From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id ; Tue, 19 Jun 2001 18:38:26 -0400 Received: (majordomo@vger.kernel.org) by vger.kernel.org id ; Tue, 19 Jun 2001 18:38:16 -0400 Received: from wb1-a.mail.utexas.edu ([128.83.126.134]:6163 "HELO mail.utexas.edu") by vger.kernel.org with SMTP id ; Tue, 19 Jun 2001 18:38:07 -0400 Message-ID: <3B2F2B61.5E591C74@mail.utexas.edu> Date: Tue, 19 Jun 2001 16:37:21 +0600 From: "Bobby D. Bryant" Organization: (I do not speak for) The University of Texas at Austin (nor they for me). X-Mailer: Mozilla 4.77 [en] (X11; U; Linux 2.4.5-ac14 i686) X-Accept-Language: en,fr,de MIME-Version: 1.0 To: "linux-kernel@vger.kernel.org" Subject: FYI: 2.4.5-ac16 panics on Asus A7A266 Content-Type: multipart/mixed; boundary="------------98D1CF63F9E16D0CF4290087" Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org This is a multi-part message in MIME format. --------------98D1CF63F9E16D0CF4290087 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit I tried 2.4.5-ac16 on my Asus A7A266 w/ Athlon because the fixnotes sounded like it might address the simplex vs. DMA problem that I reported a while back, but I get a kernel panic early in the boot sequence every time I try to boot. FYI, 2.4.5-ac14 boots and runs OK, except for the disabled DMA and frequent SMBus resets when I try to run lm_sensors. (The only difference in the .config between -ac14 and -ac16 is that for -ac16 I enabled the new ALI chipset fix.) Possibly relevant, notice that 2.4.5-ac14 reports the chipset as "ALI15X3" during the boot sequence, whereas the board's documentation says that it's actually an ALi M1535D+. It also gives this message at boot time, which I will send to the indicated address in a separate message: Jun 19 15:49:36 pollux kernel: PCI: Found IRQ 9 for device 00:0d.0 Jun 19 15:49:36 pollux kernel: Redundant entry in serial pci_table. Please send the output of Jun 19 15:49:36 pollux kernel: lspci -vv, this message (4793,4104,4793,215) Jun 19 15:49:36 pollux kernel: and the manufacturer and name of serial board or modem board Jun 19 15:49:36 pollux kernel: to serial-pci-info@lists.sourceforge.net. Jun 19 15:49:36 pollux kernel: ttyS04 at port 0x9800 (irq = 9) is a 16550A The lspci info is attached, in case anyone here wants it. Holler if you want more, and tell this cluebie how to collect it. Thanks, Bobby Bryant Austin, Texas --------------98D1CF63F9E16D0CF4290087 Content-Type: text/plain; charset=us-ascii; name="temp.txt" Content-Transfer-Encoding: 7bit Content-Disposition: inline; filename="temp.txt" 00:00.0 Host bridge: Acer Laboratories Inc. [ALi]: Unknown device 1647 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Capabilities: [a4] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5247 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- SERR- Reset- FastB2B- 00:04.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if fa) Subsystem: Asustek Computer, Inc.: Unknown device 8053 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- TAbort- SERR- TAbort- SERR- [disabled] [size=64K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0b.0 Unknown mass storage controller: Promise Technology, Inc. 20267 (rev 02) Subsystem: Promise Technology, Inc.: Unknown device 4d33 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- [disabled] [size=64K] Capabilities: [58] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0d.0 Serial controller: US Robotics/3Com 56K FaxModem Model 5610 (rev 01) (prog-if 02 [16550]) Subsystem: US Robotics/3Com: Unknown device 00d7 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- TAbort- SERR- TAbort- SERR-