From: Chris Boot <bootc@bootc.net>
To: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: linux-kernel@vger.kernel.org
Subject: Re: PANIC: sata_sil on 2.6.16-rc4-ide1
Date: Thu, 23 Feb 2006 10:24:58 +0000 [thread overview]
Message-ID: <2AC65F8C-034E-40FB-98B8-9978A9AE690B@bootc.net> (raw)
In-Reply-To: <1140654241.8672.25.camel@localhost.localdomain>
On 23 Feb 2006, at 00:24, Alan Cox wrote:
> On Mer, 2006-02-22 at 23:53 +0000, Chris Boot wrote:
>> Hi all,
>>
>> I upgraded from 2.6.16-rc2-ide2 to 2.6.16-rc4-ide1 and suffered the
>> panic pasted below. Needless to say this all worked fine with the
>> previous kernel (and some). I have two Seagate 250GB drives connected
>> to the controller (a PCI Adaptec 1205SA). I'm testing -ide so I don't
>> have the whole IDE layer just for my rarely used DVD-RW on my VIA
>> PATA.
>
> Do you see the same crash on 2.6.16-rc4 without the IDE diff ?
Nope, works fine there, except obviously the PATA doesn't! :-)
[4294672.259000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294672.265000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294672.271000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
IRQ sharing disabled
[4294672.280000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294672.288000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294672.295000] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294672.302000] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294672.308000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18
(level, low) -> IRQ 169
[4294672.317000] ata1: SATA max UDMA/100 cmd 0xF8802080 ctl
0xF880208A bmdma 0xF8802000 irq 169
[4294672.327000] ata2: SATA max UDMA/100 cmd 0xF88020C0 ctl
0xF88020CA bmdma 0xF8802008 irq 169
[4294672.538000] ata1: SATA link up 1.5 Gbps (SStatus 113)
[4294672.698000] ata1: dev 0 ATA-7, max UDMA/133, 488397168 sectors:
LBA48
[4294672.705000] ata1: dev 0 configured for UDMA/100
[4294672.711000] scsi0 : sata_sil
[4294672.915000] ata2: SATA link up 1.5 Gbps (SStatus 113)
[4294673.075000] ata2: dev 0 ATA-7, max UDMA/133, 488397168 sectors:
LBA48
[4294673.082000] ata2: dev 0 configured for UDMA/100
[4294673.088000] scsi1 : sata_sil
[4294673.091000] Vendor: ATA Model: ST3250823AS Rev: 3.03
[4294673.100000] Type: Direct-Access ANSI
SCSI revision: 05
[4294673.109000] Vendor: ATA Model: ST3250823AS Rev: 3.03
[4294673.118000] Type: Direct-Access ANSI
SCSI revision: 05
[4294673.127000] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ
11, using IRQ 20
[4294673.135000] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[4294673.142000] ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -
> GSI 20 (level, low) -> IRQ 177
[4294673.153000] PCI: Via IRQ fixup for 0000:00:0f.0, from 11 to 1
[4294673.159000] sata_via 0000:00:0f.0: routed to hard irq line 1
[4294673.201000] ata3: SATA max UDMA/133 cmd 0xB800 ctl 0xBC02 bmdma
0xC800 irq 177
[4294673.244000] ata4: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma
0xC808 irq 177
[4294673.488000] ata3: SATA link up 1.5 Gbps (SStatus 113)
[4294673.682000] ata3: dev 0 ATA-7, max UDMA/133, 488397168 sectors:
LBA48
[4294673.724000] ata3: dev 0 configured for UDMA/133
[4294673.765000] scsi2 : sata_via
[4294674.004000] ata4: SATA link up 1.5 Gbps (SStatus 113)
[4294674.198000] ata4: dev 0 ATA-7, max UDMA/133, 488397168 sectors:
LBA48
[4294674.240000] ata4: dev 0 configured for UDMA/133
[4294674.281000] scsi3 : sata_via
[4294674.319000] Vendor: ATA Model: ST3250823AS Rev: 3.03
[4294674.362000] Type: Direct-Access ANSI
SCSI revision: 05
[4294674.406000] Vendor: ATA Model: ST3250823AS Rev: 3.03
[4294674.450000] Type: Direct-Access ANSI
SCSI revision: 05
HTH,
Chris
--
Chris Boot
bootc@bootc.net
http://www.bootc.net/
prev parent reply other threads:[~2006-02-23 10:25 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-02-22 23:53 Chris Boot
2006-02-23 0:24 ` Alan Cox
2006-02-23 10:24 ` Chris Boot [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2AC65F8C-034E-40FB-98B8-9978A9AE690B@bootc.net \
--to=bootc@bootc.net \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®