From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Subject: Re: [PATCH v5 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS
Date: Mon, 28 Nov 2022 15:56:08 +0100 [thread overview]
Message-ID: <3751bf35-d202-99c2-fac1-12d3c69ad00a@linaro.org> (raw)
In-Reply-To: <20221128131016.127860-3-krzysztof.kozlowski@linaro.org>
On 28.11.2022 14:10, Krzysztof Kozlowski wrote:
> From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>
> Add Soundwire controllers, Low Power Audio SubSystem (LPASS) devices and
> LPASS pin controller.
>
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
>
> Changes since v4:
> 1. Re-order few properties between Soundwire nodes, to keep them ordered
> consistently.
> 2. Drop unsupported qcom,port-offset.
>
> Changes since v3:
> 1. Re-order reg and sound-dai-cells.
>
> Changes since v2:
> 1. Use lower-case hex.
>
> Changes since v1:
> 1. Whitespace cleanups.
> 2. Correct include - do not use deprecated one.
> ---
> arch/arm64/boot/dts/qcom/sm8450.dtsi | 292 +++++++++++++++++++++++++++
> 1 file changed, 292 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 7b63c56ff2f4..380405ec3452 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -15,6 +15,7 @@
> #include <dt-bindings/interconnect/qcom,sm8450.h>
> #include <dt-bindings/soc/qcom,gpr.h>
> #include <dt-bindings/soc/qcom,rpmh-rsc.h>
> +#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
> #include <dt-bindings/thermal/thermal.h>
>
> / {
> @@ -2090,6 +2091,209 @@ compute-cb@3 {
> };
> };
>
> + wsa2macro: codec@31e0000 {
> + compatible = "qcom,sm8450-lpass-wsa-macro";
> + reg = <0 0x031e0000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>, <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "wsa2-mclk";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wsa2_swr_active>;
> + #sound-dai-cells = <1>;
> + };
> +
> + /* WSA2 */
> + swr4: soundwire-controller@31f0000 {
> + compatible = "qcom,soundwire-v1.7.0";
> + reg = <0 0x031f0000 0 0x2000>;
> + interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&wsa2macro>;
> + clock-names = "iface";
> +
> + qcom,din-ports = <2>;
> + qcom,dout-ports = <6>;
> +
> + qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
> + qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
> + qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> +
> + #address-cells = <2>;
> + #size-cells = <0>;
> + #sound-dai-cells = <1>;
> + };
> +
> + rxmacro: codec@3200000 {
> + compatible = "qcom,sm8450-lpass-rx-macro";
> + reg = <0 0x3200000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> +
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>, <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "mclk";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rx_swr_active>;
> + #sound-dai-cells = <1>;
> + };
> +
> + swr1: soundwire-controller@3210000 {
> + compatible = "qcom,soundwire-v1.7.0";
> + reg = <0 0x3210000 0 0x2000>;
> + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&rxmacro>;
> + clock-names = "iface";
> + label = "RX";
> + qcom,din-ports = <0>;
> + qcom,dout-ports = <5>;
> +
> + qcom,ports-sinterval-low = /bits/ 8 <0x03 0x1f 0x1f 0x07 0x00>;
> + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x00>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
> + qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
> +
> + #address-cells = <2>;
> + #size-cells = <0>;
> + #sound-dai-cells = <1>;
> + };
> +
> + txmacro: codec@3220000 {
> + compatible = "qcom,sm8450-lpass-tx-macro";
> + reg = <0 0x3220000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>, <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "mclk";
> + pinctrl-names = "default";
> + pinctrl-0 = <&tx_swr_active>;
> + #sound-dai-cells = <1>;
> + };
> +
> + wsamacro: codec@3240000 {
> + compatible = "qcom,sm8450-lpass-wsa-macro";
> + reg = <0 0x03240000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&vamacro>;
> + clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
> +
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>, <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "mclk";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wsa_swr_active>;
> + #sound-dai-cells = <1>;
> + };
> +
> + /* WSA */
> + swr0: soundwire-controller@3250000 {
> + compatible = "qcom,soundwire-v1.7.0";
> + reg = <0 0x03250000 0 0x2000>;
> + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&wsamacro>;
> + clock-names = "iface";
> +
> + qcom,din-ports = <2>;
> + qcom,dout-ports = <6>;
> +
> + qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>;
> + qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>;
> + qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0x01 0xff 0xff 0x01 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> + qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
> +
> + #address-cells = <2>;
> + #size-cells = <0>;
> + #sound-dai-cells = <1>;
> + };
> +
> + swr2: soundwire-controller@33b0000 {
> + compatible = "qcom,soundwire-v1.7.0";
> + reg = <0 0x33b0000 0 0x2000>;
> + interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
> + <&intc GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "core", "wake";
> +
> + clocks = <&vamacro>;
> + clock-names = "iface";
> + label = "TX";
> +
> + qcom,din-ports = <4>;
> + qcom,dout-ports = <0>;
> + qcom,ports-sinterval-low = /bits/ 8 <0x01 0x01 0x03 0x03>;
> + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x01 0x01>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00 0x00>;
> + qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff>;
> + qcom,ports-lane-control = /bits/ 8 <0x01 0x02 0x00 0x00>;
> +
> + #address-cells = <2>;
> + #size-cells = <0>;
> + #sound-dai-cells = <1>;
> + };
> +
> + vamacro: codec@33f0000 {
> + compatible = "qcom,sm8450-lpass-va-macro";
> + reg = <0 0x033f0000 0 0x1000>;
> + clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_CLK_ID_RX_CORE_MCLK2_2X_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + clock-names = "mclk", "macro", "dcodec", "npl";
> + assigned-clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + assigned-clock-rates = <19200000>;
> +
> + #clock-cells = <0>;
> + clock-output-names = "fsgen";
> + #sound-dai-cells = <1>;
> + };
> +
> remoteproc_adsp: remoteproc@30000000 {
> compatible = "qcom,sm8450-adsp-pas";
> reg = <0 0x30000000 0 0x100>;
> @@ -3023,6 +3227,91 @@ qup_uart20_default: qup-uart20-default-state {
>
> };
>
> + lpass_tlmm: pinctrl@3440000{
> + compatible = "qcom,sm8450-lpass-lpi-pinctrl";
> + reg = <0 0x3440000 0x0 0x20000>,
> + <0 0x34d0000 0x0 0x10000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&lpass_tlmm 0 0 23>;
> +
> + clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
> + <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
> + clock-names = "core", "audio";
> +
> + wsa_swr_active: wsa-swr-active-state {
> + clk-pins {
> + pins = "gpio10";
> + function = "wsa_swr_clk";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-disable;
> + };
> +
> + data-pins {
> + pins = "gpio11";
> + function = "wsa_swr_data";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-bus-hold;
> + };
> + };
> +
> + tx_swr_active: tx-swr-active-state {
> + clk-pins {
> + pins = "gpio0";
> + function = "swr_tx_clk";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-disable;
> + };
> +
> + data-pins {
> + pins = "gpio1", "gpio2", "gpio14";
> + function = "swr_tx_data";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-bus-hold;
> + };
> + };
> +
> + rx_swr_active: rx-swr-active-state {
> + clk-pins {
> + pins = "gpio3";
> + function = "swr_rx_clk";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-disable;
> + };
> +
> + data-pins {
> + pins = "gpio4", "gpio5";
> + function = "swr_rx_data";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-bus-hold;
> + };
> + };
> +
> + wsa2_swr_active: wsa2-swr-active-state {
> + clk-pins {
> + pins = "gpio15";
> + function = "wsa2_swr_clk";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-disable;
> + };
> +
> + data-pins {
> + pins = "gpio16";
> + function = "wsa2_swr_data";
> + drive-strength = <2>;
> + slew-rate = <1>;
> + bias-bus-hold;
> + };
> + };
> + };
> +
> apps_smmu: iommu@15000000 {
> compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
> reg = <0 0x15000000 0 0x100000>;
> @@ -3501,6 +3790,9 @@ lpass_ag_noc: interconnect@3c40000 {
> };
> };
>
> + sound: sound {
> + };
> +
> thermal-zones {
> aoss0-thermal {
> polling-delay-passive = <0>;
next prev parent reply other threads:[~2022-11-28 14:56 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-28 13:10 [PATCH v5 0/3] arm64: dts: qcom: sm8450-hdk: add sound support Krzysztof Kozlowski
2022-11-28 13:10 ` [PATCH v5 1/3] arm64: dts: qcom: sm8450: add GPR node Krzysztof Kozlowski
2022-11-28 13:10 ` [PATCH v5 2/3] arm64: dts: qcom: sm8450: add Soundwire and LPASS Krzysztof Kozlowski
2022-11-28 14:56 ` Konrad Dybcio [this message]
2022-11-28 13:10 ` [PATCH v5 3/3] arm64: dts: qcom: sm8450-hdk: add sound support Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3751bf35-d202-99c2-fac1-12d3c69ad00a@linaro.org \
--to=konrad.dybcio@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=srinivas.kandagatla@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®