Re: PCI probing failure in 2.6.21-rc3

["Francis Moreau" <francis.moro@gmail.com>]

[-- Attachment #1: Type: text/plain, Size: 600 bytes --]

Hi

On 3/15/07, Andrew Morton <akpm@linux-foundation.org> wrote:
> Greg, could we please either
>
> a) start doing something about these reports or
> b) publish sufficient info to permit others to do something about these
>    reports or
> c) remove the printk?
>

Thanks Andrew for considering.

I eventually tried to add "pci=assign-busses" as it was suggested by
the initial console output but I still have some issues I think. For
example:

$ dmesg
[...]
PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
[...]

I join the corresponding dmesg.

Hope that helps.
-- 
Francis

[-- Attachment #2: dmesg --]
[-- Type: application/octet-stream, Size: 25583 bytes --]

Linux version 2.6.21-rc3 (fmoreau@laptop) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-51)) #1 SMP Wed Mar 14 08:55:15 CET 2007
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb pci=assign-busses
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fe80000 (usable)
 BIOS-e820: 000000003fe80000 - 000000003ff00000 (ACPI NVS)
 BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
 BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
 BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 261760) 1 entries of 3200 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F64E0, 0014 (r0 PTLTD )
ACPI: RSDT 3FE85369, 0050 (r1 PTLTD  Capell00  6040000  LTP        0)
ACPI: FACP 3FE8CE20, 0074 (r1 Acer   Grape     6040000 LOHR       5A)
ACPI: DSDT 3FE8708A, 5D96 (r1 Acer   CALISTGA  6040000 INTL 20050228)
ACPI: FACS 3FE8DFC0, 0040
ACPI: APIC 3FE8CE94, 0068 (r1 Acer   Grape     6040000 LOHR       5A)
ACPI: HPET 3FE8CEFC, 0038 (r1 Acer   Grape     6040000 LOHR       5A)
ACPI: MCFG 3FE8CF34, 003C (r1 Acer   Grape     6040000 LOHR       5A)
ACPI: APIC 3FE8CF70, 0068 (r1 PTLTD  	 APIC    6040000  LTP        0)
ACPI: BOOT 3FE8CFD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
ACPI: SSDT 3FE86A3B, 064F (r1 SataRe  SataPri     1000 INTL 20050228)
ACPI: SSDT 3FE863A9, 0692 (r1 SataRe  SataSec     1000 INTL 20050228)
ACPI: SSDT 3FE85945, 025F (r1  PmRef  Cpu0Tst     3000 INTL 20050228)
ACPI: SSDT 3FE8589F, 00A6 (r1  PmRef  Cpu1Tst     3000 INTL 20050228)
ACPI: SSDT 3FE853B9, 04E6 (r1  PmRef    CpuPm     3000 INTL 20050228)
No NUMA configuration found
Faking a node at 0000000000000000-000000003fe80000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 261760) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003fe80000
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   261760
On node 0 totalpages: 261663
  DMA zone: 64 pages used for memmap
  DMA zone: 1340 pages reserved
  DMA zone: 2595 pages, LIFO batch:0
  DMA32 zone: 4026 pages used for memmap
  DMA32 zone: 253638 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 43136 bytes of per cpu data
Built 1 zonelists.  Total pages: 256233
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb pci=assign-busses
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 1662.503 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 1020800k/1047040k available (2412k kernel code, 25852k reserved, 1431k data, 324k init)
Calibrating delay using timer specific routine.. 3328.49 BogoMIPS (lpj=1664246)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 10390648
Detected 10.390 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.03 BogoMIPS (lpj=1662519)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU         T5500  @ 1.66GHz stepping 06
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=24
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
0000:00:1f.2: trying to change BAR0 from 0000 to 01F0
0000:00:1f.2: trying to change BAR1 from 0000 to 03F4
0000:00:1f.2: trying to change BAR2 from 0000 to 0170
0000:00:1f.2: trying to change BAR3 from 0000 to 0374
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 5 *6 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 5 6 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 5 6 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 5 6 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 5 6 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 5 6 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 5 6 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 *5 6 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
pnp: 00:01: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
Time: hpet clocksource has been installed.
pnp: 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
pnp: 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: d0000000-d1ffffff
  PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
  IO window: disabled.
  MEM window: d2100000-d21fffff
  PREFETCH window: disabled.
PCI: Bus 7, cardbus bridge: 0000:06:04.0
  IO window: 00002000-000020ff
  IO window: 00002400-000024ff
