Re: [PATCH v2 3/5] arm64: dts: qcom: sm8350: add dp controller

[Neil Armstrong <neil.armstrong@linaro.org>]

On 10/02/2023 12:08, Dmitry Baryshkov wrote:
> On 10/02/2023 12:34, Neil Armstrong wrote:
>> Add the Display Port controller subnode to the MDSS node.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>>   arch/arm64/boot/dts/qcom/sm8350.dtsi | 82 +++++++++++++++++++++++++++++++++++-
>>   1 file changed, 80 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
>> index d490ce84a022..eb636b7dffa7 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
>> @@ -2862,13 +2862,20 @@ ports {
>>                       port@0 {
>>                           reg = <0>;
>> -                        dpu_intf1_out: endpoint {
>> -                            remote-endpoint = <&mdss_dsi0_in>;
>> +                        dpu_intf0_out: endpoint {
>> +                            remote-endpoint = <&mdss_dp_in>;
> 
> No need to reorder these ports. Please add DP to the end.

Right, but I'll keep the dpu_intf0_out label for this port,
but having dpu_intf1_out, dpu_intf2_out then dpu_intf0_out isn't very clean...

> 
>>                           };
>>                       };
>>                       port@1 {
>>                           reg = <1>;
>> +                        dpu_intf1_out: endpoint {
>> +                            remote-endpoint = <&mdss_dsi0_in>;
>> +                        };
>> +                    };
>> +
>> +                    port@2 {
>> +                        reg = <2>;
>>                           dpu_intf2_out: endpoint {
>>                               remote-endpoint = <&mdss_dsi1_in>;
>>                           };
>> @@ -2876,6 +2883,77 @@ dpu_intf2_out: endpoint {
>>                   };
>>               };
>> +            mdss_dp: displayport-controller@ae90000 {
>> +                compatible = "qcom,sm8350-dp";
>> +                reg = <0 0xae90000 0 0x200>,
>> +                      <0 0xae90200 0 0x200>,
>> +                      <0 0xae90400 0 0x600>,
>> +                      <0 0xae91000 0 0x400>;
> 
> This will not validate against the schema. Please add p1 region at the end (I assume it is <0 0x0ae91400 0 0x400>).
> 
>> +                interrupt-parent = <&mdss>;
>> +                interrupts = <12>;
>> +                clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
>> +                     <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
>> +                     <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
>> +                     <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
>> +                     <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
>> +                clock-names = "core_iface",
>> +                          "core_aux",
>> +                          "ctrl_link",
>> +                                  "ctrl_link_iface",
>> +                          "stream_pixel";
>> +
>> +                assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
>> +                          <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
>> +                assigned-clock-parents = <&usb_1_qmpphy 1>,
>> +                             <&usb_1_qmpphy 2>;
> 
> Please use defined names here and in the phys below

Ack, will do in all the patches

> 
>> +
>> +                phys = <&usb_1_qmpphy 1>;
>> +                    phy-names = "dp";
>> +
>> +                    #sound-dai-cells = <0>;
>> +
>> +                operating-points-v2 = <&dp_opp_table>;
>> +                power-domains = <&rpmhpd SM8350_MMCX>;
>> +
>> +                status = "disabled";
>> +
>> +                ports {
>> +                    #address-cells = <1>;
>> +                    #size-cells = <0>;
>> +
>> +                    port@0 {
>> +                        reg = <0>;
>> +                        mdss_dp_in: endpoint {
>> +                            remote-endpoint = <&dpu_intf0_out>;
>> +                        };
>> +                    };
>> +                };
>> +
>> +                dp_opp_table: opp-table {
>> +                    compatible = "operating-points-v2";
>> +
>> +                    opp-160000000 {
>> +                        opp-hz = /bits/ 64 <160000000>;
>> +                        required-opps = <&rpmhpd_opp_low_svs>;
>> +                    };
>> +
>> +                    opp-270000000 {
>> +                        opp-hz = /bits/ 64 <270000000>;
>> +                        required-opps = <&rpmhpd_opp_svs>;
>> +                    };
>> +
>> +                    opp-540000000 {
>> +                        opp-hz = /bits/ 64 <540000000>;
>> +                        required-opps = <&rpmhpd_opp_svs_l1>;
>> +                    };
>> +
>> +                    opp-810000000 {
>> +                        opp-hz = /bits/ 64 <810000000>;
>> +                        required-opps = <&rpmhpd_opp_nom>;
>> +                    };
>> +                };
>> +            };
>> +
>>               mdss_dsi0: dsi@ae94000 {
>>                   compatible = "qcom,sm8350-dsi-ctrl", "qcom,mdss-dsi-ctrl";
>>                   reg = <0 0x0ae94000 0 0x400>;
>>
>