From: Fredo David <FredoDavid@gmx.net>
To: linux-kernel@vger.kernel.org
Subject: PROBLEM: IDS2000 crashed during kernel oops.
Date: Fri, 01 Mar 2002 22:51:36 +0100 [thread overview]
Message-ID: <3C7FF7E8.9020200@gmx.net> (raw)
[1.] One line summary of the problem:
IDS.2000 crashed during a kernel oops.
[2.] Full description of the problem/report:
During a Kernel- Update from 2.2.16 to 2.2.19 with SuSE Linux 7.0 we ran
into the following problem. We use an Informix DB with raw devices.
The Database IDS.2000, running on a Linux 2.2.19 machine crashes during
a DB- backup with onbar -b -w or during a DB- Log- Backup with onbar -b
-l on a tape.
The last message in the online.log and bar_act.log:
2002-03-01 11:40:41 Checkpoint Completed: duration was 0 seconds.
2002-03-01 11:40:41 Checkpoint loguniq 2347, logpos 0x150018
2002-03-01 11:40:43 Level 0 Archive started on rootdbs, xsvblobdbs,
physdbs, logdbs, xsvdbs
2002-03-01 11:40:43 Fatal error in ADM VP at mt.c:11462
2002-03-01 11:40:43 Unexpected virtual processor termination, pid=439,
exit = 0xb
2002-03-01 11:40:44 PANIC: Attempting to bring system down
2002-03-01 11:40:44 semctl: errno = 22
2002-03-01 11:40:44 semctl: errno = 22
Every time I started the DB again, when running onbar -b -l on tape, the
IDS crashes.
[3.] Keywords
IDS.2000 Informix oops rawio
[4.] Kernel version
Linux version 2.2.19 (root@srvixdb1) (gcc version 2.95.2 19991024
(release)) #2 Wed Feb 27 15:43:48 CET 2002
[5.] Output of Oops.message(if applicable) with symbolic information
resolved
Mar 1 11:40:43 srvixdb1 kernel: Unable to handle kernel paging request
at virtual address b000e400
Mar 1 11:40:43 srvixdb1 kernel: current->tss.cr3 = 28e7c000, %cr3 =
28e7c000
Mar 1 11:40:43 srvixdb1 kernel: *pde = 00000000
Mar 1 11:40:43 srvixdb1 kernel: Oops: 0002
Mar 1 11:40:43 srvixdb1 kernel: CPU: 0
Mar 1 11:40:43 srvixdb1 kernel: EIP: 0010:[kiobuf_copy_bounce+155/204]
Mar 1 11:40:43 srvixdb1 kernel: EFLAGS: 00010206
Mar 1 11:40:43 srvixdb1 kernel: eax: b000e000 ebx: 00000400 ecx:
00000300 edx: 00000c00
Mar 1 11:40:43 srvixdb1 kernel: esi: cdbef400 edi: b000e400 ebp:
0000f800 esp: e8e7be1c
Mar 1 11:40:43 srvixdb1 kernel: ds: 0018 es: 0018 ss: 0018
Mar 1 11:40:43 srvixdb1 kernel: Process oninit (pid: 439, process nr:
54, stackpage=e8e7b000)
Mar 1 11:40:43 srvixdb1 kernel: Stack: 00000000 00000001 c02eaa40
c02c6e00 e8e7be48 00000000 00000c00 f0463000
Mar 1 11:40:43 srvixdb1 kernel: 00000000 c012a954 f0463000
00000001 0000f800 00000000 00000c00 f0463000
Mar 1 11:40:43 srvixdb1 kernel: 0000f800 00000000 f0463000
00003a03 0003f967 c012ac55 00000000 00000001
Mar 1 11:40:43 srvixdb1 kernel: Call Trace: [<f0463000>]
[cleanup_bounce_buffers+60/92] [<f0463000>] [<f0463000>] [<f0463000>]
[brw_kiovec+737/764] [<f04631ac>]
Mar 1 11:40:43 srvixdb1 kernel: Code: f3 a5 f6 c2 02 74 02 66 a5 f6 c2
01 74 01 a4 89 f6 29 d5 31
Using defaults from ksymoops -t elf32-i386 -a i386
Trace; f0463000 <[eepro100].data.end+13edd/1ef31>
Code; 00000000 Before first symbol
00000000 <_EIP>:
Code; 00000000 Before first symbol
0: f3 a5 repz movsl %ds:(%esi),%es:(%edi)
Code; 00000002 Before first symbol
2: f6 c2 02 test $0x2,%dl
Code; 00000005 Before first symbol
5: 74 02 je 9 <_EIP+0x9> 00000009 Before
first symbol
Code; 00000007 Before first symbol
7: 66 a5 movsw %ds:(%esi),%es:(%edi)
Code; 00000009 Before first symbol
9: f6 c2 01 test $0x1,%dl
Code; 0000000c Before first symbol
c: 74 01 je f <_EIP+0xf> 0000000f Before
first symbol
Code; 0000000e Before first symbol
e: a4 movsb %ds:(%esi),%es:(%edi)
Code; 0000000f Before first symbol
f: 89 f6 mov %esi,%esi
Code; 00000011 Before first symbol
11: 29 d5 sub %edx,%ebp
Code; 00000013 Before first symbol
13: 31 00 xor %eax,(%eax)
[6.] A small shell script or example program which triggers the
problem(if possible)
None
[7.] Environment
[7.1.] Software(add the output of the ver_linux script here)
/usr/src/linux-2.2.19.SuSE/scripts/ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux srvixdb1 2.2.19 #2 Wed Feb 27 15:43:48 CET 2002 i686 unknown
Gnu C 2.95.2
Gnu make 3.79.1
binutils 2.9.5.0.24
util-linux 2.10m
modutils 2.3.11
e2fsprogs 1.18
Linux C Library x 1 root root 4070406 Jul 30 2000
/lib/libc.so.6
Dynamic linker (ldd) 2.1.3
Procps 2.0.6
Net-tools 1.56
Kbd 0.99
Sh-utils 2.0
