mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Asmaa Mnebhi <asmaa@nvidia.com>
To: <andy.shevchenko@gmail.com>, <linus.walleij@linaro.org>,
	<bgolaszewski@baylibre.com>, <linux-gpio@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, <linux-acpi@vger.kernel.org>
Cc: Asmaa Mnebhi <asmaa@nvidia.com>
Subject: [PATCH v4 1/2] gpio: gpio-mlxbf3: Add gpio driver support
Date: Fri, 17 Feb 2023 16:26:50 -0500	[thread overview]
Message-ID: <28f0d670407c127614b64d9c382b11c795f5077d.1676668853.git.asmaa@nvidia.com> (raw)
In-Reply-To: <cover.1676668853.git.asmaa@nvidia.com>

Add support for the BlueField-3 SoC GPIO driver.
This driver configures and handles GPIO interrupts. It also enables a user
to manipulate certain GPIO pins via libgpiod tools or other kernel drivers.
The usables pins are defined via the gpio-reserved-ranges property.

Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
---
 drivers/gpio/Kconfig       |  12 ++
 drivers/gpio/Makefile      |   1 +
 drivers/gpio/gpio-mlxbf3.c | 230 +++++++++++++++++++++++++++++++++++++
 3 files changed, 243 insertions(+)
 create mode 100644 drivers/gpio/gpio-mlxbf3.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index ec7cfd4f52b1..5cddcb56353d 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -1534,6 +1534,18 @@ config GPIO_MLXBF2
 	help
 	  Say Y here if you want GPIO support on Mellanox BlueField 2 SoC.
 
+config GPIO_MLXBF3
+	tristate "Mellanox BlueField 3 SoC GPIO"
+	depends on (MELLANOX_PLATFORM && ARM64 && ACPI) || (64BIT && COMPILE_TEST)
+	select GPIO_GENERIC
+	help
+	  Say Y if you want GPIO support on Mellanox BlueField 3 SoC.
+	  This GPIO controller supports interrupt handling and enables the
+	  manipulation of certain GPIO pins.
+	  This controller should be used in parallel with pinctrl-mlxbf to
+	  control the desired gpios.
+	  This driver can also be built as a module called mlxbf3-gpio.
+
 config GPIO_ML_IOH
 	tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
 	depends on X86 || COMPILE_TEST
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 010587025fc8..76545ca31457 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -101,6 +101,7 @@ obj-$(CONFIG_GPIO_MERRIFIELD)		+= gpio-merrifield.o
 obj-$(CONFIG_GPIO_ML_IOH)		+= gpio-ml-ioh.o
 obj-$(CONFIG_GPIO_MLXBF)		+= gpio-mlxbf.o
 obj-$(CONFIG_GPIO_MLXBF2)		+= gpio-mlxbf2.o
+obj-$(CONFIG_GPIO_MLXBF3)		+= gpio-mlxbf3.o
 obj-$(CONFIG_GPIO_MM_LANTIQ)		+= gpio-mm-lantiq.o
 obj-$(CONFIG_GPIO_MOCKUP)		+= gpio-mockup.o
 obj-$(CONFIG_GPIO_MOXTET)		+= gpio-moxtet.o
diff --git a/drivers/gpio/gpio-mlxbf3.c b/drivers/gpio/gpio-mlxbf3.c
new file mode 100644
index 000000000000..cdc93c8e77ff
--- /dev/null
+++ b/drivers/gpio/gpio-mlxbf3.c
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0-only or BSD-3-Clause
