Re: [PATCH V4 2/3] clk: qcom: videocc-sm8450: Add video clock controller driver for SM8450

[Taniya Das <quic_tdas@quicinc.com>]

Hello Dmitry,

Thank you for your review.

On 5/10/2023 2:03 AM, Dmitry Baryshkov wrote:
> On Tue, 9 May 2023 at 20:22, Taniya Das <quic_tdas@quicinc.com> wrote:
>>
>> Add support for the video clock controller driver for peripheral clock
>> clients to be able to request for video cc clocks.
>>
>> Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
>> ---
>> Changes since V3:
>>   - Use lower case hex.
>>   - Check the return value here and bail out early on failure in probe.
>>
>> Changes since V2:
>>   - Update the header file name to match the latest upstream header
>>     files.
>>
>> Changes since V1:
>>   - Use DT indices instead of fw_name.
>>   - Replace pm_runtime_enable with devm_pm_runtime_enable.
>>   - Change license to GPL from GPL V2.
>>
>>   drivers/clk/qcom/Kconfig          |   9 +
>>   drivers/clk/qcom/Makefile         |   1 +
>>   drivers/clk/qcom/videocc-sm8450.c | 461 ++++++++++++++++++++++++++++++
>>   3 files changed, 471 insertions(+)
>>   create mode 100644 drivers/clk/qcom/videocc-sm8450.c
> 
> [skipped]
> 
> 
>> +static const struct qcom_reset_map video_cc_sm8450_resets[] = {
>> +       [CVP_VIDEO_CC_INTERFACE_BCR] = { 0x80e0 },
>> +       [CVP_VIDEO_CC_MVS0_BCR] = { 0x8098 },
>> +       [CVP_VIDEO_CC_MVS0C_BCR] = { 0x8048 },
>> +       [CVP_VIDEO_CC_MVS1_BCR] = { 0x80bc },
>> +       [CVP_VIDEO_CC_MVS1C_BCR] = { 0x8070 },
> 
> Can we have a common VIDEO_CC prefix here please?

The BCR names are coming from hardware plan and software interface, thus 
we would like to keep them intact.


> 
>> +       [VIDEO_CC_MVS0C_CLK_ARES] = { 0x8064, 2 },
>> +       [VIDEO_CC_MVS1C_CLK_ARES] = { 0x808c, 2 },
>> +};
>> +

The ARES resets are coming from VideoCC clocks(CBCR), hence the name 
starts with VIDEO_CC.

>> +static const struct regmap_config video_cc_sm8450_regmap_config = {
>> +       .reg_bits = 32,
>> +       .reg_stride = 4,
>> +       .val_bits = 32,
>> +       .max_register = 0x9f4c,
>> +       .fast_io = true,
>> +};
>> +
>> +static struct qcom_cc_desc video_cc_sm8450_desc = {
>> +       .config = &video_cc_sm8450_regmap_config,
>> +       .clks = video_cc_sm8450_clocks,
>> +       .num_clks = ARRAY_SIZE(video_cc_sm8450_clocks),
>> +       .resets = video_cc_sm8450_resets,
>> +       .num_resets = ARRAY_SIZE(video_cc_sm8450_resets),
>> +       .gdscs = video_cc_sm8450_gdscs,
>> +       .num_gdscs = ARRAY_SIZE(video_cc_sm8450_gdscs),
>> +};
>> +
>> +static const struct of_device_id video_cc_sm8450_match_table[] = {
>> +       { .compatible = "qcom,sm8450-videocc" },
>> +       { }
>> +};
>> +MODULE_DEVICE_TABLE(of, video_cc_sm8450_match_table);
>> +
>> +static int video_cc_sm8450_probe(struct platform_device *pdev)
>> +{
>> +       struct regmap *regmap;
>> +       int ret;
>> +
>> +       ret = devm_pm_runtime_enable(&pdev->dev);
>> +       if (ret)
>> +               return ret;
>> +
>> +       ret = pm_runtime_resume_and_get(&pdev->dev);
>> +       if (ret)
>> +               return ret;
>> +
>> +       regmap = qcom_cc_map(pdev, &video_cc_sm8450_desc);
>> +       if (IS_ERR(regmap)) {
>> +               pm_runtime_put(&pdev->dev);
>> +               return PTR_ERR(regmap);
>> +       }
>> +
>> +       clk_lucid_evo_pll_configure(&video_cc_pll0, regmap, &video_cc_pll0_config);
>> +       clk_lucid_evo_pll_configure(&video_cc_pll1, regmap, &video_cc_pll1_config);
>> +
>> +       /*
>> +        * Keep clocks always enabled:
>> +        *      video_cc_ahb_clk
>> +        *      video_cc_sleep_clk
>> +        *      video_cc_xo_clk
>> +        */
>> +       regmap_update_bits(regmap, 0x80e4, BIT(0), BIT(0));
>> +       regmap_update_bits(regmap, 0x8130, BIT(0), BIT(0));
>> +       regmap_update_bits(regmap, 0x8114, BIT(0), BIT(0));
>> +
>> +       ret = qcom_cc_really_probe(pdev, &video_cc_sm8450_desc, regmap);
>> +
>> +       pm_runtime_put(&pdev->dev);
>> +
>> +       return ret;
>> +}
>> +
>> +static struct platform_driver video_cc_sm8450_driver = {
>> +       .probe = video_cc_sm8450_probe,
>> +       .driver = {
>> +               .name = "video_cc-sm8450",
>> +               .of_match_table = video_cc_sm8450_match_table,
>> +       },
>> +};
>> +
>> +static int __init video_cc_sm8450_init(void)
>> +{
>> +       return platform_driver_register(&video_cc_sm8450_driver);
>> +}
>> +subsys_initcall(video_cc_sm8450_init);
>> +
>> +static void __exit video_cc_sm8450_exit(void)
>> +{
>> +       platform_driver_unregister(&video_cc_sm8450_driver);
>> +}
>> +module_exit(video_cc_sm8450_exit);
> 
> module_platform_driver() ?
> 

We would like to keep the clock drivers all probed at subsys_initcall. 
We could revisit and update as cleanup if we want to move them to module 
init.

>> +
>> +MODULE_DESCRIPTION("QTI VIDEO_CC SM8450 Driver");
>> +MODULE_LICENSE("GPL");
>> --
>> 2.17.1
>>
> 
> 

-- 
Thanks & Regards,
Taniya Das.