Modules Loaded ipv6 eepro100 serial usbcore gdth
[7.2.] Processor information:
cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 6
cpu MHz : 930.930
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
sep_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx
fxsr xmm
bogomips : 1854.66
[7.3.] Module information
cat /proc/modules
ipv6 100328 -1 (autoclean)
eepro100 17432 1 (autoclean)
serial 42804 0 (autoclean)
usbcore 44008 0 (unused)
gdth 78128 3
[7.4.] Loaded driver and hardware information
cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
02f8-02ff : serial(auto)
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
f0451000-f045101f : Intel Speedo3 Ethernet
[7.5.] PCI information
lspci -vvv
00:00.0 Host bridge: Acer Laboratories Inc. [ALi] M1621 (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable)
Capabilities: [b0] AGP version 1.0
Status: RQ=27 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [a4] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME (D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5247 (rev 01) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000dfff
Memory behind bridge: f2000000-f3efffff
Prefetchable memory behind bridge: f5f00000-f7ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:06.0 Multimedia audio controller: Acer Laboratories Inc. [ALi]:
Unknown device 5451 (rev 01)
Subsystem: Asustek Computer, Inc.: Unknown device 8021
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR+ <PERR+
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at d800
Region 1: Memory at f1800000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2 +,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge
[Aladdin IV]
Subsystem: Acer Laboratories Inc. [ALi] ALI M1533 Aladdin IV ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME (D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100]
(rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f5000000 (32-bit, prefetchable)
Region 1: I/O ports at d400
Region 2: Memory at f1000000 (32-bit, non-prefetchable)
00:0b.0 SCSI storage controller: ICP Vortex Computersysteme GmbH:
Unknown device 013a
Subsystem: ICP Vortex Computersysteme GmbH: Unknown device 013a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f4000000 (32-bit, prefetchable)
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME (D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c3)
(prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at d000
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME (D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 Bridge: Acer Laboratories Inc. [ALi] M7101 PMU
Subsystem: Asustek Computer, Inc.: Unknown device 8021
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:14.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03)
(prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 8021
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f0800000 (32-bit, non-prefetchable)
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME (D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation Riva TNT2 (rev 20)
(prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 8021
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f2000000 (32-bit, non-prefetchable)
Region 1: Memory at f6000000 (32-bit, prefetchable)
Expansion ROM at f5ff0000 [disabled]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME (D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
[7.6.] SCSI information
cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ICP Model: Host Drive #00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: ICP Model: Host Drive #01 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: ICP Model: Host Drive #02 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: ICP Model: Host Drive #04 Rev:
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 01 Id: 04 Lun: 00
Vendor: HP Model: C5683A Rev: C005
Type: Sequential-Access ANSI SCSI revision: 02
Any help would be appreciated.
Fredo
next reply other threads:[~2002-03-01 21:51 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-03-01 21:51 Fredo David [this message]
2002-03-01 22:16 ` Alan Cox
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3C7FF7E8.9020200@gmx.net \
--to=fredodavid@gmx.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®