+/* Copyright (C) 2022 NVIDIA CORPORATION & AFFILIATES */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/resource.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <linux/version.h>
+
+/*
+ * There are 2 YU GPIO blocks:
+ * gpio[0]: HOST_GPIO0->HOST_GPIO31
+ * gpio[1]: HOST_GPIO32->HOST_GPIO55
+ */
+#define MLXBF3_GPIO_MAX_PINS_PER_BLOCK 32
+
+/*
+ * fw_gpio[x] block registers and their offset
+ */
+#define MLXBF_GPIO_FW_OUTPUT_ENABLE_SET	  0x04
+#define MLXBF_GPIO_FW_DATA_OUT_SET        0x08
+#define MLXBF_GPIO_FW_OUTPUT_ENABLE_CLEAR 0x18
+#define MLXBF_GPIO_FW_DATA_OUT_CLEAR      0x1c
+#define MLXBF_GPIO_CAUSE_RISE_EN          0x28
+#define MLXBF_GPIO_CAUSE_FALL_EN          0x2c
+#define MLXBF_GPIO_READ_DATA_IN           0x30
+
+#define MLXBF_GPIO_CAUSE_OR_CAUSE_EVTEN0  0x00
+#define MLXBF_GPIO_CAUSE_OR_EVTEN0        0x14
+#define MLXBF_GPIO_CAUSE_OR_CLRCAUSE      0x18
+
+struct mlxbf3_gpio_context {
+	struct gpio_chip gc;
+
+	/* YU GPIO block address */
+	void __iomem *gpio_io;
+
+	/* YU GPIO cause block address */
+	void __iomem *gpio_cause_io;
+};
+
+static void mlxbf3_gpio_irq_enable(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct mlxbf3_gpio_context *gs = gpiochip_get_data(gc);
+	int offset = irqd_to_hwirq(irqd);
+	unsigned long flags;
+	u32 val;
+
+	raw_spin_lock_irqsave(&gs->gc.bgpio_lock, flags);
+	writel(BIT(offset), gs->gpio_cause_io + MLXBF_GPIO_CAUSE_OR_CLRCAUSE);
+
+	val = readl(gs->gpio_cause_io + MLXBF_GPIO_CAUSE_OR_EVTEN0);
+	val |= BIT(offset);
+	writel(val, gs->gpio_cause_io + MLXBF_GPIO_CAUSE_OR_EVTEN0);
+	raw_spin_unlock_irqrestore(&gs->gc.bgpio_lock, flags);
+}
+
+static void mlxbf3_gpio_irq_disable(struct irq_data *irqd)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct mlxbf3_gpio_context *gs = gpiochip_get_data(gc);
+	int offset = irqd_to_hwirq(irqd);
+	unsigned long flags;
+	u32 val;
+
+	raw_spin_lock_irqsave(&gs->gc.bgpio_lock, flags);
+	val = readl(gs->gpio_cause_io + MLXBF_GPIO_CAUSE_OR_EVTEN0);
+	val &= ~BIT(offset);
+	writel(val, gs->gpio_cause_io + MLXBF_GPIO_CAUSE_OR_EVTEN0);
+	raw_spin_unlock_irqrestore(&gs->gc.bgpio_lock, flags);
+}
+
+static irqreturn_t mlxbf3_gpio_irq_handler(int irq, void *ptr)
+{
+	struct mlxbf3_gpio_context *gs = ptr;
+	struct gpio_chip *gc = &gs->gc;
+	unsigned long pending;
+	u32 level;
+
+	pending = readl(gs->gpio_cause_io + MLXBF_GPIO_CAUSE_OR_CAUSE_EVTEN0);
+	writel(pending, gs->gpio_cause_io + MLXBF_GPIO_CAUSE_OR_CLRCAUSE);
+
+	for_each_set_bit(level, &pending, gc->ngpio)
+		generic_handle_domain_irq(gc->irq.domain, level);
+
+	return IRQ_RETVAL(pending);
+}
+
+static int
+mlxbf3_gpio_irq_set_type(struct irq_data *irqd, unsigned int type)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+	struct mlxbf3_gpio_context *gs = gpiochip_get_data(gc);
