Re: [PATCH 1/2] soc: qcom: dcc: Fix examples list on /sys/kernel/debug/dcc/.../[list-number]/config documentation

[Souradeep Chowdhury <quic_schowdhu@quicinc.com>]

On 12/30/2022 7:20 PM, Bagas Sanjaya wrote:
> kernel test robot reported htmldocs warnings:
> 
> Documentation/ABI/testing/debugfs-driver-dcc:34: WARNING: Unexpected indentation.
> Documentation/ABI/testing/debugfs-driver-dcc:34: WARNING: Block quote ends without a blank line; unexpected unindent.
> 
> Fix these by fixing numbered list syntax on description of
> /sys/kernel/debug/dcc/.../[list-number]/config, including adding blank line
> separators as appropriate.
> 
> Link: https://lore.kernel.org/linux-doc/202212300426.eMLsZsvA-lkp@intel.com/
> Fixes: 4cbe60cf5ad622 ("soc: qcom: dcc: Add driver support for Data Capture and Compare unit(DCC)")
> Reported-by: kernel test robot <lkp@intel.com>
> Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
> ---
>   Documentation/ABI/testing/debugfs-driver-dcc | 63 +++++++++++++-------
>   1 file changed, 41 insertions(+), 22 deletions(-)
> 
> diff --git a/Documentation/ABI/testing/debugfs-driver-dcc b/Documentation/ABI/testing/debugfs-driver-dcc
> index a4680950205931..a00f4502885b58 100644
> --- a/Documentation/ABI/testing/debugfs-driver-dcc
> +++ b/Documentation/ABI/testing/debugfs-driver-dcc
> @@ -44,35 +44,54 @@ Description:
>   		example user can jump to list x only after list y is
>   		configured and enabled. The format for entering all
>   		types of instructions are explained in examples as
> -		follows.
> -		Example:
> -	         i)Read Type Instruction
> +		follows:
> +
> +	        i) Read Type Instruction
> +
>   		   echo R <1> <2> <3> >/sys/kernel/debug/dcc/../[list-number]/config
> +
>   		   1->Address to be considered for reading the value.
> +
>   		   2->The word count of the addresses, read n words
>   		      starting from address <1>. Each word is of 32 bits.
>   		      If not entered 1 is considered.
> +
>   		   3->Can be 'apb' or 'ahb' which indicates if it is apb or ahb
>   		      bus respectively. If not entered ahb is considered.
> -		ii)Write Type Instruction
> -		   echo W <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
> -		   1->Address to be considered for writing the value.
> -		   2->The value that needs to be written at the location.
> -		   3->Can be a 'apb' or 'ahb' which indicates if it is apb or ahb
> -		      but respectively.
> -	       iii)Read Modify Write type instruction
> -		   echo RW <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
> -		   1->The address which needs to be considered for read then write.
> -		   2->The value that needs to be written on the address.
> -		   3->The mask of the value to be written.
> -		iv)Loop Type Instruction
> -		   echo L <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
> -		   1->The loop count, the number of times the value of the addresses will be
> -		      captured.
> -		   2->The address count, total number of addresses to be entered in this
> -		      instruction.
> -		   3->The series of addresses to be entered separated by a space like <addr1>
> -		      <addr2>... and so on.
> +
> +		ii) Write Type Instruction
> +
> +		    echo W <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
> +
> +		    1->Address to be considered for writing the value.
> +
> +		    2->The value that needs to be written at the location.
> +
> +		    3->Can be a 'apb' or 'ahb' which indicates if it is apb or ahb
> +		       but respectively.
> +
> +	        iii) Read Modify Write type instruction
> +
> +		     echo RW <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
> +
> +		     1->The address which needs to be considered for read then write.
> +
> +		     2->The value that needs to be written on the address.
> +
> +		     3->The mask of the value to be written.
> +
> +		iv) Loop Type Instruction
> +
> +		    echo L <1> <2> <3> > /sys/kernel/debug/dcc/../[list-number]/config
> +
> +		    1->The loop count, the number of times the value of the addresses will be
> +		       captured.
> +
> +		    2->The address count, total number of addresses to be entered in this
> +		       instruction.
> +
> +		    3->The series of addresses to be entered separated by a space like <addr1>
> +		       <addr2>... and so on.
>   
>   What:           /sys/kernel/debug/dcc/.../[list-number]/enable
>   Date:           December 2022

Acked-by:Souradeep Chowdhury <quic_schowdhu@quicinc.com>