Re: Aw: Re: [PATCH v4 4/4] arm64: dts: mediatek: mt7988: add pinctrl support

[AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>]

Il 11/10/24 14:53, Frank Wunderlich ha scritto:
> Hi
> 
>> Gesendet: Donnerstag, 10. Oktober 2024 um 14:36 Uhr
>> Von: "AngeloGioacchino Del Regno" <angelogioacchino.delregno@collabora.com>
>> Betreff: Re: [PATCH v4 4/4] arm64: dts: mediatek: mt7988: add pinctrl support
>>
>> Il 09/10/24 18:52, Frank Wunderlich ha scritto:
>>> From: Frank Wunderlich <frank-w@public-files.de>
>>>
>>> Add mt7988a pinctrl node.
>>>
>>> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
>>> ---
>>> v2:
>>> - fix wrong alignment of reg values
>>> ---
>>>    arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 241 ++++++++++++++++++++++
>>>    1 file changed, 241 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/mediatek/mt7988a.dtsi b/arch/arm64/boot/dts/mediatek/mt7988a.dtsi
>>> index c9649b815276..7e15934efe0b 100644
>>> --- a/arch/arm64/boot/dts/mediatek/mt7988a.dtsi
>>> +++ b/arch/arm64/boot/dts/mediatek/mt7988a.dtsi
>>> @@ -3,6 +3,7 @@
>>>    #include <dt-bindings/clock/mediatek,mt7988-clk.h>
>>>    #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>    #include <dt-bindings/phy/phy.h>
>>> +#include <dt-bindings/pinctrl/mt65xx.h>
>>>
>>>    / {
>>>    	compatible = "mediatek,mt7988a";
>>> @@ -105,6 +106,246 @@ clock-controller@1001e000 {
>>>    			#clock-cells = <1>;
>>>    		};
>>>
>>> +		pio: pinctrl@1001f000 {
>>> +			compatible = "mediatek,mt7988-pinctrl";
>>> +			reg = <0 0x1001f000 0 0x1000>,
>>> +			      <0 0x11c10000 0 0x1000>,
>>> +			      <0 0x11d00000 0 0x1000>,
>>> +			      <0 0x11d20000 0 0x1000>,
>>> +			      <0 0x11e00000 0 0x1000>,
>>> +			      <0 0x11f00000 0 0x1000>,
>>> +			      <0 0x1000b000 0 0x1000>;
>>> +			reg-names = "gpio", "iocfg_tr",
>>> +				    "iocfg_br", "iocfg_rb",
>>> +				    "iocfg_lb", "iocfg_tl", "eint";
>>> +			gpio-controller;
>>> +			#gpio-cells = <2>;
>>> +			gpio-ranges = <&pio 0 0 84>;
>>> +			interrupt-controller;
>>> +			interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
>>> +			interrupt-parent = <&gic>;
>>> +			#interrupt-cells = <2>;
>>> +
>>> +			mdio0_pins: mdio0-pins {
>>> +				mux {
>>> +					function = "eth";
>>> +					groups = "mdc_mdio0";
>>> +				};
>>> +
>>> +				conf {
>>> +					pins = "SMI_0_MDC", "SMI_0_MDIO";
>>> +					drive-strength = <MTK_DRIVE_8mA>;
>>
>> Please do *not* use the MTK_DRIVE_(x)mA definitions anymore.
>>
>> Here it is `drive-strength = <8>`.
> 
> OK
> 
>>> +				};
>>> +			};
>>> +
>>> +			i2c0_pins: i2c0-g0-pins {
>>> +				mux {
>>> +					function = "i2c";
>>> +					groups = "i2c0_1";
>>> +				};
>>> +			};
>>> +
>>> +			i2c1_pins: i2c1-g0-pins {
>>> +				mux {
>>> +					function = "i2c";
>>> +					groups = "i2c1_0";
>>> +				};
>>> +			};
>>
>> Whatever pin can be configured with one or multiple groups that can be different
>> must *not* be in the SoC dtsi, but rather in the *board* dts(i) file, as the wanted
>> configuration of those pins is *not* soc-specific but board-specific.
>>
>>   From a fast look, I can see that at least the I2C pins can be assigned to different
>> functions: for example, pins 15+16 can be either of i2c0_1, *or* u30_phy_i2c0, *or*
>> u32_phy_i2c0, *or* xfi_phy0_i2c1 ... or others, even.
>>
>> Finally - I think that *most* of the muxing that you're declaring here must instead
>> go to your board specific devicetree and not in mt7988a.dtsi.
> 
> As far as i see also mdio and uart0 sharing pins with other pin definitions.
> It looks for me that nearly all (except pcie) needs to go in board(s) dts then...
> imho this creates duplicates of same nodes, if 2 boards using the same pinconf.
> But if it is the way to go, i drop all subnodes except the pcie-pins.
> 

That's the way to go. Please drop all subnodes from this one except pcie-pins.

Cheers,
Angelo