+	int offset = irqd_to_hwirq(irqd);
+	unsigned long flags;
+	u32 val;
+
+	raw_spin_lock_irqsave(&gs->gc.bgpio_lock, flags);
+
+	switch (type & IRQ_TYPE_SENSE_MASK) {
+	case IRQ_TYPE_EDGE_BOTH:
+		val = readl(gs->gpio_io + MLXBF_GPIO_CAUSE_FALL_EN);
+		val |= BIT(offset);
+		writel(val, gs->gpio_io + MLXBF_GPIO_CAUSE_FALL_EN);
+		val = readl(gs->gpio_io + MLXBF_GPIO_CAUSE_RISE_EN);
+		val |= BIT(offset);
+		writel(val, gs->gpio_io + MLXBF_GPIO_CAUSE_RISE_EN);
+		break;
+	case IRQ_TYPE_EDGE_RISING:
+		val = readl(gs->gpio_io + MLXBF_GPIO_CAUSE_RISE_EN);
+		val |= BIT(offset);
+		writel(val, gs->gpio_io + MLXBF_GPIO_CAUSE_RISE_EN);
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		val = readl(gs->gpio_io + MLXBF_GPIO_CAUSE_FALL_EN);
+		val |= BIT(offset);
+		writel(val, gs->gpio_io + MLXBF_GPIO_CAUSE_FALL_EN);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	raw_spin_unlock_irqrestore(&gs->gc.bgpio_lock, flags);
+
+	irq_set_handler_locked(irqd, handle_simple_irq);
+
+	return 0;
+}
+
+static const struct irq_chip gpio_mlxbf3_irqchip = {
+	.name = "MLNXBF33",
+	.irq_set_type = mlxbf3_gpio_irq_set_type,
+	.irq_enable = mlxbf3_gpio_irq_enable,
+	.irq_disable = mlxbf3_gpio_irq_disable,
+};
+
+static int
+mlxbf3_gpio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mlxbf3_gpio_context *gs;
+	struct gpio_irq_chip *girq;
+	struct gpio_chip *gc;
+	unsigned int npins;
+	int ret, irq;
+
+	gs = devm_kzalloc(dev, sizeof(*gs), GFP_KERNEL);
+	if (!gs)
+		return -ENOMEM;
+
+	gs->gpio_io = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(gs->gpio_io))
+		return PTR_ERR(gs->gpio_io);
+
+	gs->gpio_cause_io = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(gs->gpio_cause_io))
+		return PTR_ERR(gs->gpio_cause_io);
+
+	npins = MLXBF3_GPIO_MAX_PINS_PER_BLOCK;
+	device_property_read_u32(dev, "npins", &npins);
+
+	gc = &gs->gc;
+
+	ret = bgpio_init(gc, dev, 4,
+			gs->gpio_io + MLXBF_GPIO_READ_DATA_IN,
+			gs->gpio_io + MLXBF_GPIO_FW_DATA_OUT_SET,
+			gs->gpio_io + MLXBF_GPIO_FW_DATA_OUT_CLEAR,
+			gs->gpio_io + MLXBF_GPIO_FW_OUTPUT_ENABLE_SET,
+			gs->gpio_io + MLXBF_GPIO_FW_OUTPUT_ENABLE_CLEAR, 0);
+
+	gc->request = gpiochip_generic_request;
+	gc->free = gpiochip_generic_free;
+
+	gc->ngpio = npins;
+	gc->owner = THIS_MODULE;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq >= 0) {
+		girq = &gs->gc.irq;
+		gpio_irq_chip_set_chip(girq, &gpio_mlxbf3_irqchip);
+		girq->default_type = IRQ_TYPE_NONE;
+		/* This will let us handle the parent IRQ in the driver */
+		girq->num_parents = 0;
+		girq->parents = NULL;
+		girq->parent_handler = NULL;
+
+		/*
+		 * Directly request the irq here instead of passing
+		 * a flow-handler because the irq is shared.
