git.sean.wang@mediatek.com \
--to=sean.wang@mediatek.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®