  PREFETCH window: 50000000-53ffffff
  MEM window: 54000000-57ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 2000-2fff
  MEM window: d2000000-d20fffff
  PREFETCH window: 50000000-53ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 16 (level, low) -> IRQ 16
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 65536 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2308k freed
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1173995016.797:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: SSDT 3FE860EB, 01F6 (r1  PmRef  Cpu0Ist     3000 INTL 20050228)
ACPI: SSDT 3FE85BA4, 04C2 (r1  PmRef  Cpu0Cst     3001 INTL 20050228)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 3FE862E1, 00C8 (r1  PmRef  Cpu1Ist     3000 INTL 20050228)
ACPI: SSDT 3FE86066, 0085 (r1  PmRef  Cpu1Cst     3000 INTL 20050228)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (41 C)
ACPI: Thermal Zone [TZ01] (41 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: Slimtype DVDRW SSM-8515S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
Yenta: CardBus bridge found at 0000:06:04.0 [1025:0090]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:04.0, mfunc 0x90501212, devctl 0x44
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
pcmcia: parent PCI bridge Memory window: 0xd2000000 - 0xd20fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 324k freed
Write protecting the kernel read-only data: 1074k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-2: new full speed USB device using uhci_hcd and address 2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd2404000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI subsystem initialized
libata version 2.20 loaded.
ata_piix 0000:00:1f.2: version 2.10ac1
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ata: 0x170 IDE port busy
ata: conflict with ide1
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x00000000000118b0 irq 14
ata2: DUMMY
scsi0 : ata_piix
usb 5-4: new high speed USB device using ehci_hcd and address 2
usb 5-4: configuration #1 chosen from 1 choice
ata1.00: ATA-7: Hitachi HTS541212H9AT00, HP4OA23C, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48 
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
scsi1 : ata_piix
scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54121 HP4O PQ: 0 ANSI: 5
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
usb 4-1: new low speed USB device using uhci_hcd and address 2
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 4-1: configuration #1 chosen from 1 choice
input: Microsoft Microsoft Wireless Optical Mouse® 1.00 as /class/input/input2
input: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse® 1.00] on usb-0000:00:1d.3-1
security:  3 users, 6 roles, 1604 types, 175 bools, 1 sens, 1024 cats
security:  59 classes, 50462 rules
security:  class dccp_socket not defined in policy
security:  permission dccp_recv in class node not defined in policy
security:  permission dccp_send in class node not defined in policy
security:  permission dccp_recv in class netif not defined in policy
security:  permission dccp_send in class netif not defined in policy
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1173995021.302:2): policy loaded auid=4294967295
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:06:01.0 to 64
eth0: Broadcom 4400 10/100BaseT Ethernet 00:16:d4:54:64:8f
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
input: PC Speaker as /class/input/input3
intel_rng: FWH not detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:06:04.2 [1524:0550] (rev 1)
PCI: Enabling device 0000:06:04.2 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:04.2[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:06:04.2 to 64
mmc0: SDHCI at 0xd2003400 irq 17 DMA
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
floppy0: no floppy controllers found
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ACPI: AC Adapter [ACAD] (off-line)
ACPI: Battery Slot [BAT1] (battery present)
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input6
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /class/input/input7
ACPI: Power Button (CM) [PWRB]
No dock devices found.
ibm_acpi: ec object not found
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda5, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.2.0d
ipw3945: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:05:00.0 to 64
ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
ieee80211_crypt: registered algorithm 'WEP'
ADDRCONF(NETDEV_UP): eth1: link is not ready
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
eth1: no IPv6 routers present
atkbd.c: Unknown key pressed (translated set 2, code 0xb4 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xb4 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xb4 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xb4 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.