+		 */
+		ret = devm_request_irq(dev, irq, mlxbf3_gpio_irq_handler,
+				       IRQF_SHARED, dev_name(dev), gs);
+		if (ret)
+			return dev_err_probe(dev, ret, "failed to request IRQ");
+	}
+
+	platform_set_drvdata(pdev, gs);
+
+	ret = devm_gpiochip_add_data(dev, &gs->gc, gs);
+	if (ret)
+		dev_err_probe(dev, ret, "Failed adding memory mapped gpiochip\n");
+
+	return 0;
+}
+
+static const struct acpi_device_id __maybe_unused mlxbf3_gpio_acpi_match[] = {
+	{ "MLNXBF33", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(acpi, mlxbf3_gpio_acpi_match);
+
+static struct platform_driver mlxbf3_gpio_driver = {
+	.driver = {
+		.name = "mlxbf3_gpio",
+		.acpi_match_table = mlxbf3_gpio_acpi_match,
+	},
+	.probe    = mlxbf3_gpio_probe,
+};
+module_platform_driver(mlxbf3_gpio_driver);
+
+MODULE_DESCRIPTION("NVIDIA BlueField-3 GPIO Driver");
+MODULE_AUTHOR("Asmaa Mnebhi <asmaa@nvidia.com>");
+MODULE_LICENSE("Dual BSD/GPL");
-- 
2.30.1


  reply	other threads:[~2023-02-17 21:27 UTC|newest]

Thread overview: 35+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-02-10 15:39 [PATCH v3 0/2] Add NVIDIA BlueField-3 GPIO driver and pin controller Asmaa Mnebhi
2023-02-10 15:39 ` [PATCH v3 1/2] Support NVIDIA BlueField-3 GPIO controller Asmaa Mnebhi
2023-02-11  7:37   ` kernel test robot
2023-02-11 11:51   ` Andy Shevchenko
2023-02-13 23:14     ` Asmaa Mnebhi
2023-02-13 23:39       ` andy.shevchenko
2023-02-10 15:39 ` [PATCH v3 2/2] Support NVIDIA BlueField-3 pinctrl driver Asmaa Mnebhi
2023-02-11 11:55   ` Andy Shevchenko
2023-02-16 17:50     ` Asmaa Mnebhi
2023-02-16 18:38       ` Andy Shevchenko
2023-02-16 18:44         ` Asmaa Mnebhi
2023-02-16 18:53           ` Andy Shevchenko
2023-02-16 19:26             ` Asmaa Mnebhi
2023-02-11 11:58 ` [PATCH v3 0/2] Add NVIDIA BlueField-3 GPIO driver and pin controller Andy Shevchenko
2023-02-17 21:26 ` [PATCH v4 0/2] Support Nvidia " Asmaa Mnebhi
2023-02-17 21:26   ` Asmaa Mnebhi [this message]
2023-02-17 23:07     ` [PATCH v4 1/2] gpio: gpio-mlxbf3: Add gpio driver support Andy Shevchenko
2023-02-22 18:40       ` Asmaa Mnebhi
2023-02-23 11:06         ` Andy Shevchenko
2023-02-23 19:08           ` Asmaa Mnebhi
2023-02-23 19:58             ` Andy Shevchenko
2023-02-23 22:51               ` Asmaa Mnebhi
2023-02-24  9:47                 ` Andy Shevchenko
2023-02-24 14:42                   ` Asmaa Mnebhi
2023-02-24 15:12                     ` Andy Shevchenko
2023-02-24 15:59                       ` Asmaa Mnebhi
2023-02-24 15:13                     ` Andy Shevchenko
2023-02-24 15:14                       ` Andy Shevchenko
2023-02-18  1:05     ` kernel test robot
2023-02-23 12:29     ` Linus Walleij
2023-02-17 21:26   ` [PATCH v4 2/2] pinctrl: pinctrl-mlxbf: Add pinctrl " Asmaa Mnebhi
2023-02-17 23:24     ` Andy Shevchenko
2023-02-23 21:07       ` Asmaa Mnebhi
2023-02-24  9:44         ` Andy Shevchenko
2023-03-14 20:30           ` Asmaa Mnebhi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=28f0d670407c127614b64d9c382b11c795f5077d.1676668853.git.asmaa@nvidia.com \
    --to=asmaa@nvidia.com \
    --cc=andy.shevchenko@gmail.com \
    --cc=bgolaszewski@baylibre.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-acpi@vger.kernel.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®