Re: [PATCH v2 12/12] [UNTESTED] riscv: dts: starfive: beaglev-starlight: Enable gmac

[Cristian Ciocaltea <cristian.ciocaltea@collabora.com>]

On 11/26/23 23:10, Emil Renner Berthing wrote:
> Cristian Ciocaltea wrote:
>> The BeagleV Starlight SBC uses a Microchip KSZ9031RNXCA PHY supporting
>> RGMII-ID.
>>
>> TODO: Verify if manual adjustment of the RX internal delay is needed. If
>> yes, add the mdio & phy sub-nodes.
> 
> Sorry for being late here. I've tested that removing the mdio and phy nodes on
> the the Starlight board works fine, but the rx-internal-delay-ps = <900>
> property not needed on any of my VisionFive V1 boards either. 

No problem, thanks a lot for taking the time to help with the testing!

> So I wonder why you need that on your board

I noticed you have a patch 70ca054e82b5 ("net: phy: motorcomm: Disable
rgmii rx delay") in your tree, hence I you please confirm the tests were
done with that commit reverted?

> Also in the driver patch you add support for phy-mode = "rgmii-txid", but here
> you still set it to "rgmii-id", so which is it?

Please try with "rgmii-id" first. I added "rgmii-txid" to have a
fallback solution in case the former cannot be used.

> You've alse removed the phy reset gpio on the Starlight board:
> 
>   snps,reset-gpios = <&gpio 63 GPIO_ACTIVE_LOW>
> 
> Why?

I missed this in v1 as the gmac handling was done exclusively in
jh7100-common. Thanks for noticing!

>>
>> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
>> ---
>>  arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts | 5 +++++
>>  1 file changed, 5 insertions(+)
>>
>> diff --git a/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts b/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
>> index 7cda3a89020a..d3f4c99d98da 100644
>> --- a/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
>> +++ b/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
>> @@ -11,3 +11,8 @@ / {
>>  	model = "BeagleV Starlight Beta";
>>  	compatible = "beagle,beaglev-starlight-jh7100-r0", "starfive,jh7100";
>>  };
>> +
>> +&gmac {
>> +	phy-mode = "rgmii-id";
>> +	status = "okay";
>> +};
> 
> Lastly the phy-mode and status are the same for the VF1 and Starlight boards,
> so why can't these be set in the jh7100-common.dtsi?

I wasn't sure "rgmii-id" can be used for both boards and I didn't want
to unconditionally enable gmac on Starlight before getting a
confirmation that this actually works.

If there is no way to make it working with "rgmii-id" (w/ or w/o
adjusting rx-internal-delay-ps), than we should switch to "rgmii-txid".

Thanks,
Cristian